Vista, CA

Upon arrival installed sdg&e sensi predict.

Upon arrival installed sdg&e sensi predict.

Upon arrival installed sdg&e sensi predict.

Upon arrival installed sdg&e sensi predict.

Inspected furnace for faults. Found defective circuit board. Circuit board needs to be ordered from Goodman, matched model number with generally stocked universal boards and it is a specific model. Will call good a;Monday morning and reschedule repair.

Inspected furnace for faults

Arrived on site to perform fall tune up on a 2000 Goodman system. Furnace located in hall closet. Client stated no issues just has yet to get system serviced since system was replaced in 2000 by home warranty. Found system had 2 filter one in return vents and one inside the furnace itself. Advised they need to only have them in one place the return vents pt in the furnace as both filter are currently restricting airflow into system and could cause system to over heat. Found blower assembly and wheel dirty creating stress and wear on motor. Motor has been leaking oil and building up dirt and oil from past and the dirt that has entered system. Recommend replacing blower motor as it could fail in future due to conditions and how hard it’s working. Secondary control is good. Inducer is okay just a bit high amp drawls it still in range. Inspected heat exchanger and found 4 eyelids to be cracked from system over heating and not enough air flow passing heat exchanger. Advised client of fin

Performed FAU maintenance on 15+ year old heat pump unit. Met with the tenant. Cycled system for Heat. Checked indoor unit electrical and system components. Took temperature splits. Amp draws on indoor motor are high and close to over amping. Ductwork is in very poor condition. Was all sealed using regular duct tape and it is all starting to come off. Could not get age of equipment due to information being not able to read. Evap coil is clean. In heat, system is short cycling. It will heat for a couple minutes and then shut off. Checked outdoor unit electrical and systems components. Amp draws on compressor and condenser fan motor are high. Compressor is short cycling in heat and giving out. Condenser fan motor is leaking oil. Refrigerant pressures are still within Range. System is not working correctly and is working very inefficiently. Spoke with homeowner over phone and informed her of findings and recommendations. She just wants everything emailed, not looking to do anything at the

Performed heatpump package unit diagnostic on Lennox system. Upon my diagnostic I found the system was in lock out due high pressure within the evaporator coil. Further investigation showed that system was operational although operating at a very high liquid pressure, At about 500+ psi. Suspected that the filter may have been dirty although no filter was present indoor and within the package unit. This is caused the indoor evaporator coil to become layered in dirt and restricting airflow across the system this can cause a system to go off on high pressure due to low Airflow. Measure temperature split in system had about 130 Degree air temperature coming out of the supply vents. Recommended that a maintenance done on the system along with an evaporator coil cleaning along with filters being installed to prevent any further dirt buildup. Joseph said he’s going to check with his colleagues so that these repairs may be approved and a maintenance. Upon departure system is fully operationa

Installation of a Lennox 22 SEER Variable Speed one-to-one mini split 12K BTU System.

Replaced secondary motor control and flame sensor on carrier furnace. Also pulled and disassembled blower and performed full blower cleaning with chemical. Also installed furnace surge protector on carrier furnace in San Marcos. Tested and verified correct operation of system.

Inspected system for faults, diagnosed defective ignitor. Inspected system and ducting, tested blower and battery cap.

Performed diagnostic on 2 year old Goodman furnace. Homeowner states thermostat is blank. Checked for power at thermostat and found batteries were dead. Replaced batteries, thermostat came on. Cycled system for heat, system came on and started heating. Due to how thermostat is set up On wall, it would be hard to find a thermostat that fits due to wall having rock and was cut around thermostat perfectly. Thermostat would have to be same exact size so it does not look ugly on wall. Signed homeowner up on maintenance program. Next maintenance to be AC. Cycled system, system is operational upon departure.

Performed check up on 32 year old Payne unit. Home is for sale, and inspector had come out and said that the unit was not working. Homeowner wants everything checked to make sure it is operating normal. Cycled for cooling. System came on and started cooling normally. Refrigerant levels are in range and system is producing proper temperature split. Compressor amp draws and condenser fan motor amp draws are within range. Primary motor control is in good condition, and secondary motor control is within range for both compressor and fan motor. Pulled off condenser fan motor and thoroughly washed out condenser coil inside and out. System is operational and cooling as it should. Cycled system for heat. Verified proper heating sequence of operations. Temperature rise across heat exchanger is on higher end of allowed range. Ductwork is on the older side and is inefficient, but still operational. Filter is clean. System is operational. System is fully operational in both heating and cooling up

Installation of a Lennox 20 SEER Variable Speed XC20 Air Conditioner with Variable Speed SL280V Furnace with Pureaire PCO, Lineset, & Electrical. Check payment.

Examined the system for faults and replaced defective ignitor

Down-Flow System replacement with Comfort Pro A/C and Intertherm Furnace. Check Pricing is shown

Inspected furnace for performance. Straightened duct going to the fathers bedroom. Angled the fins at the grille to throw more air into the center of the room. Fixed the supply grille in the room which was loose.

Tested thermostat on the heat cycle and system energized. Measured temperature rise and checked thermostat scheduling. System must be set for “auto” to follow preset schedule. Found defective pressure switch failing to reset after heating demand ends.

Performance testing and service for furnace

Tested thermostat on the heat cycle and system energized. Measured temperature rise and checked thermostat scheduling. System must be set for “auto” to follow preset schedule.

Inspected the heater for faults. System run the burners for 5 minutes and kicks off before the blower can start, the system is overheating and the circuit board is not receiving a signal to start the fan. The ignitor and the circuit board are likely the cause of the issue. Cleaned the flame sensor on the spark ignitor and cleaned the washable filter. Tested the voltages and measured the blower run cap. System is 45 years old and the ac is from 98. Both systems are well past their lifespan and replacement is a great option for this system.

Performed AC diagnostic on November 3, 2020 due to the AC unit going off on high head pressure because of a restriction within the refrigeration cycle. Met Tracy today To discuss what options are available. Unfortunately there is no easy fix to the situation due to the restrictions being possibly located in the evaporator coil all the way down to the condenser compressor. Tracy stated that she just needs system cooling for new homeowners once they move in at the end of the month will call home warranty once system fails. Gave one option of removing Freon from the system so system will not kick off on high head pressure although this does not guarantee that this will fix the problem and cool. This is about a 75% chance it will work. Also discussed replacement options for AC and evaporator coil for a guaranteed solution. Tracy will speak with Matt and get back to us once they’ve made a decision on replacement or repair

Performed routine fall maintenance on Carrier Furnace in Vista. Tested and verified correct operation of system. Recommend (1) Replacing flame sensor. (2) replacing secondary motor control for blower motor (3) install surge protection for furnace (4) pull and do full blower motor cleanings (5) install sediment trap for the gas line.

Technician Findings: Upon arrival found system molex plug ground prong to be ripped out and not allowing voltage to the furnace. Replaced the molex plug in turn the system on. Systems blower motor turned on immediately without any call for fan or heating. This was due to the fan really on the control board being burnt out in not stopping the fan from turning on and off. Control board is bad and needs to be replaced. Also upon further inspection found Blower motor to be completely dirrty pulling higher amperage and with burnt wires on it. Also on further inspection found the high to low voltage transformer completely burnt up and should be replaced. Also found that the gas line is flexed into the gas valve which is not to California code and should be replaced with black iron piping with sediment trap. Overall due to the system being from 1975 and with extensive amount of repairs needed would not recommend band aiding the system and would recommend looking into long term options.