Vista, CA

Technician arrived on site to do one combo tuneup on a four year old HVAC system. Started with the furnace and went through the entire safety checklist. Green checks across the board. 1 red check and it’s because there is no CO detector. It’s critical for safety that there is 1 installed in the house ASAP. could be life and death. Went onto the roof and found the condenser. No water access on roof and had to use sprayer on coils. Once coils were cleaned checked the electrical and start components. Everything is within range. Charge is good. Unit is ready for summer. Customer declined filter and will have filters for next inspection.

Arrived on site to diagnose a no heating system on a 2002 Rheem system. Client stated unit was not heating may have a intermittent issues. Has been happening since last tech was out. Cycled heating on and furnace was operational and heating. Filter was replaced but not the right size or have support to hold filter down. Cycled system 3 time and was operational and good temperature rise was at 58 degrees and still not over heating. All electrical connections were good and secured and safety switches are operational. Advised could be a bad board but since unit it not acting up or tripping or creating possibility of bad board or age is catching up with unit and is just really old. A lot of these areas of concerns were also brought up to client from previous tech. Client is aware of findings and areas of concerns that were also existing last visit. Advised client to consider full system replacement. Client is aware unit is really old and is considering replacement just gunna have to think

Performed AC/furnace maintenance on 2008 Armstrong system. On my maintenance there were multiple points concerns that were addressed with the homeowner AC- 1. Found the condenser fan motor had a oil leakage coming from bearing due to overheating and wear and tear overtime. If this motor feels this can cause complications in damage to the compressor and failure for cooling. 2. Condenser was heavily covered in dust and debris but was cleaned off this should be done yearly. 3. System was not equipped with surge protection 4. System contained R22 refrigerant which was completely phased out January 1, 2020. Furnace- 1. Found that the indoor blower motor had a oil leakage occurring as well and can cause failure in heating, cooling or just fan mode. 2. The secondary motor control has become weak due to fan motor using more power than needing 3. System temperature rise was at 67° exceeding the manufacture specification of 65 this is an indication of overheating and can cause complications wi

Quality control check

Customer is going to let me know which items he wants me to price out

Upon arrival performed maintenance on on 8 year old heating system. Dusted off entire system, electrical components cleaned. Cleaned flame sensor. Blower wheel beginning to collect some dust levels. Amperages throughout system very good. Circuit board and electrical connections good. Secondary motor control in range. Dusted off burners. - dirty blower wheel - temp rise good - amperages good - filter good - circuit board and electrical connections good System was reset tested and fully functional upon departure.

Upon arrival performed maintenance on on 8 year old heating system. Dusted off entire system, electrical components cleaned. Cleaned flame sensor. Blower wheel beginning to collect some dust levels. Amperages throughout system very good. Circuit board and electrical connections good. Secondary motor control in range. Dusted off burners. - dirty blower wheel - temp rise good - amperages good - filter good - circuit board and electrical connections good System was reset tested and fully functional upon departure.

Upon arrival performed maintenance on on 8 year old heating system. Dusted off entire system, electrical components cleaned. Cleaned flame sensor. Blower wheel beginning to collect some dust levels. Amperages throughout system very good. Circuit board and electrical connections good. Secondary motor control in range. Dusted off burners. - dirty blower wheel - temp rise good - amperages good - filter good - circuit board and electrical connections good System was reset tested and fully functional upon departure.

Upon arrival performed maintenance on on 8 year old heating system. Dusted off entire system, electrical components cleaned. Cleaned flame sensor. Blower wheel beginning to collect some dust levels. Amperages throughout system very good. Circuit board and electrical connections good. Secondary motor control in range. Dusted off burners. - dirty blower wheel - temp rise good - amperages good - filter good - circuit board and electrical connections good System was reset tested and fully functional upon departure.

Arrived on site to perform diagnostic on 20 year old Coleman furnace. Homeowner states that system is not heating. She had the gas company come out and they told her that the limit switches were bad. Informed that I would be doing a diagnosis to verify that they diagnosed it correctly. Cycled system for heat. Verified proper heating sequence of operations. System turns on the flames for about 1 minute, but the indoor blower motor never turns on. Checked for power and motor is recieving proper power. Checked secondary motor control and found it completely out of range, which is causing motor not to turn on. Spoke to son Rick over the phone and filled him in on findings. Because of the age of the equipment, did offer to do a safety inspection on furnace to ensure that it is safe to operate before doing any repairs. With Ricks permission went ahead and safety checked furnace. Pulled out blower motor and inspected heat exchanger. All 3 chambers of heat exchanger have really bad cracks on

Install Heatpump condenser on garage side of the home. Route refrigerant lines and electrical under the house to the indoor locations ( no exterior lines) Install Coleman downflow furnace in place of gas furnace. Modify cabinet for proper fitment. Relocate supply register in back TV room and abandon/seal supply under the couch. Financing available

Replace existing furnace with listed unit. Adapt to existing AC and ECOBee thermostat. Financing available 18 months 0% or several other options

Arrived on site to diagnose a 1987 Payne system located in laundry room closet. Client stated she shuts off system and unit does not turn off and fan keeps spinning. By passed thermostat and unwired thermostat wires off of board to see if system would shut off and still kept running. Jumped the heater directly and heater would turn on but fan would still turn on. Over all determined control board is bad and would need to be replaced to continue system Evaluation to ensure no other issues. Advised I would evaluate system in current condition and for safety. Found blower wheel is hammered of dirt. Filter was clogged and hammered. Motor is cover of oil and dirt from dirt entering system in past years. Found primary starter component was burnt up as well and some wires were burnt up from over heating from electrical. And heat exchanger was examined and found dimples to have a huge separation between them and it’s indefinite wear shows sign of high wear in past year and heat exchanger can

Performed AC/furnace tuneup on 2009 on amana system. Upon my maintenance there were multiple points of concerns that were addressed with the homeowner. AC- 1. Found that high-voltage relay low-voltage coil’s going out due to load vibration noise Coming off of coil. If this fails this can lead to the system not starting 2. Compressor was pulling high amperage on start up in recommend that compressor hard start kit is installed to the increase the life and reduce amperage on start up. 3. Condenser coil was extremely caked in covered in dust, Clean coil 4. System was not equipped with surge protection. Furnace- 1. Found inducer motor was over amping Due to bearing going bad and iscausing a loud noise during operation. 2. Furnace was also not equipped with surge protection 3. Flame sensor was slightly oxidize

Preformed furnace maintenance on 3 year old 96% Lennox heater. Upon my maintenance I noticed a few point of concerns that were addressed with the homeowner. Furnace- 1. System had no surge protection on both furnace and condenser 2. Furnace had no trap 3. 1 inch not filtering out enough dust and debris particles. This is causing build up within the system. Conducted leak search and found no signs of leak refrigerant leaks. Although did tighten core done on service port of suction side. Recommended that pressure are checked just before the summer to ensure no issues.

Cash discount applied

Performed routine fall maintenance on Coleman furnace in Vista.

Performed routine fall maintenance on Weatherking furnace in vista. Tested and verified correct operation of system and tested all safeties. Replaced air filter and made sure unit had good airflow. Recommend the following to keep system going long as possible 1. Adding sediment trap to system 2. Replacing hot surface igniter on system 3. Replacing transformer on system (Completed) 4. Adding SS2 switch for Drainline (Completed) 5. Replacing flame sensor 6. Upgrading thermostat

Upon arrival found system thermostat disconnected from wall. Reconnected thermostat and tested and verified correct operation of system. Checked the system and everything checked out good. Return is very restrictive and filter was really dirty before it was replaced yesterday. Flame sensor was also extremely dirty and needed to be cleaned. Recommended signing up for ESA to make sure system can last as long as possible. Also recommend upgrading filter and opening up return

Could not complete diagnostic due to heavy rain and furnace is outside of mobile home with nothing covering it. Need to reschedule.

Tested the system and found defective thermostat in the main lobby. System calibration is bad and cannot read the temperature in the room, thermostat was replaced. Programmed the new thermostat and tested both modes. Measured outlet temperature for both heating and cooling, disabled WiFi and scheduling.

Inspected furnace for faults. Found defective circuit board. Circuit board was replaced and system was tested. The high limit opened when the system runs on a single zone. Adjusted the gas pressure with both zones open and system is operating properly, would not advise running system on heat with one zone at a time.

Performed Heating tune up on front and back house 14 year old furnaces. Ran systems through inspection checklist. Went over findings and recommendations with homeowner. Stated they will be moving soon and wanted to see what condition they were in. Cycled systems, system is operational upon departure. Payment was collected through Lowe’s app.

Cash discount applied

Performed furnace diagnostic on 2006 Payne heater. Upon my diagnostic I found that circuitboard was a Display error code 13 which indicates that high limit or flame rollout has occurred. Upon further inspection I found that the indoor blower motor has failed along with the capacitor has become out of range. Also inspected heat exchanger and found multiple heat spots due to overheating over the years. Discussed the condition of furnace with homeowner And is aware that motor Needs to be installed So I can do a full inspection with system operational. Installed new blower motor and system was able to ignite and begin heating the home. Took static pressure readings and Found a total of 1.05 wc Considering that the specifications on the data chart is only rated for 0.5wc, Also found a 63° temperature rise which exceeded the max temperature of 60 on the data plate as well. Due to air restrictions and high static pressure this will result in a higher temperature within the heat exchanger hav