Wildomar, CA

Upon arrivals on air conditioning system. Found outdoor motor to be leaking excessive oil and play on shaft, client requested to replace . Advised client disconnect is stuck, tried to fix it, ended up replacing with new one. Hardstart kit and secondary motor control in range. Primary start is in good condition. Programmed high efficiency motor. Cleaned outdoor coils. Replaced filter. System is operational upon departure - bad outdoor motor - replaced filter - hardstart in working order - secondary good

Upon arrivals on air conditioning system. Found outdoor motor to be leaking excessive oil and play on shaft, client requested to replace . Advised client disconnect is stuck, tried to fix it, ended up replacing with new one. Hardstart kit and secondary motor control in range. Primary start is in good condition. Programmed high efficiency motor. Cleaned outdoor coils. Replaced filter. System is operational upon departure - bad outdoor motor - replaced filter - hardstart in working order - secondary good

Arrived on site to diagnose a no cooling 2003 unit. Condenser placated on side of home. Only upstairs is not working or cooling. Upon arrival spoke over with real estate agent and Matt seller of home. As they had just sold home and wanted to see what wrong with system and get it up and running for buy of home. Found out door unit not operational. Indoor unit is producing air flow. Filter dirty. Inspected out door unit electrical compartment and component. Found primary controls all burnt up and pitted on contacts points. Secondary motor controls is completely bad. Would recommend adding a compressor booster kit to help preserve compressor and run easier. Fan motor is very old condition and has been leaking oil from self wear of operation. Could fail due to conditions and oil that has been leaking in past. Advised client of findings. Did light maintenance on unit to see if that’s only issue of what is happening. Inspected indoor unit. Blower assembly has accumulated dirt over years o

Performed maintenance on a 2013 air flow furnace. The System is zoned. When running on 1 zone the static pressure is out of range. The temp split is also out of range. Duct runs look tight and free from obstruction. I am recommending using both zones simultaneously or getting rid of zoning all together. Amperage for combustion and primary blower Motors are in range. Ignitor is reading within specification. Flame sensor was cleaned and reinstalled. Condensate lines are clear. Performed maintenance on an Airflo condensing unit. Upon inspection the customer had told me the condensing unit had been moved recently in order to make room for pool equipment. The coils were heavily caked with dog hair and dirt. Coils were cleaned and panels reinstalled. Compressor startup amps are within spec. Fan motor is also in range. Secondary start motor is holding charge within spec for that component. The starter contact points are pitted and showing burn marks which are two signs of failure. The refrig

Performed furnace maintenance on 1985 Trane Heater. Upon my maintenance there were a few points of concerns that were addressed with Matthews 60,000 BTU FURNACE TRANE- 1. Inspected indoor blower motor and found massive amount of oil leakage occurring from bearing. Blower motor is used for AC, heating and fan mode it is at high risk of failing due to the amount of oil loss and cause the it to potentially lock up or overheat. 2. Preformed safety inspection On heat exchanger and found multiple points of corrosion and potential crack points although was not able to confirm any cracks were present at the moment. Recommended that he exchangers checked before every winter to insure the safety of everyone at home. 3. Indoor blower scroll wheel is heavily covered in dust and debris due to 1 inch filter inefficiently stopping dust particles. 4. Recommend filter swapped out every 1 to 3 months 5. Transformer was replaced in the past 6. Nox rods are completely Disintegrated. Discussed full condit

2 lbs of r410a and reflare copper fittings. Found fitting to be lose, declared tightened connections, added refrigerant. 90 day warranty on flares. City hall, cannot collect payment. Invoice .

2 lbs of r410a and reflare copper fittings. Found fitting to be lose, declared tightened connections, added refrigerant. 90 day warranty on flares. City hall, cannot collect payment. Invoice .

2 lbs of r410a and reflare copper fittings. Found fitting to be lose, declared tightened connections, added refrigerant. 90 day warranty on flares. City hall, cannot collect payment. Invoice .

2 lbs of r410a and reflare copper fittings. Found fitting to be lose, declared tightened connections, added refrigerant. 90 day warranty on flares. City hall, cannot collect payment. Invoice .

Arrived to find system not cooling properly. Upon inspection of the system found low charge. The system was charged in September without leak dye. The system has a leak and must be repaired before the cooling will work again. The evaporator coil is an all style coil and likely the cause, unable to determine without using nitrogen or leak dye. Tested electrical for the system and inspected fan motor. Controls look good but the fan motor is on its way out and should be replaced if the condensing system is going to stay in use. Washed condenser coil / left replacement filter. Measured refrigerant pressures and temperature splits.

Arrived on site to perform combo Tune up on a 2019 lennox unit. Client stated no issues just wanted to replace filter cause client has allergies. Furnace and Evaporator coil located in attic. Cycled cooling. Washed condenser inside and out. Checked electrical and primary and secondary motor controls are both good. Start and run amps are all good and in range. Fan motor is good and in range. System pressure are good. No protection on unit. Inspected indoor unit. Filter was dirty and clogged and client wanted to replace. Blower assembly is good. Motor is good and in range of amp draws. Inducer motor is good and in range. Evaporator coil is good at this time. Drain lines are good at this time System is cooling at 21 degrees and heating at 48 degrees. All other safety switches are operational. No protection on unit recommend adding a surge protector on unit to protect if from getting damaged from electrical surges and power outages that can damage or even short out systems and components

Installation of a 3 Ton Comfort Pro Mini-Split, and installation of a 208/230 circuit, lineset, lineset cover.

Performed furnace maintenance. Cycled system for heat. Verified proper heating sequence of operations. Recorded amp draws. Washed filter. Advised to insert a small mesh filter on fresh air intake. Indoor blower wheel is dirty. Indoor blower wheel has started leaking oil. Secondary motor control is within range. Cycled system, system is operational upon departure.

Technician arrived on site and found 1 gas line turned off from maintenance. Turned on gas and cycled heat for both units. Everything is working at this time.

Technician arrived on site and started performing one combo tuneup for a 5 ton HVAC system. Found the filter to be dirty and customer supplied a new one. Went through the entire safety checklist and everything looks great only thing that can be improved is to install new ducting as we reuse some of the old R-4. Went to the condenser and opened up the side panels, revealing the condenser coil was restricted with dirt. Brushed and clean the coils with chemicals until they were clean. Once clean started up the unit and checked all motor and bridges. All motor and bridges are good and charge is good. Unit is now operational for summertime

Technician arrived on site and started performing two combo tuneups. Started with the heaters and went through the 20 point inspection on each of them. All motor amperage is were within range and heat rise was good. All safety components checked out and had green checks across-the-board. Turned on the units to cooling and had the downstairs unit tripped on high head pressure after about five minutes of running. Found condenser coil‘s to be extremely dirty with dog hair. The coils were restricting airflow causing the unit to have high pressure. Removed all panels and brushed the coils off and cleaned them with water as per the data plate. The condensers are now ready to operate in the summertime.

Performed furnace maintenance on 1984 Intertherm heater. Upon my maintenance they were multiple points of concern that were addressed with Linda. Intertherm furnace- 1. Inspected indoor blower compartment and found large accumulation of dust and debris particles due to 1 inch filter not being washed out/swapped enough. 2. Found that indoor blower motor has oil leakage coming from bearing. If left in this condition. this can cause the motor to lock up or overheat From lack of lubrication. This motor is used for heating, cooling or just fan mode. 3. System had a 77° temperature rise which is concerning considering that the heat exchanger is only rated for 75°. This can affect the longevity of the heat exchanger which is a piece of metal that radiates heat and expands and contracts over the years. 4. System is not equipped with surge protection. 5. AC units did contain R22 Which is a phased out refrigerant as of January 1, 2020. Discuss full condition with Linda regarding the state

Furnace door became lose and door switch opened. Readjusted door switch and system is fully operational and heating upon departure

Performed two system 2002 Bryant furnace maintenance. Client stated that they are very conservative do not use heat too often. When they do temperature set at about 75°. Began my maintenance and noticed multiple points of concerns. Furnaces 1. Found that both indoor blower motors are leaking oil and can cause the motor to over heat or lock up if left in this condition. 2. Both single secondary mother controls are out of range and week due to motor using more power than needed 3. Static pressure on system was at 0.75wc indicating to me that the airflow is not adequate enough and the proper specification should be at 0.5wc. This number is higher due to undersized returns vents. 4. Flame sensors are oxidized. This can cause failure with the sensor for it being able to detect that the burners are on. 5. Heat exchanger had extremely bad Heat spots. This is due to overheating and air flow restriction causing the temperature to operate at a much higher temperature than it’s designed for.

Performed two system Goodman Heater Maintenance

Heating system maintenance. Serviced furnace, replaced filters.

Assessed home for condenser relocation estimate

Performed furnace maintenance on 2014 Lennox Heater

Arrived on site to perform fall tune up on a 2004 Bryant system. Furnace located in hall closet. Client stated no issues just wanted service. Cycled heating on and was operational. Found filter dirty and replaced filter. Blower assembly is accumulating dirt and debris and creating stress and wear on motor and work hard. Recommend a blower assembly cleaning to help reduce amp drawls and help motor run easier. Motor is good slight oil dried up from past 16 years of operation. Secondary motor control is not weak and border line bad from motor over working. Recommend replacing control before completely fails and system will then not produce airflow in heating or cooling. inducer motor is good and amp drawls are in range. Tried to pull and inspected heat exchanger and client did not want me to pull and inspected heat exchanger at this moment due to availability and would like for us to come back out some other time in the morning. Client is aware of safety inspection will not be performed a

Performed Furnace diagnostic on 2013 Goodman heater. Upon my diagnostic homeowner son had already open system up and found that igniter was broken. Upon starting diagnostic I read diagnosed system to find the problem is beginning at igniter so I added in a universal igniter and system sparked and is fully operational and heating up upon departure. Also signed up June for ESA plan To maintain heater and AC.