Wildomar, CA

Tech arrived on site. Unit would cycle on and off. Found the thermostat would be calling but would still cycle off. Replaced thermostat and unit is cooling. Replaced filter. Customer signed up on membership.

Arrived on site to perform diagnostic on 8 year old trane system. Met with neighbor Ken and homeowner. Homeowner states that system is not cooling. The indoor unit kicks on, but the outdoor unit does not turn on. Cycled system for cooling, outdoor unit is unresponsive. Checked high and low voltage power coming into unit. System is not receiving low voltage command. Found a broken Y wire not carrying the command. Rewired condenser with spare wires within the wire coming from the furnace. Tucked wires into the condenser so they were no longer exposed outside. Cycled system, system is now cooling correctly. Checked electrical components everything is in range. Temperature split is in range and system is operating normally. Signed homeowner up on maintenance program. System is operational upon departure.

Tech arrived on site. Found the primary capacitor completely drained. Indoor cap was low. Fan motor was leaking oil. Replaced both caps and the unit began to cool. Compressor is drawing high amps. Recommend a booster kit. Unit is operational upon departure.

Arrived on site to perform maintenance AC maintenance on 2 11 year old York units. Cycled systems for cooling. Replaced 20x30 filter provided by customer, other filters were still clean. Checked outdoor units electrical and system components. Thoroughly inspected units and checked all components. Pulled off condenser fan motors and thoroughly washed out condenser coils inside and out. Concerns with units are as follows: 1. Systems both use r-22 refrigerant, which has been phased out and although it is still available, it is extremely expensive. 2. Compressors on both units are starting up with high amp draws 3. Upstairs compressor has high running amps and is close to going over the maximum allowed range. 4. Upstairs compressor is also not fully compressing the refrigerant correctly, and although the system is properly charged the pressures bounce around inconsistently. Compressor could possibly cause problems for this unit In the future. 5. Recommended replacing filters more often

Inspected system for faults and made repairs.

Inspected system for faults.

Performed AC diagnostic on York system. On my diagnostic client stated that they are moving out in a month inspector said that secondary drain line should not have water flowing from it. Found the primary drain line on evaporator coil was clogged and also clog at the sink where the P-trap is located. Performed a cut and clear and ran dry nitrogen through the PVC lines to clear any debris that may be causing restriction of flow. Also vacuumed up any Excessive water that was backing up inside the lines. Primed drain line after clearing and system is now properly Draining out of primary drain line

Upon arrival performed diagnostic. System is non operational upon departure. Found fuse top be bad. Replaced primary start component as it was pitted and burned badly. Hardstart kit in working order. Secondary motor control in range. System was reset tested and fully functional upon departure. Client is not ready to replace unit 3-4 years. Did not do membership today.

Upon arrival performed diagnostic. System is non operational upon departure. Found fuse top be bad. Replaced primary start component as it was pitted and burned badly. Hardstart kit in working order. Secondary motor control in range. System was reset tested and fully functional upon departure. Client is not ready to replace unit 3-4 years. Did not do membership today.

Upon arrival performed diagnostic. System is non operational upon departure. Found fuse top be bad. Replaced primary start component as it was pitted and burned badly. Hardstart kit in working order. Secondary motor control in range. System was reset tested and fully functional upon departure. Client is not ready to replace unit 3-4 years. Did not do membership today.

Upon arrival performed diagnostic. System is non operational upon departure. Found fuse top be bad. Replaced primary start component as it was pitted and burned badly. Hardstart kit in working order. Secondary motor control in range. System was reset tested and fully functional upon departure. Client is not ready to replace unit 3-4 years. Did not do membership today.

Performed AC maintenance on two system Goodman. Upon my maintenance we noticed a few things that were addressed with Rachel. Downstairs unit- 1. Measured refrigerant pressures and found that the system was under charged due to a potential leak or has been like this ever since it was installed. 2. Charged system up with approximately 4 pounds of R410a. System now has 8 degree sub cool with a 15° temperature split 3. Recommend that a leak dye/sealant is injected into the refrigeration cycle of the system to help us locate and pinpoint where it has originated from. Highly recommended in case system is low again 4. Cleaned off condenser coil was covered in dust and debris. Discussed system Condition with Mr. Montes and he wants refrigerant added into the system and he will get back to us if he would like us to inject a leak dye to help us locate the leak. System is now cooling with a 15° temperature split and 8° sub cool prior it was at zero. Upon departure both systems are cooling and

Arrived on site to perform diagnostic on a no cooling system. Client stated he has 2 systems and upstairs is not working. Recently had his small dog and he like to run around unit and he had ripped out some wires from unit to Edison box. Upon arrival found one of the low voltage wires not connected and not letting system turn on. Connected and secured wires and spade and system was operational. Client is aware of why system was not operational. Client did want to sign up on ESA plan. Cycled system to ensure system operating. Client is aware system is operational and cooling upon departure. Office will call client to get him on schedule when the time come. Client is aware and happy we came out to repair unit.

Replaced outdoor fan motor for upstairs system. Inspected attic space

Performed AC maintenance on 1 year old Lennox equipment. Cycled systems for cooling. Checked indoor and outdoor units electrical and system components. Thoroughly washed outdoor condenser coils inside and out. Replaced both Merv filters. Cycled systems. Systems are operational upon departure.

Tech arrived on site ready to do a combo tune up. Was advised that the concrete had been sealed so no ac tune up. Checked the heater and it fired up. Good temp split and static. No drip leg. Condensate pan had been rusted out. Flushed oil primary drain line. No back pressure. Primary pan most likely leaking, however did not see leak present at this time. Recommend replacing secondary drain pan.

Tech arrived on site. Found the system to be flat. Found the leak in the evap coil. Will follow up with estimates to replace.

Customer called saying no heat after last visit. Confirmed no heat. I Left ignitor unplugged on last visit. Fixed the issue system is running back to normal. Customer was understanding.

Performed AC maintenance on 2 27 year old Rheem units. Homeowner has lived in the home for about 10 years, has never done a maintenance on them. Has always felt like they just don’t cool the house down enough and they run for ever, stays away from using them too much because of the cost and they just don’t do the job. Cycled units for cooling. Checked indoor and outdoor units electrical and system components. Pulled condenser fan motors and washed outdoor condenser coils. Ran systems through point inspection. Concerns are as follows: 1. Neither unit is producing a proper temperature split and are not cooling effectively. 2. Indoor motors are starting to leak oil, blower wheels have slight dust build up. 3. Filters were dirty, downstairs unit filter was completely clogged, homeowner was unaware that there was a filter in that unit. 4. Outdoor condenser fan motors are leaking oil. 5. Refrigerant levels on both units are not up to manufacture specifications, which explains why units

Performed combo tuneup on a Comfort Pro system. Heating temperature split is 35 degrees. Flame sensor had light wear, it was cleaned and reinstalled. Ignitor is reading in range. Primary blower wheel had a piece of insulation stuck in the fins that I cleaned out today. Combustion blower is amping good. Duct runs are sealed and free from obstruction. A/C unit cooling split is good at 22 degrees. Refrigerant levels are in range. Condensate lines are clear. Compressor start and run amps are in range at this time. Both systems are not protected. System was cycled before departure.

Tech arrived on site, condenser were extremely dirty. Cleaned out both condensers. Electrical panels are super dirty. Cleaned them out as well. Found the downstairs condenser cap to be reading low. Most likely will fail this summer during the heat wave. Refrigerant charge is low and not cooling by 20. Both compressors on start up are high.

Arrived to perform combo tune up on 2020 lennox system. Client stated no issues. Washed condenser coil inside and out on both systems. Checked electrical compartment and components on both units. Both primary and secondary motor controls are good and in range. Fan motors are good. Amps draws are good on both systems. System are both cooling at 20 degrees. Cycled units. Inspected indoor units. Filters were okay and could last another 3 months and will need replacement. Blower assembly and motors are both good on units. Both inducer motors are good. All safety switches are operational. No protection on either system recommended adding surge protectors to protect units. Cycled system. Advised client of findings and recommendations with client. Client is aware of how system is running. Both systems are operational upon departure.

Performed AC diagnostic on 2005 Goodman condenser. Upon my diagnostic Mr. Vincent had stated the system hasn’t been working for the last couple days and was blowing hot air out of the supply vents. Further investigation shows that the compressor was locking out on lock rotor amps Which means the compressor was using too much power on start up causing it to go into a lock out. Found at the duel secondary motor control was reading at 4 MFD when manufacture specification is rated at 40. Installed new duel secondary motor control And condenser fired up. Upon measuring my amperage I found that the compressor was pulling at 20 A when the max amps is rated at 21. This is a major indication that the compressor is beginning to fail Due to the electrical windings becoming weak. Also found that contactor had major pitting and burn marks occurring on contact points due to the high amperage pull over time. System also contained R22 refrigerant which was completely Phased January 1, 2020. Power di

Upon arrivals on air conditioning system. Found outdoor motor to be leaking excessive oil and play on shaft, client requested to replace . Advised client disconnect is stuck, tried to fix it, ended up replacing with new one. Hardstart kit and secondary motor control in range. Primary start is in good condition. Programmed high efficiency motor. Cleaned outdoor coils. Replaced filter. System is operational upon departure - bad outdoor motor - replaced filter - hardstart in working order - secondary good

Upon arrivals on air conditioning system. Found outdoor motor to be leaking excessive oil and play on shaft, client requested to replace . Advised client disconnect is stuck, tried to fix it, ended up replacing with new one. Hardstart kit and secondary motor control in range. Primary start is in good condition. Programmed high efficiency motor. Cleaned outdoor coils. Replaced filter. System is operational upon departure - bad outdoor motor - replaced filter - hardstart in working order - secondary good