Winchester, CA

Upon arrival performed maintenance on AC system. System is older and is running high in electrical but is still below manufactured specs. Secondary motor control is in range. Indoor blower wheel is extremely dirty . Primary drain was clogged at p trap and at bottom of sink. Re worked drains, and added safety switch. System is now draining correctly. Primed drain with half a gallon of water. Refrigerant levels in range. Client replaced his filter. No models or serials, rubbed off. Client has a big hole in ducting might have a rat problem.

Upon arrival performed maintenance on AC system. System is older and is running high in electrical but is still below manufactured specs. Secondary motor control is in range. Indoor blower wheel is extremely dirty . Primary drain was clogged at p trap and at bottom of sink. Re worked drains, and added safety switch. System is now draining correctly. Primed drain with half a gallon of water. Refrigerant levels in range. Client replaced his filter. No models or serials, rubbed off. Client has a big hole in ducting might have a rat problem.

Arrived on site to perform AC maintenance on 2014 Amana system. Cycled system for cooling. Filters were just washed by homeowner. Verified proper cooling temperature split. April aire filter is no longer being used. Drain lines were not cleared as there was no clear out port left before trap when unit was installed. Checked outdoor unit electrical and components. Refrigerant pressures in range. Amp draws are within Range. Primary motor control is good as well as contact points . Capacitor value is out of range for hermetic. Homeowner has extras and will replace it. Pulled condenser motor and thoroughly washed out condenser coil inside and out. System is operational upon departure.

Replaced the exhaust draft motor under warranty.

Upon arrival found 1/4 systems down. Found fan motor belt had snapped. Installed new belts on all systems. Changed out all filters. Inspected electrical. Tested system. Unit is operational upon departure.

Arrived on site to perform spring tune up on a 4 year old unit. Condenser located in back of n side of home. No one was home as we met the realtor. Breaker was off to Ac and turned on. Cycled cooling. Washed condenser coil inside and out. Checked electrical compartment and components. Primary starter good. Secondary motor control is good as well. Fan motor is good and free of oil. Checked start up and run amps on compressor. Both are good and in range. Checked pressure and unit is idling good and steady just found air flow restriction as not enough air is entering unit due to the design of home and type it is. But is cooling at This time. Indoor unit but dusty but home is getting remodeled. No protection on unit and would recommend adding for protection. Cycled unit and since owner is not present. Would just email over report. Cycled unit and is operational upon departure. Realtor just turned off breaker as it was.

Performed ac maintenance on 2 year old system. Checked electrical components, inspected condensate line, checked filters and changed as customer provided, cleaned outdoor condensor coil and removed debris from unit. Tested capacitor and it is with in range. Checked refrigerant levels. Unit is cooling and operational upon departure.

Arrived on site to perform AC maintenance on two system condenser. Upon arrival homeowner stated that systems have been working properly and he has no questions at this time he advised me that any recommendations found on the system he would like emailed over. Perform full maintenance on both upstairs and downstairs unit and found a couple points of concerns. Downstairs- 1. Outdoor condensing fan motor has significant oil leakage coming from his bearing which will lead to it eventually failing 2. System Contained a Phased out Refrigerant called R22 which is no longer manufactured as of 2020 3. Starter showed signs of pitting and burn marks on contact points 4. System is not equipped with surge protection 5. No flood protection attached evaporator coil Upstairs- 1. System also contained phased out refrigerant 2. No surge protection 3. Recommend compressor saver kit is installed to reduce high amperage on start up 4. Starter had significant pitting Which can result in failure on start u

Arrived on site to perform spring tune up on a 2021 lennox unit outside. Condenser located on side of home. Clustered nonossuea San is working good. Washed condenser coil inside and out. Primary starter is good. Secondary motor control is and in range. Fan motor is good and free of oil. Checked start up amps and run amps and both are in range. Checked refrigerant pressure and are good and in range. Checked filter and is okay as client stated she dose replace herself. Found thermostat to be a bit hard to operate. Recommend replacing with a basic one for here to operate with out issues. No problems on unit. Cycled system and went over all findings. Client did hold off but did renew esa. Cycled unit and went over all findings. Cycled unit and is operational upon departure.

Tested upstairs furnace for operation. Added some extra vibration pads and added some padding at the gas line which was rubbing on the unit. Tested the equipment and spoke with Goodman tech support, the ohms and voltages are good. Recommending replacement of the inducer motor, compared to the downstairs this motor is much louder.

Job total is $25,504 client is responsible for $22,504. The Remaining balance will be paid by CA clean tech rebate for $3,000.

Preformed ac maintenances on 2010 amana system.

Upon arrival, started cleaning condenser. Removed large amount of dirt and dog hair from condenser. Tested electrical. Found compressor amping high. Condenser fan motor almost failing. Charge and temp split are low. Went into the attic. Blower motor was caked with dirt. Same with the heat exchanger and coil. System is over heating. Heat exchanger has heat marks from over heating. System has undersized return. Went over condition with client. Clients want to look at replacement options.

Monitored operation of system In cooling mode. Measured refrigerant pressures in both one and two zone cycles, recorded voltages and amp draws. Measured static pressure on single zone call. Contacted tech support, Bobby advising replacement of he outdoor heat pump.

Upon arrival performed diagnostic, client stated that there is really no airflow on kitchen side of home. System only has a 16 inch return duct. It is about 95 degrees outside. System is giving me a 17 degree split. Refrigerant levels are in range. System is just older & having trouble keeping up with such a demand. Advised moving forward with replacement options, get a system that can handle the triple digit days around this area. Client had someone coming out tomorrow to give options.

Upon arrival performed diagnostic, client stated that there is really no airflow on kitchen side of home. System only has a 16 inch return duct. It is about 95 degrees outside. System is giving me a 17 degree split. Refrigerant levels are in range. System is just older & having trouble keeping up with such a demand. Advised moving forward with replacement options, get a system that can handle the triple digit days around this area. Client had someone coming out tomorrow to give options.

Upon arrival performed diagnostic, client stated that there is really no airflow on kitchen side of home. System only has a 16 inch return duct. It is about 95 degrees outside. System is giving me a 17 degree split. Refrigerant levels are in range. System is just older & having trouble keeping up with such a demand. Advised moving forward with replacement options, get a system that can handle the triple digit days around this area. Client had someone coming out tomorrow to give options.

Upon arrival performed diagnostic, client stated that there is really no airflow on kitchen side of home. System only has a 16 inch return duct. It is about 95 degrees outside. System is giving me a 17 degree split. Refrigerant levels are in range. System is just older & having trouble keeping up with such a demand. Advised moving forward with replacement options, get a system that can handle the triple digit days around this area. Client had someone coming out tomorrow to give options.

Install is to include re piping the drain lines as well as furnace install. Also enlarging return ducts.

Upon arrival, started tune up of ac system. Cleaned condenser coils and checked refrigerant charge. Checked motors and start components. System checks out. Replaced filter with customer supplied filter. Flushed drain lines. Checked airflow. System is operational upon departure.

Upon arrival, started tune up on 2 Goodman systems. Both are 21 years old. Both condenser fan motors look bad. Leaking oil. One is over amping and failing. Refrigerant charge was low but system was still cooling. Contactor on downstairs unit is making a loud buzzing sound. Went into the indoor units and found both blower motors leaking a lot of oil. Should be replaced soon. Control modules have burn marks on them. Systems have poor flood protection on them. Went over condition of system with client. Emailed over repair options. Will follow up on Thursday.

Added iso pads to outdoor unit. Tested equipment on all modes and adjusted airflow. Adjusted refrigerant charge. Moved outdoor disconnect fuse box and relocated with emt and new high voltage wiring.

Customer stated the condenser was making a high pitched noise. I found that the noise only happened when one zone was open. When both were open, the noise would dissipate. To mediate this problem, I bled all the zone dampers 10% to relieve some pressure that was building up inside the unit so the compressor wouldn’t work so hard. This helped the condenser quiet down and the customers agreed it was much quieter.

Upon arrival performed heating tune up. Indoor motor is leaking a ton of oil. Indoor blower wheel had a lot of dust build up combined with rust. Return ducting is very undersized, would recommend enlargement to have more airflow pass through system so motor won’t over heat and leak oil. Ducts are just connected to system with nothing sealed around, system has been sucking in air and debree from attic. Tried to dust off burners but metal is stained from over time. System has no sediment trap for gas valve. Secondary motor control is out of range. Flame sensor looks very weak. Client is looking forward to premier + options. Has to speak over with the wife & will call the shop if wants to move forward with repairs. Also advised client should look into long term replacement options for system due to age & efficiency.

Upon arrival performed heating tune up. Indoor motor is leaking a ton of oil. Indoor blower wheel had a lot of dust build up combined with rust. Return ducting is very undersized, would recommend enlargement to have more airflow pass through system so motor won’t over heat and leak oil. Ducts are just connected to system with nothing sealed around, system has been sucking in air and debree from attic. Tried to dust off burners but metal is stained from over time. System has no sediment trap for gas valve. Secondary motor control is out of range. Flame sensor looks very weak. Client is looking forward to premier + options. Has to speak over with the wife & will call the shop if wants to move forward with repairs. Also advised client should look into long term replacement options for system due to age & efficiency.