Winchester, CA

Upon arrival performed heating tune up. Indoor motor is leaking a ton of oil. Indoor blower wheel had a lot of dust build up combined with rust. Return ducting is very undersized, would recommend enlargement to have more airflow pass through system so motor won’t over heat and leak oil. Ducts are just connected to system with nothing sealed around, system has been sucking in air and debree from attic. Tried to dust off burners but metal is stained from over time. System has no sediment trap for gas valve. Secondary motor control is out of range. Flame sensor looks very weak. Client is looking forward to premier + options. Has to speak over with the wife & will call the shop if wants to move forward with repairs. Also advised client should look into long term replacement options for system due to age & efficiency.

Upon arrival performed heating tune up. Indoor motor is leaking a ton of oil. Indoor blower wheel had a lot of dust build up combined with rust. Return ducting is very undersized, would recommend enlargement to have more airflow pass through system so motor won’t over heat and leak oil. Ducts are just connected to system with nothing sealed around, system has been sucking in air and debree from attic. Tried to dust off burners but metal is stained from over time. System has no sediment trap for gas valve. Secondary motor control is out of range. Flame sensor looks very weak. Client is looking forward to premier + options. Has to speak over with the wife & will call the shop if wants to move forward with repairs. Also advised client should look into long term replacement options for system due to age & efficiency.

Upon arrival client said system was not operational. Found no power to the thermostat. Inspection found the door switch fell off. Locking out the unit. Did full system inspection. Found multiple design and equipment issues. Drain lines were not installed correctly. Needs to get redone plus add safety switches. Both blower motors in units are leaking oil and should be replaced. Found both capacitors weak as well. Control boards had a hot spots on them. They are operational at this time could can fail. Found cracks in both heat exchangers. Turned power off at breaker. Advised client. Return ducts are undersized, causing the downstairs system to over heat. Went over all repair options with client. They want to rebuild the system but they want to see replacement options as well. Ordering heat exchangers from manufacture. Supervisor is scheduled to come out Monday 4-6

Quality control check

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance in the attic by performing a duct leakage inspection. I then proceeded to the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filters have been changed, home owner supplied. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of both units I found there to be no form of electrical protection on either, recommend adding surge protection to both units to protect the sensitive electrical components contained within the system. Upon departure system is working and operational.

Upon arrival installed the new fan motor and rollout switch. Tested system. It’s operational upon departure. 1 year parts/labor

Reset the gas valve, this was left off from previous visit.

Preformed furnace/AC maintenance on 2018 Lennox system

Performed heating maintenance on a Gas furnace in a manufactured home. Systems heating temperature split is within range. Sensors and switches were cleaned and tested. Electrical motors are reading in range. Start components were measured and recorded. Gas valve and ignitor are clean and tested. Filter is ok. Blower housing was cleaned. Burn marks are visible on the control board. This is a cause for concern and can cause issues in the future. Condition of the system was discussed with Laura. System is operational at end of appointment.

Upon arrival, found a 16 year old Bryant furnace. Started maintenance. Heat rise was okay. Static pressure was high. Blower motor is leaking oil and drawing high amps. Inducer motor is also using high amps. Combustion test found higher than normal levels of CO in the exhaust vent. Ignition components are okay. Found a hot spot on the control module. Client declined heat exchanger inspection. Recommend preventively replacing the blower motor to avoid future service calls during the summer. System is operational upon departure.

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance in the attic by performing a duct leakage inspection. I then proceeded to the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Main filter has been changed, the four bedrooms filters need to be changed, home owner stated he will. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of the indoor furnace I found there to be no form of condensate safety, recommend adding to prevent any potential flood damage. Upon departure system is working and operational.

Performed furnace maintenance on 2 14 year old units. Cycled systems for heating. Verified proper heating sequence of operations. Temperature rise across heat exchangers within range. Ran systems through 20 point inspection checklist. Homeowner will be replacing filters. Went over maintenance inspection checklists. Went through concerns and recommendations as well as repair options. Homeowner wants to go ahead and move forward with immediate repairs for indoor units today, and hold off on the outdoor motor until the summer maintenance visit. Replaced secondary motor controls on both indoor units. Cycled systems. Systems are fully operational upon departure.

Upon arrival found 19 year old Goodman heater. Found multiple issues with system. Blower motor is leaking a large amount of oil. Is close to failing. Blower capacitor is also leaking fluid and is reading weak. Temperature rise is okay. Inside the unit was really dirty. Gas line is not up to code, might not pass inspection when it comes time. Went over condition of outdoor unit from previous visit. Informed client of failing parts. Created repair options. Unit is operational upon departure.

Upon arrival, started tune up on 2 18 year old comfort makers. Upstairs system: all electrical motors on this system were failing. Inducer motor is over amping. Failed the electrical inspection. Blower motor is leaking oil and is drawing high amps. Should be replaced soon. Return duct is super dirty. Blower cap is low and had failed. Control module has hot spots around the blower relay. Unit is in poor shape, however it’s operational. Downstairs system: flame rollout switch has broken off. Needs immediate replacement of sensor. Blower motor is leaking SERIOUS oil. Needs immediate replacement. Inducer motor is okay. Control module has hot spots on blower relay. EVAP COIL HAS GROWTH ON IT. which is a big health concern. Disabled system at breaker until repair on flame sensor is made. Only the upstairs is operational at this time.

Upon arrival performed maintenance on Lennox heating system. Zoning is in working order. Cleaned flame sensor. Dusted off all electrical connections. Indoor motor and wheel are in very good condition. Advised running surge protection on system. Filter client replaces. Thermostats in working order. Amperages throughout system are in range. System is operational upon departure.

Upon arrival performed maintenance on Lennox heating system. Zoning is in working order. Cleaned flame sensor. Dusted off all electrical connections. Indoor motor and wheel are in very good condition. Advised running surge protection on system. Filter client replaces. Thermostats in working order. Amperages throughout system are in range. System is operational upon departure.

Upon arrival performed maintenance on Lennox heating system. Zoning is in working order. Cleaned flame sensor. Dusted off all electrical connections. Indoor motor and wheel are in very good condition. Advised running surge protection on system. Filter client replaces. Thermostats in working order. Amperages throughout system are in range. System is operational upon departure.

Upon arrival performed maintenance on Lennox heating system. Zoning is in working order. Cleaned flame sensor. Dusted off all electrical connections. Indoor motor and wheel are in very good condition. Advised running surge protection on system. Filter client replaces. Thermostats in working order. Amperages throughout system are in range. System is operational upon departure.

Serviced carrier zoned furnace. Tested both thermostats and monitored ignition. Measured motor draws and voltages. Tested controls. Cleaned the flame sensor. Measured ignitor. Recorded temp rise. Tightened connections. Removed and inspected blower motor. Inspected the heat exchanger. Inspected ducting and return plenum. Wiped down system. Bled both dampers.

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance in the attic by performing a duct leakage inspection. I then proceeded to the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been checked, does not need to be changed at this time. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of the indoor unit I found there to be no form of surge protection, recommend adding to protect the sensitive electrical components contained within the furnace, condenser is equipped with surge protection. Upon departure system is working and

Installed a bad high limit switch on a carrier gas furnace. This fixed the issue and a continued to Perform maintenance on a 2014 carrier gas furnace. Systems heating temperature split is in range. Sensors and switches were cleaned and tested. Gas valve and ignitor were measured and recorded. Duct runs are sealed. Condensate lines are clear but have no overflow switch. Blower wheel has dust buildup and should be cleaned or monitored moving forward. The customer had questions with nest thermostat that was switching temperature. I disabled the learning feature of the nest as well as eco mode. The condition of the unit was discussed with the homeowner. System is operational.

Installation of Lennox Duel Fuel Variable Speed system with duct cleaning being subbed out. Client is only liable for payment of $15,377, Tech Clean California Rebate Company will be covering remaining $3,000 balance.

Arrived for a fall maintenance. Upon arrival customer reports system heating intermittently. Found high limit switch is tripping. No major air flow issues found. Temperature rise is 42 when the switch trips. Limit switch is on order. System is not heating at end of appointment

Performed furnace maintenance on 1999 Goodman system. Upon arrival tenant stated that system has been working OK and have repairs done recently in the summer they also bought the maintenance plan themselves and homeowner was unaware of this. Clarified and everything was understood by Mark once I gave him a call. Mark did decline safety inspection on heat exchanger. Once maintenance was complete I did find a few points of concerns that were addressed with Mark. 1. Indoor blower motor is leaking a significant amount of oil from its bearing and can potential lead to it locking up or overheating 2. Flame sensor was oxidized but was cleaned off at this time 3. Condensate line showed signs of debris inside of it and also found water damage around the unit. 4. Indoor blower air mixing cabinet is heavily covered in dust and debris due to 1 inch filters and inefficiently stopping dust particles. At this time Mark was notified and is completely aware of the condition of his 22 year old furnace.

Upon arrival informed client on how to wire system up. Client performed work and unit is now heating. Did not test cooling.