Vista, CA

Upon arrival performed maintenance on heating and cooling system. Checked refrigerant levels, amperages secondary motor control. Fuses all good. Washed out coil. Replaced merv filter. Cycled heat on and off multiple times, made sure system is going through operations. System is in range and ready to run. Client is very interested in purification system, would like to do a little bit more research.

Upon arrival performed maintenance on heating and cooling system. Checked refrigerant levels, amperages secondary motor control. Fuses all good. Washed out coil. Replaced merv filter. Cycled heat on and off multiple times, made sure system is going through operations. System is in range and ready to run. Client is very interested in purification system, would like to do a little bit more research.

Upon arrival performed maintenance on heating and cooling system. Checked refrigerant levels, amperages secondary motor control. Fuses all good. Washed out coil. Replaced merv filter. Cycled heat on and off multiple times, made sure system is going through operations. System is in range and ready to run. Client is very interested in purification system, would like to do a little bit more research.

Upon arrival performed maintenance on heating and cooling system. Checked refrigerant levels, amperages secondary motor control. Fuses all good. Washed out coil. Replaced merv filter. Cycled heat on and off multiple times, made sure system is going through operations. System is in range and ready to run. Client is very interested in purification system, would like to do a little bit more research.

Performed furnace tuneup on 1997 Goodman Heater. Upon my tuneup they were multiple points of concerns that were addressed with the homeowner Melody. 1997 GOODMAN FURNACE- 1. Measured systems temperature rise and found that he was exciting 75° with a temperature rise of 120. This is a major red flag considering that the system is tripping on high temperature 2. Heat exchanger on system it’s potentially cracked due to the incredibly high temperature rise and airflow restrictions. 3. System Had two filters one inside the return plenum and one at the return vent. This is also another cause of air flow restriction 4. Indoor blower motor had a oil leakage and can cause a potential lock up or overheating due to lack of lubrication 5. Air mixing cabinet was completely covered in dust and debris due to 1 inch filters in efficiently stopping dust particles 6. Flame sensor was heavily oxidized and can cause failure on start up in heating mode 7. Circuit board has slight burn and heat marks D

Arrived on site to perform to system AC Heavy maintenance. On my maintenance split system was non-operational due to 60 amp breaker being defective. Commended that breaker a swapped out so that we can get 240 V to the outdoor condenser to performing maintenance and evaluation to see what the condition is. Joseph will reach out to the elders And have an electrician come and repair the breakers. During my maintenance components checked out on Lennox package unit. 1. High voltage relay had about 65% pitting on contact points this can put it access the brakes for the system 2. Compressor amperage we’re all in range fan as well 3. Single and double secondary motor control had the proper MFD reading and show no signs of weakening at this moment. 4. Circuit board had no burn marks or heat spots 5. Measured the R410a refrigerant pressures. Pressures were at 10 sub cool which is in range. 6. System had a 20° temperature split 7. Indoor blower motor show no signs of oil leakage 8. Outdoor po

18 months 0% interest financing available

Placed condenser and pad. Welded new copper fittings with nitrogen onto lineset, de blurred lines and sanded connections. Pressurized system and held to check for leaks. Replaced shader cores. Purged nitrogen through both sides of system to remove dirt and copper shavings. Vacuumed system down to 250 microns to remove moisture and non condensables in the lines. Installed high voltage wiring and low voltage splices. Opened system stored refrigerant and tested cooling mode. Adjusted charge to achieve 7 degree sub cooling value. Measured indoor temperature split. Wrapped outdoor suction line with new insulation and uv resistant tape.

Upon arrival performed maintenance on air conditioning system. Indoor motor is leaking excessive oil, running high amperages. Very dirty blower wheel, recommend cleaning with replacement of motor. Circuit board and electrical connections good. Secondary motor control in range. Gas valve and shut of in working order. Refrigerant levels in range. Outdoor fan motor has bad bearing, does not spin freely, has a lot,of friction and stops quickly. Tested secondary motor control, passed test. Compressor kicking on with high start amps, could use a booster kit to keep amperAges low. Overall system is running high, could have high energy bills. System is still running, washed out coils. Sent over estimates to do a rejuvenation on motors. System was reset tested and fully functional upon departure. - blower motor leaking oil - condenser fan motor leaking oil - secondary motor controls in range - high amperages - cleaned coil

Upon arrival performed maintenance on air conditioning system. Indoor motor is leaking excessive oil, running high amperages. Very dirty blower wheel, recommend cleaning with replacement of motor. Circuit board and electrical connections good. Secondary motor control in range. Gas valve and shut of in working order. Refrigerant levels in range. Outdoor fan motor has bad bearing, does not spin freely, has a lot,of friction and stops quickly. Tested secondary motor control, passed test. Compressor kicking on with high start amps, could use a booster kit to keep amperAges low. Overall system is running high, could have high energy bills. System is still running, washed out coils. Sent over estimates to do a rejuvenation on motors. System was reset tested and fully functional upon departure. - blower motor leaking oil - condenser fan motor leaking oil - secondary motor controls in range - high amperages - cleaned coil

Upon arrival performed maintenance on air conditioning system. Indoor motor is leaking excessive oil, running high amperages. Very dirty blower wheel, recommend cleaning with replacement of motor. Circuit board and electrical connections good. Secondary motor control in range. Gas valve and shut of in working order. Refrigerant levels in range. Outdoor fan motor has bad bearing, does not spin freely, has a lot,of friction and stops quickly. Tested secondary motor control, passed test. Compressor kicking on with high start amps, could use a booster kit to keep amperAges low. Overall system is running high, could have high energy bills. System is still running, washed out coils. Sent over estimates to do a rejuvenation on motors. System was reset tested and fully functional upon departure. - blower motor leaking oil - condenser fan motor leaking oil - secondary motor controls in range - high amperages - cleaned coil

Upon arrival performed maintenance on air conditioning system. Indoor motor is leaking excessive oil, running high amperages. Very dirty blower wheel, recommend cleaning with replacement of motor. Circuit board and electrical connections good. Secondary motor control in range. Gas valve and shut of in working order. Refrigerant levels in range. Outdoor fan motor has bad bearing, does not spin freely, has a lot,of friction and stops quickly. Tested secondary motor control, passed test. Compressor kicking on with high start amps, could use a booster kit to keep amperAges low. Overall system is running high, could have high energy bills. System is still running, washed out coils. Sent over estimates to do a rejuvenation on motors. System was reset tested and fully functional upon departure. - blower motor leaking oil - condenser fan motor leaking oil - secondary motor controls in range - high amperages - cleaned coil

Diagnosed dirty battery contacts on pre-existing thermostat. Removed the thermostat and discovered there is no staging for his thermostat. Removed old thermostat and replaced with a Sensi with staging. Wired thermostat and programmed. Tested both heating and cooling. System is performing properly at this time.

Upon arrival performed maintenance on air conditioning. Circuit board and electrical connections good, recommend adding surge protection to keep electrical components safe. Blower wheel is beginning to collect some dust. Filter was extremely dirty, client provided replacement. Refrigerant levels in range. Amperages on compressor and fan motor in range. Opened up systemmand cleaned outdoor coils with green clean solution. Clients disconnect is broken. Secondary motor control in range. Will follow up with client with recommendations. System was reset tested and fully functional - dirty blower wheel - dirty outdoor coils - hardstart kit in working order - amperages good - standard filtration System was reset tested and fully functional upon departure.

Upon arrival performed maintenance on air conditioning. Circuit board and electrical connections good, recommend adding surge protection to keep electrical components safe. Blower wheel is beginning to collect some dust. Filter was extremely dirty, client provided replacement. Refrigerant levels in range. Amperages on compressor and fan motor in range. Opened up systemmand cleaned outdoor coils with green clean solution. Clients disconnect is broken. Secondary motor control in range. Will follow up with client with recommendations. System was reset tested and fully functional - dirty blower wheel - dirty outdoor coils - hardstart kit in working order - amperages good - standard filtration System was reset tested and fully functional upon departure.

Upon arrival performed maintenance on air conditioning. Circuit board and electrical connections good, recommend adding surge protection to keep electrical components safe. Blower wheel is beginning to collect some dust. Filter was extremely dirty, client provided replacement. Refrigerant levels in range. Amperages on compressor and fan motor in range. Opened up systemmand cleaned outdoor coils with green clean solution. Clients disconnect is broken. Secondary motor control in range. Will follow up with client with recommendations. System was reset tested and fully functional - dirty blower wheel - dirty outdoor coils - hardstart kit in working order - amperages good - standard filtration System was reset tested and fully functional upon departure.

Upon arrival performed maintenance on air conditioning. Circuit board and electrical connections good, recommend adding surge protection to keep electrical components safe. Blower wheel is beginning to collect some dust. Filter was extremely dirty, client provided replacement. Refrigerant levels in range. Amperages on compressor and fan motor in range. Opened up systemmand cleaned outdoor coils with green clean solution. Clients disconnect is broken. Secondary motor control in range. Will follow up with client with recommendations. System was reset tested and fully functional - dirty blower wheel - dirty outdoor coils - hardstart kit in working order - amperages good - standard filtration System was reset tested and fully functional upon departure.

Arrived on site to diagnose a system that is not shutting off the fan on a 2003 unit located in attic. Client just moved in 6 days ago and recently and she stated systems heater turned on and fan hasnt shut off since. Found out his fan had turned heater on. Inspected unit and found furnace to not be giving any error codes. All safety switches are good and have voltage and continuity. Advised client there is 2 zones on this system and zone one was calling for heat and fan to operate. . Inspected whole house and found another thermostat down stairs in master that has been set to On for heating and fan motor on. Cycled system in cooling and heating to ensure and replaced filters. Recommend client to join a maintenance plan to keep systems operating and best performance and extend life of system. Went over finding with client and she is aware what was wrong with system. Client did declined recommended work at this time. Wants to look over her home warranty and see what they over with there

Preformed cleaning on evap coil and condenser due to coils becoming covered in dust and debris from no filter. Recommended maintenance plan to keep system at standard. Upon departure system was tested and is fully operational.

Performed tuneup on a Lennox heat pump. Indoor Blower was amping in range. Duct runs are tight and clear from any obstructions. Condensate lines are clear. System is equipped with a merv cabinet. The merv filter that was installed is a 20x20x5 which then cabinet is measured for a 20x25x5. This is causing the air handler coil to be heavily clogged on the left side of the coil where the open gap is. I am recommending a coil cleaning to solve that issue. The outdoor unit can amperages are in range. The secondary motor control is within spec. The outdoor unit starter is very loud and should be monitored. The resistance on the starter is still within range. The customer has been notified of the units condition. System was tested before departure.

Installation of a Comfort Pro X-Series 19 SEER Variable Speed Air Conditioner with Variable Speed Furnace and 2 Stage Gas Valve. Damper, Plenums, Registers, were deducted and Promotional UV Light was added. Check Pricing is shown and will be collected end of day of installation.

Performed tuneup on a Lennox heat pump. Indoor Blower was amping in range. Duct runs are tight and clear from any obstructions. Condensate lines are clear. System is equipped with a merv cabinet. The merv filter that was installed is a 20x20x5 which then cabinet is measured for a 20x25x5. This is causing the air handler coil to be heavily clogged on the left side of the coil where the open gap is. I am recommending a coil cleaning to solve that issue. The outdoor unit can amperages are in range. The secondary motor control is within spec. The outdoor unit starter is very loud and should be monitored. The resistance on the starter is still within range. The customer has been notified of the units condition. System was tested before departure.

Performed furnace maintenance On Goodman system. Temperature is on system checked out properly for furnace. Recommended that secondary float switch is installed to prevent any future flood overs that may occur. Discuss for condition with Bill and system is . functioning properly at this time. Reset and tested system upon departure heating is fully operational

Arrived on site to diagnose a no cooling system. 2009 lennox furnace and a 1988 condenser unit. Client stated he moved in 2017 and has had some issues then but had home warranty come and out told him he could replace the low voltage thermostat wires and he replaced and shortly after his dog chewed up wires again and unit has been down for about 2 years as they don’t use system a lot due to weather they have out here. Inspected system found no filter used and has never had once since clients moved in. Found low voltage was not getting to out door unit. Would have to do a low voltage repair to condenser unit and add in new thermostat to electrical compartment to unit. Advised client would have to test system out to get system operational and then I could evaluate system over all. Client is aware unit is really old and is considering system replacement. As client stated he is aware of age, issues and conditions and would rather not do repairs on old unit and get pricing on replacement.

Installation of a 2 Ton Mini-Split In I.T. Room with direct swap of wall mounted system and condenser right over it, crane services will be included.