Wildomar, CA

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance in the attic by performing a duct leakage inspection. I then proceeded to the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter have been changed at this time, home owner supplied. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of the system I found the blower housing and wheel to be heavily laden with dirt and debris, recommend having a blower housing pull and clean performed to alleviate extra wear on the blower motor as well as remove dirt from the air supply, would also

Tech arrived on site. Performed heating tune up. Heat rise and static are okay. Blower motor is new. Inducer motor is at max amps. Gas line flex is inside cabinet. B vent is loose and needs to be replaced.

Performed furnace Diagnostic on 21 year old Lennox heater. Upon arrival Matthew stated that on Saturday they tried to use the heater and noticed that the blower motor instantly turns on and nothing but cold air comes out. Began my diagnostic in the attic and found that the heater did have diagnostic codes indicating that the limit switches were tripped. After verifying that the safety switches are closed, blower motor was pulled out and heat exchanger was inspected for overheating. Found multiple heat spots on heat exchanger due to over heating from previous usage over the years. Circuit board also has burn marks and can lead more issues if damage worsens to brain of system. Last blower motor was heavily caked in dust and debris due to 1 inch filter inefficiently stopping dust particles. Ultimately Matthew was informed and aware of the bad condition of his 21 year olds furnace. Although it is still operational at this time, system is only designed for approximately 12-15 year life span

Installed blower motor and flame sensor. Cycled system. Unit is operational.

Taped the hole in the evaporator coil.

Tech arrived on site. Performed combo tune up. Started with the furnace. Cleaned electrical and inspected ignition components. Found no issues with the electrical. Ducts are older and undersized. Return is undersized for the system. Will cause problems long term with the system. Switched over to the AC. cleaned condenser coils. Checked electrical. Capacitor is getting lower but is still within range. Most likely failing because the return is undersized. Motor amps are good. Temp split is 23. Because of the undersized return. Checked thermostat for issues. It is not displaying outdoor temperature. No outdoor sensor on unit, it used info from the Wi-Fi. Tried different settings but the issue is with the thermostat. Unit is operational upon departure.

Performed furnace maintenance on a 2011 day and night gas furnaces. System is heating at max temp rise 60 degrees. Static pressure is high. Inspected heat exchanger through blower cabinet. Hot spots but no cracks. Flame sensor coating is wearing off. Blower wheel is clean. Combustion blower is in range. Primary blower is leaking oil all over the cabinet. Primary start control is in range. The condition of the equipment was discuses with the customer and a plan for repair was made. System is operational.

Switch out Honeywell thermostat with a sensi. Walked through app with customer. He had no further questions. System is operational.

0-down 18 Months 0% interest available If permits are declined -$850.00

Preformed furnace maintenance on 2020 Lennox system.

18 Months 0% interest available

Performed combo tuneup on a 2020 Lennox XC series system. Heating sensors and switches were cleaned and tested for correct operation. Gas valve was tested. Filter was very dirty, customer had a MERV 16 that was switched in today. Blower wheel is clean and spinning freely. Furnace components are amping in range. Outdoor unit was deep cleaned but very dirty causing a major air restriction. Outdoor components were measured and recorded, refrigerant levels are ok. System was operational at end of appointment. I am recommending a scheduled maintenance plan due to the condition I found the system in today. Homeowner was not present for the appointment. Checklist was left at the house and an email will be sent with a briefing of the visit.

Performed maintenance on Lennox Furnace. Systems heating temperature rise is 30 degrees. Sensors and switches were cleaned and tested. Filter is dirty, customer will be changing it themselves. Furnace electrical components are amping in range. Outdoor unit was very dirty and washed today. Refrigerant levels are good. Compressor and outdoor fan are in healthy condition. Homeowner was briefed on the condition of the system. System is operational at thus time.

Job walk

Upon arrival performed maintenance on Goodman heating system. Replaced merv 16 filter. Circuit board and electrical connections are in range. Recommended adding surge protection to keep system protected from power surges or outages. Dusted off all heating components and cleaned inside and outside of furnace cabinet. Amperages throughout system are in very good condition and range. UV light is in working condition.

Upon arrival performed maintenance on Goodman heating system. Replaced merv 16 filter. Circuit board and electrical connections are in range. Recommended adding surge protection to keep system protected from power surges or outages. Dusted off all heating components and cleaned inside and outside of furnace cabinet. Amperages throughout system are in very good condition and range. UV light is in working condition.

Upon arrival performed maintenance on Goodman heating system. Replaced merv 16 filter. Circuit board and electrical connections are in range. Recommended adding surge protection to keep system protected from power surges or outages. Dusted off all heating components and cleaned inside and outside of furnace cabinet. Amperages throughout system are in very good condition and range. UV light is in working condition.

Upon arrival performed maintenance on Goodman heating system. Replaced merv 16 filter. Circuit board and electrical connections are in range. Recommended adding surge protection to keep system protected from power surges or outages. Dusted off all heating components and cleaned inside and outside of furnace cabinet. Amperages throughout system are in very good condition and range. UV light is in working condition.

Replaced the low voltage fuse and isolated the wires that were shorted on the low voltage.

Inspected the system for faults and adjusted the airflow and gas pressure to lower the temperature rise.

Inspected system for faults and inspected equipment.

Returned to perform repair. Recharged system up with 7 pounds 11 ounces of R410A to bring system back up to normal operating pressures. Also added leak sealant and dye. Temperature splits are within proper range and system is cooling effectively. Went into attic and performed cut and clear on primary line, as well as cleared trap underneath sink which was extremely clogged. Opened coil to see if any leak dye showed itself as well as to clear primary trap. Need to return to perform leak inspection. Cycled system, system is fully operational upon departure. Fcc

Arrived on site to perform diagnostic on 8 year old Goodman system. Homeowner states his system is not cooling. This is a single stage unit zoned into two zones. Cycled system for cooling. Indoor unit turns on normally. Outdoor unit is completely Unresponsive. Checked for high and low voltage power. System is receiving proper high and low voltage power but contactor is not engaging. System is completely flat on refrigerant which is tripping the low pressure switch and condenser is not turning on. Performed visual leak inspection at condenser and indoor coil but could not locate leak. Bottom of drain pan is very rusted. Asked homeowner if they have had any condensation issues and he has had water leaking out the secondary drain line for as long as he can remember. Primary line must be clogged up. Went over findings and recommendations with homeowner. Homeowner chose to have unit recharged with dye and seal as well as cutting and clearing of primary line. Need to return to perform repai

Arrived on site to to diagnose unit not heating. Client stated we were just out to do maintenance and repairs and unit was working and after they left it didn’t heat up. Checked and found gas valve off. Urned it on and heater cycled on. Valve may have been left off when they left. Will. Or be charging client as it was left when repairs were made

System qualifies for promotional financing offers: 18 months no interest with payments or 12 months no payments no interest or 3 months no payments no interest the a reduced 6.99% Apr at 116 a month