Vista, CA

Arrived on site to perform diagnostic on ducted mini split unit. Upon arrival client wanted to swap original thermostat out with smart Wi-Fi thermostat. Low-voltage wire connection was snipped and was unconfigurable with thermostat at this time. Advice Klein the thermostat will need to be installed in there will be a charge due to original one being damaged. Klein would like to see if we can just do a Wi-Fi mini split thermostat.

Performed service on a Rheem/Goodman condenser. Customer reports unbalanced airflow from top and bottom levels of the home. Inspected ducting to find no dampers. This is hindering any real balancing adjustments to be made. The ducting is in very poor shape, major rips and tears on the duct runs. This is losing efficiency and adding to the airflow problems. I found the return grills to be blocked off by the framing of the home. This is causing air noise and could be starving the system of air. Customer was only curious to see if a small adjustment could be made so I made some vent adjustments downstairs. Advised the customer dampers will help with adjustability however due to the duct condition a replacement will be best option. She said she will wait out this summer and schedule a better time for duct estimate.

System totals to $11,386 - Client is only liable for payment of $8,386 as Tech Clean California Rebate will cover remaining $3,000 balance. Installation of Condensers/ Wallmount units, Linesets, Eletrical runs.

Performed service on a 1989 janitrol system. Customer reports leaking coming from the furnace area. Homeowner cleared condensate lines himself however the leak still persisted. Upon inspection I found the lines were clear of debris. The evaporator coil is completely rusted out. This is causing the leak to enter the heat exchanger and down to the blower housing. This pan needs to be replaced which is only 1 component that needs attention. The customer has high energy bills and wants to discuss equipment options.

Arrived on site to perform AC diagnostic on high pitch noise coming from outdoor condensing unit. Upon arrival Greg stated that the system is working fine in blows out cold air although when the outdoor fan turns on it begins to Kriti hi screeching noise. Proceeded to outdoor unit and found that everything was operational and unit was making loud noise took fan motor off the top of the condenser and inspected and found that the Bearing is defective. Inspected electrical components and found does secondary motor control is becoming low on compressor side terminal and high-voltage distributor has burn marks on it. System is still operational at this time the client is interested in system replacement and wants to get multiple bids before he gets Our price. He also may just replace the motor himself and was looking up a couple different motors online. Ultimately client will give us a call and upon departure system is fully operational and cooling

Upon arrival client said indoor unit was frosting up. Filters are good. Coils are clean. Charge was okay. It’s possible that during the hottest days the pressure decrease and it will freeze. As of now charge is good. Would check with installing company to see if and labor warranty. Unit is operational upon departure.

Upon arrival, performed tune up on system. Indoor blower motor is failing. Rusting out and close to max amps. System is currently over heating. Causing stress on the heat exchanger. GAS LINE IS LEAKING GAS. TURNED GAS OFF AT SYSTEM. client moved forward with repair to replace gas line.

Collected $1000 deposit. Balance due upon completion

Replaced S 30 hub and thermostat under warranty. System is now fully operational in heating and cooling upon departure. Error code is no longer popping up

Arrived on site to perform furnace maintenance on 2020 Lennox heater. Upon arrival Vincent states that the system has been working properly Although he was a bit concerned about the emergency pan filling up with water in the summer because it happened previously in the past. Performed full maintenance and safety inspection on unit. Temperature rise is within range. Amperages for inducer motor and indoor blower motor are in range at this time. Vincent will be ordering a new filter needs to be swapped as soon as possible. Flame sensor was cleaned off and hot surface igniter is in the range of resistance. Emergency pan showed signs of rust although no water present at this time and inside the primary and secondary line. Vincent will keep an eye on emergency pen to ensure no water fills up inside of it in the summer. Ultimately Maintenance checked out properly and client is aware of current condition.

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance in the attic by performing a duct leakage inspection. I then proceeded to the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been changed at this time. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon departure system is working and operational.

Preformed furnace maintenance on 2015 Maytag heater.

Upon arrival performed diagnostic. Found electrical breaker to be bad. System is non operational.

Upon arrival performed diagnostic. Found electrical breaker to be bad. System is non operational.

Upon arrival performed diagnostic. Found electrical breaker to be bad. System is non operational.

Upon arrival performed diagnostic. Found electrical breaker to be bad. System is non operational.

Check System Static Pressures Check all Safety and Limit Switches Clean Condenser Coil Duct Leakage Inspection Remove Debris from the Condenser Check Refrigeration Pressures Perform Visual Inspection and Clean Service Panel Measure Starting Amperage of the Compressor Tighten Electrical Connections Measure System Amperage and Voltage Flush Condensate Drain Lines Measure Temperature Difference Vacuum Furnace Return Air Grille Clean in Place Blower Compartment Inspect Blower Wheel for Proper Balance Monitor Air Purification System Apply UV Protective Coating on Condenser Perform Energy Usage Calculation Test Condenser Pressure Switches Check Thermostat for Proper Operation / Calibration

Arrived on site to perform AC maintenance. Cycled system for cooling. Checked indoor unit electrical and system components. Temperature split is in range. Merv filter is not horrible but somewhat dirty. Will has extras and will be replacing it soon. Checked outdoor unit electrical and system components. Took system amp draws. Primary motor control is slightly burnt and pitted. Secondary motor control is out of range for compressor. Cleaned outdoor unit. Went over findings and recommendations with homeowners. Replaced secondary motor control, renewed maintenance program. Cycled system, system is operational upon departure.

Arrived on site to find system not communicating with s30. Reset system by breakers system began cooling for approximately 2 minutes then s30 resets by its self and repeats this multiple times. Proceeded to indoor FAU and found the circuitboard had no error codes present on Diagnostic indicator. Measured DC volts leaving smart hub and found that it is losing its 12 volt output. This indicates that the smart hub is defective and will need to be replaced. Advised client part is covered under warranty and labor. Will order part from Lennox and will contact when it is in hand for scheduling. Upon departure system is non operational.

Preformed ac/furnace maintenance on 2021 Lennox system. Maintenance check out properly. Filter was swapped and should be checked every 6 months. Client would like to sign up on maintenance plan but would like to speak with wife and he is moving jobs right now so would like us to give him a call 2 weeks from now. System is working in the proper range. Unit was reset and tested upon departure.

Arrived on site to diagnose a leaking water on a brand new Install that was just installed. Client just got done remodeling home and found floor wet. Client stated unit was not used but looked into return and found copper lines wet. Was unsure where water was coming from. Removed other retune and went into return to inspect all the lines. Had client turn on main water supply line that enters home and copper lines started leaking from underground. Took a video and advised client and he did see it leaking. Advised call a plumber to see what they can do. Client is aware and happy we came out. Advised no charge for today. Advised to keep main line off to prevent over flow in home. Client is aware.

Upon arrival performed maintenance. Opened up system and cleaned coils out. Tested voltages and amperage’s. Wiped down air handler, system had a ton of rat dropping in attic and on top of unit. Client feels like her filter got dirty to fast, has put it in there for 5 months. Advised when leaving doors open all the time, gusts of winds make there way in. Could not test refrigerant levels due to no clearance on valve for gauges. Temperature split is 20. System is operational upon completing.

Upon arrival performed maintenance. Opened up system and cleaned coils out. Tested voltages and amperage’s. Wiped down air handler, system had a ton of rat dropping in attic and on top of unit. Client feels like her filter got dirty to fast, has put it in there for 5 months. Advised when leaving doors open all the time, gusts of winds make there way in. Could not test refrigerant levels due to no clearance on valve for gauges. Temperature split is 20. System is operational upon completing.

Upon arrival performed maintenance. Opened up system and cleaned coils out. Tested voltages and amperage’s. Wiped down air handler, system had a ton of rat dropping in attic and on top of unit. Client feels like her filter got dirty to fast, has put it in there for 5 months. Advised when leaving doors open all the time, gusts of winds make there way in. Could not test refrigerant levels due to no clearance on valve for gauges. Temperature split is 20. System is operational upon completing.

Upon arrival performed maintenance. Opened up system and cleaned coils out. Tested voltages and amperage’s. Wiped down air handler, system had a ton of rat dropping in attic and on top of unit. Client feels like her filter got dirty to fast, has put it in there for 5 months. Advised when leaving doors open all the time, gusts of winds make there way in. Could not test refrigerant levels due to no clearance on valve for gauges. Temperature split is 20. System is operational upon completing.