Wildomar, CA

Arrived on site to perform diagnostic on 2007 Goodman system. Home has 2 units. Unit that controls the right side of home is not cooling. Cycled system for cooling. Indoor unit kicks on normally, outdoor unit is unresponsive. Checked outdoor unit high and low voltage. System is recieving proper low voltage command as well as high voltage power. Found primary motor control in unit is completely toasted up, and is not allowing power to be transferred over to unit. Replaced primary motor control. Cycled system, system kicked on and started cooling. Amp draws are in range for compressor, motor was recently replaced and is in good condition. Replaced 1 inch filter inside home that was extremely restricted. Performed full evaluation of unit. Went over findings and recommendations with homeowner. Would like to take care of immediate repair and sign up on monthly maintenance program. System is operational upon departure. Took voided check for monthly maintenance program.

Installed relay and battery cap. Rewired wire at condenser. Customer paid 500 cash and the rest on card at first visit.

Performed AC maintenance on a 2020 carrier condenser. Indoor unit was unable to be checked due to blocked access. Homeowner was notified on maintenance visits to have this area clear. Filters were changed today. Cooling temperature split is good. Outdoor unit was chemically washed. Outdoor electrical components were tested and recorded. Refrigerant levels are in range. Customer signed up for scheduled maintenance with filters included. System is operational.

Performed heating maintenance on 10 year old Goodman system. Cycled for heat. Verified proper heating sequence of operations. Ran system through 20 point inspection checklist. Cleaned off blower and burner compartments. Noted any concerns. Went over findings and recommendations with homeowner. Cycled system, system is operational upon departure.

Performed service on a AC unit in Wildomar. Customer reports fan working but not condensing unit. Found low voltage short in the wiring. This was fixed and a maintenance schedule was setup. Ordering a few parts to help system last through the summer. Customer is aware of the frail condition of the system and is making plans to replace after this summer.

Quality control check

Performed maintenance on a pair of 2001 Bryant gas furnaces. Both heating temperature splits are ok. Front of the house unit motors are over amping or leaking oil. Ignitor is oxidized. Duct runs have a few rips and tears. Condensate lines are clear with no overflow switch. Safety check was performed on heat exchanger had significant heat spots that need to be addressed before the unit becomes unsafe. Bedroom unit is facing the same issues. Tech supervisor was at appointment to help with any questions. Customer states he wants to wait till system brakes to replace and not repair. Both systems are operational.

Two Rooftop Whirlybird Turbines. Roofer not included.

Performed heating maintenance on a 2013 Goodman high efficiency gas furnace. Customer reports light use of the heat this season. Units heating temperature split is low but in range. Sensors and switches were cleaned and tested. Filters are ok at this time. Electrical motors are amping high but still in range. Start control for primary blower is good. System could use electrical protection and drain lines should have overflow switch. System is operational at end of appointment.

Arrived on site to perform Ac tune up on a 8 year old Goodman unit. Unit located in back yard. Client stated no issues and his working. Cycled and is good. Filter was just recent washed and is good but advised they need to keep door open to allow air to enter unit. Indoor unit is older and is dusty and dirty as it’s older but still operating. Washed condenser coil inside and out. Cleaned and wiped down unit and electrical. Primary and secondary motor controls have been replaced last years and are good. Compressor booster kit is good as well. Checked start up amps and are good. Run amps are in range. Fan motor is still pro and okay as amps are good. Pressure are steady and cooling home. Outdoor Temperature was at 55 and it was cold but unit is cooling at 23 degrees. Advised no protection on unit and recommended adding surge protectors to protect systems from electrical surges and power outages that can damage or even short out systems and components. Cycled unit and went over all find

Arrived on site to perform fall tune up on 2 2 year old units. Both unit located in attic. Cycled both and good. Client supplied her own filter as she replaces every 6 months. Both blower assembly are good. Both motors are operating and in range. Both inducer motors are good. All safety switches are operational. Temperature rise was good on both units. Drain lines are clear. Clean blue flame. No protection on units recommended adding to protect from electrical surges and power outages that can damage or even short out systems and components. Recommend adding a whole house purifying unit to system as client dose like clean air in home and is always replacing filter every 3 months. Cycled both units and went over all recommendations and how unit is running. She is aware and did hold off for now as they would have to decide what they want to do. Client renewed ESA yearly. Cycled both unit and are both operational upon departure.

Customer to pay 90% of the job with 10% retained until after the completion of the project.

Arrived on site to perform fall tune up on a 2002 comfort maker. Cli Stated unit old but still heats. Cycled unit. Filter was replaced. Blower assembly is dirty. Motor is okay slightly oil but okay. Secondary motor control is bad and out of range. No sediment trap on gas line. Temperature rise was high and almost to max heat. All other safety switches are operational. Spark igniter. Flames sensor oxidized. Found static pressure to be high and not enough air entering unit. Advised to inspect heat exchanger for safety and they did approve. Inspected and found 3 chambers compromised and have cracks. Advised unit is not safer to run as it could risk combustion gas to enter home air stream. Advised would have to shut off gas or breaker. Client is aware and okay with so. Drain lines are clear but no safety overflow switches. Found evaporator coil to have a big hole from a rat that is chewed it up in past. Attic has rat infestation. No protection on unit and recommended adding so to protect s

Arrived on site to perform fall tune up on a 2020 unit. Client stated unit heat up good just makes a weird noise on start up. Cycled unit and found a little rattle noise. Found metal duct straps wrapped on B-vent are just tapping each other when the system turns on and it creates a bit of vibration. Showed client and separated straps and is good and did not make the noise any more. Filter was replaced. Blower assembly and motor are good. Inducer motor is good as well. Temperature rise is all good. All safety switches are operational. Drain lines are clear. Ducting is okay and good airflow. Found no protection on unit and recommended on new unit to protect from electrical surge and power outages that can damage or even short out systems and components. Went over all findings with client and she is aware and did hold off for now and stated she is sure if she wants to join but will call the office back if she would like to. Cycled unit to ensure system operating and is operational upon de

upon arrival performed maintenance on heating system. Indoor blower wheel is beginning to accumulate a lot of dust levels. Indoor motor and secondary motor control is in range. Advised client upgrading filtration will help system out more from keeping dirt. Circuit board and electrical connections good. Client still has a leak on coil, still needs to speak to his wife about replacement. Advised now is probably the best time for replacement. Customer will call Shop. System is operational. Did not add any upgraded to estimate list, client has other bigger problems before doing filtration.

upon arrival performed maintenance on heating system. Indoor blower wheel is beginning to accumulate a lot of dust levels. Indoor motor and secondary motor control is in range. Advised client upgrading filtration will help system out more from keeping dirt. Circuit board and electrical connections good. Client still has a leak on coil, still needs to speak to his wife about replacement. Advised now is probably the best time for replacement. Customer will call Shop. System is operational. Did not add any upgraded to estimate list, client has other bigger problems before doing filtration.

upon arrival performed maintenance on heating system. Indoor blower wheel is beginning to accumulate a lot of dust levels. Indoor motor and secondary motor control is in range. Advised client upgrading filtration will help system out more from keeping dirt. Circuit board and electrical connections good. Client still has a leak on coil, still needs to speak to his wife about replacement. Advised now is probably the best time for replacement. Customer will call Shop. System is operational. Did not add any upgraded to estimate list, client has other bigger problems before doing filtration.

upon arrival performed maintenance on heating system. Indoor blower wheel is beginning to accumulate a lot of dust levels. Indoor motor and secondary motor control is in range. Advised client upgrading filtration will help system out more from keeping dirt. Circuit board and electrical connections good. Client still has a leak on coil, still needs to speak to his wife about replacement. Advised now is probably the best time for replacement. Customer will call Shop. System is operational. Did not add any upgraded to estimate list, client has other bigger problems before doing filtration.

Arrived on site to perform fall tun rip on a 2 2004 airflow units. Furnace both located in attic. Client stated he lived in home 4 years and units running fine. Cycled both heaters and both okay. Filter both dirty and need replacement every 3 months at most. Both blower assembly are dirty form lack of maintenance and filter change out. Amps are in range. Inducer motor are in range just downstairs is almost at max and can fail. Temperature rise was really high and at max of 60 on downstairs upstairs was at 37 in range. Downstairs is heating high. Found air flow restriction on downstairs units as static pressure was above range on downstairs and was at max rate on upstairs. Advised client of findings and would like to do sad inspection check on heater and reason for of the findings. Client did approve to inspect downstairs due to high temperature rise and static. But did declined upstairs inspection. Unable to pull assistance with out messing up heater or having to charge labor to disas

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance in the attic by performing a duct leakage inspection. I then proceeded to the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been checked, does not need to be changed at this time. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of the indoor furnace I found the inducer motor to be seizing and over amping, as well I found the blower housing and scroll wheel to be heavily impacted with dirt and dust, I found the condensate to not have a safety switch to prevent flood da

Preformed 2 system furnace Goodman maintenance.

Performed heating maintenance on a 2013 Trane heat pump in Wildomar CA. System is heating really well with a 25 degree split. Filter is clean. Indoor coils are good and indoor blower is amping in range. The outdoor unit was chemically cleaned. Refrigerant levels were measured and are in range. Start motor for the outdoor fan is very weak, this is causing irreversible damage to the outdoor fan to leak oil, over amp, and over heat. The start motor was replaced today. All other components were measured and tested. The condition of the system was discussed with the homeowner. System is operational at this time.

Post job walk

Performed furnace maintenance on a Ducane horizontal furnace in wildomar. System is heating in range. Blower motor is leaking oil significantly. Inducer motor is leaking oil and over amping. I cleaned off sensors and switches. Duct runs are sealed. Condensate lines are clear. Heat exchanger inspection found bad hot spots which are signs of a weak component which can soon lead to safety issues. This needs to be addressed before a safety issue occurs. The condition of the system was discussed with the homeowner. Carlos scheduled an appointment to go over his options regarding equipment. System is operational at end of appointment.

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance at the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been checked, does not need to be changed at this time. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of the furnace I found the blower motor overamping due to the supply restriction, supply duct from furnace to attic plenum needs to be increased to lower amps and adjust air flow properly. I also found the furnace to be lacking a gas sediment trap and a condensate safety switch. Upon departure system is working a