Winchester, CA

Preformed furnace maintenance on amana heater

Upon arrival found system in a lockout. It was a high limit lockout. When both zones were open the system was fine. While only calling for 1 zone the temp rise would be more for what it’s rated for. Informed client he would need a 2 stage heater or a bypass duct. Tried to hook up second Wi-Fi stat to his phone. It was unsuccessful. Needs a new stat. Unit is operational upon departure.

Call Back- Gas valve had been left off, system is now working and operational.

Heating Maintenances Performed Upon arrival systems are working and operational. I began my maintenance in the attic by performing a duct leakage inspection. I then proceeded to the furnace units, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been checked, home owner stated they will buy some and replace them. Blower housing and wheel were inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of both indoor units, I found there to be no form of electrical protection on either units, recommend adding surge protection to both to ensure sensitive electrical components. Upon departure systems are working and operation

Performed AC diagnostic Aireflo condensing unit. Upon arrival homeowner stated that he has had other companies out and all of them have told them that the system needs to be replaced But Have given no reason to as of why. Proceeded to outdoor condensing unit and found that system was trying to start but the outdoor condensing fan motor was not spinning. Found that the dual secondary motor control has become defective on the fan side terminal. Installed new duel secondary motor control to test and system fired up, but unfortunately it is completely flat on R22 refrigerant. Client had mentioned that he noticed a hissing noise coming out of the unit and a big oil spot at the bottom by the compressor. Due to this being A major fault within the refrigeration cycle of the system this can become a costly process to try to repair a R 22 system. I was able to give a ballpark price to as far as what it may cost to replace the outdoor condensing coil and fully charge up the system with 8 pounds o

Upon arrival, started system tune up. Found unit was getting enough airflow. Install needs to come back and install new return. All mechanical components are operational at this time. Client said airflow wasn’t balanced. Need to add dampers to help block off airflow to bathroom.

Installation of 19 SEER Variable Speed Slim Line System with dual zoning.

Upon arrival started up heater to confirm its operational. Got attic access and started tune up. Checked heat rise and static. Both a little high. Pulled blower motor to get access to heat exchanger. Inspected heat exchanger and found hot spots on failure areas. Indicating not enough airflow and unit is over heating. While blower was pulled inspected cabinet. Found areas that were not sealed properly. Attic air is getting sucked into airstream. Inspected heating components. Found inducer motor to be over amping and will fail soon. Need to be replaced. Hot surface igniter and flame sensor are older and worn. They are operational at this time. But in the future should be replaced soon. There is no flood protection equipped on this unit. Sending estimate to replace inducer motor. Unit is operational upon departure.

Arrived on site to perform fall tune up on a 2019 carrier unit located in attic . Client stated no issues. Cycled heater on and was good. Filter were just replaced by client. Blower assembly and whee good. Motor and inducer motor are both good and in range. All safety switches are operational. Drain lines are clear but have no safety over flow switches and would recommend adding to primary or secondary pan to prevent over flow in attic. No protection in attic. Would recommend adding surge pro to protect electrical components and systems from electrical surges and power outages that can damage or even short out systems and components. Client did a aware and did declined recommended work at for now as he would have to budget for recommendations. Client os aware of how unit is running and conditions. Cycled system in heating and cooling to ensure system operating. System is operational upon departure.

Performed heating maintenance on Payne furnace. Tested all components and recorded diagnostics. Inspected controls and safeties. *did not measure temperature rise or run furnace past blower proving due to crack in heat exchanger, furnace breaker was left in the off position do you potential danger to indoor air quality in home*

Quality control check

Performed furnace maintenance on 2004 comfort maker heaters. Perform safety inspection on both heaters and electrical. During the maintenance they were a few points of concerns that were addressed with Gabriella. Found that both indoor blower cabinets were heavily covered in dust and debris due to the fresh air intakes and efficiently stopping Dust and debris from getting inside of the airstream and inside of the ducting. Recommended 5 inch filter installation for Significantly better filtration and stopping large dust particles from getting inside of the system. Will be rescheduling Call So that both wife and husband are home to go over options

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance in the attic by performing a duct leakage inspection. I then proceeded to the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been checked, does not need to be changed at this time. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of indoor and outdoor unit I found the starter to have signs of arcing as well as the blower motor and condenser fan motor to be over amping, recommend replacing to ensure reliability of the system. Also recommend looking at other options due to the age of the system. Upon departure system is working and operationa

Gas valve was left off .

Gas valve was left off .

Gas valve was left off .

Gas valve was left off .

Upon arrival performed heating Maintenance. Cleaned flame sensor, dusted off components. Tried cleaning furnace but home has sprayed insulation everywhere on top of attic. Furnace has spots from insulation that are hard to come off. Dusted off electrical components. Did not change filters, client likes 3m filters. Amperages throughout system are in range. Checked refrigerant levels, as client asked politely to check. Thermostats in working order. Blower wheel is beginning to collect a lot of dust levels. This can cause motors to over work and make wheel go off balance. Secondary motor control in range. Inducer motor amperages in range. Gas valve in working order. Circuit board and electrical connections good. Advised client there is better filtration to help with dust entering system. She was not interested. System is operational upon departure .

Upon arrival performed heating Maintenance. Cleaned flame sensor, dusted off components. Tried cleaning furnace but home has sprayed insulation everywhere on top of attic. Furnace has spots from insulation that are hard to come off. Dusted off electrical components. Did not change filters, client likes 3m filters. Amperages throughout system are in range. Checked refrigerant levels, as client asked politely to check. Thermostats in working order. Blower wheel is beginning to collect a lot of dust levels. This can cause motors to over work and make wheel go off balance. Secondary motor control in range. Inducer motor amperages in range. Gas valve in working order. Circuit board and electrical connections good. Advised client there is better filtration to help with dust entering system. She was not interested. System is operational upon departure .

Upon arrival performed heating Maintenance. Cleaned flame sensor, dusted off components. Tried cleaning furnace but home has sprayed insulation everywhere on top of attic. Furnace has spots from insulation that are hard to come off. Dusted off electrical components. Did not change filters, client likes 3m filters. Amperages throughout system are in range. Checked refrigerant levels, as client asked politely to check. Thermostats in working order. Blower wheel is beginning to collect a lot of dust levels. This can cause motors to over work and make wheel go off balance. Secondary motor control in range. Inducer motor amperages in range. Gas valve in working order. Circuit board and electrical connections good. Advised client there is better filtration to help with dust entering system. She was not interested. System is operational upon departure .

Upon arrival performed heating Maintenance. Cleaned flame sensor, dusted off components. Tried cleaning furnace but home has sprayed insulation everywhere on top of attic. Furnace has spots from insulation that are hard to come off. Dusted off electrical components. Did not change filters, client likes 3m filters. Amperages throughout system are in range. Checked refrigerant levels, as client asked politely to check. Thermostats in working order. Blower wheel is beginning to collect a lot of dust levels. This can cause motors to over work and make wheel go off balance. Secondary motor control in range. Inducer motor amperages in range. Gas valve in working order. Circuit board and electrical connections good. Advised client there is better filtration to help with dust entering system. She was not interested. System is operational upon departure .

Preformed furnace repairs on weatherking heater. Installed new exchanger due to original becoming overheated and cracked on tubes. Hot surface igniter replaced has 1 year warranty. Indoor blower was replaced has 1 year warranty. Evaporator coil was cleaned and sanitized, all debris was vacuumed out of primary pan and drain lines were cleared. System was tested in heating and cooling mode and is fully operational upon departure

Performed furnace Diagnostic on 2002 Bryant heater. Upon arrival Cole was originally set up as a Maintenance although initial testing on first start up showed that the system was actually overheating and not working properly at this time. Again system Diagnostic and during the troubleshooting I found multiple points of concerns that were addressed with Lori. 1. System high limit switches were tripping due to the heater overheating from a lack of airflow. These components are a safety inside of your furnace to prevent the system from getting too hot 2. Evaporator coil is heavily plugged up with Dust and debris which is adding in to the high static pressure/air flow restriction. This is another reason why the furnace is overheating 3. 1 inch filter was heavily restricted and blocked up with dust and debris, it needs to be swapped every one to three months. 4. Indoor blower motor has significant oil leakage coming from bearing and can we do it locking up or overheating. This is what is ca

Arrived on site to diagnose unit. Client stated he replaced thermostat and unit stopped working. He thinks it’s the fuse in The heater. Replaced fuse and now operational. Unit dose not have any protection and highly recommended adding surge protection to unit to protect from electrical surge and power outages that can damage or even short out systems and components. Client is aware and wanted to do minimum today. Client know unit is old but did declined recommended work at this time. Cycled unit and is operational upon departure. Client verified and is happy with today’s repairs.

Performed furnace maintenance 2009 Carrier furnace. Upon arrival client stated that they have not used the heat once yet But do it very rarely when it is cold. Advise client that I will be performing a safety inspection. During the maintenance there were multiple points of concerns that were addressed with Tim. 1. Pulled heat exchanger and found at three cells are cracked due to overheating and air flow restriction over the years. 2. Static pressure was reading 0.88 which is way over the normal limit required for the furnaces airflow to ensure proper operation and proper temperature range on heat exchanger. As a result of these it has caused the heat exchanger to crack. 3. Flame sensor is heavily oxidized and can cause failure on ignition if this worsens. 4. Blower motor is beginning to over amp and has oil leakage coming from the bearing which can lead to it locking up or overheating 5. Single secondary motor control is weak 6. System is not equipped with drip leg or surge protectio