Vista, CA

Performed combo maintenance. Inspected and tightened electrical components on furnace- cleaned flame sensor Checked filter- and changed adjusted zoning, inspected register as there was a flapping noise due to some plastic and tape from the duct. This was removed and resolved the noise. Inspected Temperature split was at 20 degrees.inspected and cleared condensate lines, system had flood protection.Checked outdoor electrical components, determined one of the wires had become pinched with a screw at the time of install. Causing the wire to short- I spliced and repair the wire. measured Washed and cleaned outdoor condenser coils. Removed debris from bottom of the condenser and cleaned and removed debris from electrical cabinet. System is cooling and operational upon departure

Performed AC maintenance. Inspected and tightened electrical components. Checked filter- and changed customer pays additional for filter replacement . Inspected Temperature split was at 20degrees.inspected and cleared condensate lines, system had flood protection.Checked outdoor electrical components, measured capacitor within range. Washed and cleaned outdoor condenser coils. Removed debris from bottom of the condenser and cleaned and removed debris from electrical cabinet. System is cooling and operational upon departure.

Performed AC maintenance. Inspected and tightened electrical components. Checked filter- recommended changing -customer is going to change . Inspected ducting to ensure proper airflow. Temperature split was at 20degrees.inspected and cleared condensate lines, system had flood protection drain pan and float switch. Checked outdoor electrical components, measured capacitors both within range however there are signs of low voltage needing to be repaired- wire melted at spade fitting and contact on capacitor (I recommend replacing both contactors with Turbo Start component . Checked both contactors and recommended replacing as they are pitted and could potentially fail causing damage to other components. Assist kit is also with in range. Washed and cleaned outdoor condenser coils. Removed debris from bottom of the condenser and cleaned and removed debris from electrical cabinet. System is cooling and operational upon departure.

Upon arrival, started ac tune up. Condenser is on roof. Cleaned coils and checked electrical. Charge is good. No issues found. Went into attic and changed filter with customer supplied one. Flushed drain lines. Checked static pressure. No issues found. System is operational upon departure.

Arrived on site to perform AC diagnostic on 2016 AC pro condensing unit. Upon arrival Nick stated that we were out approximately one week ago for the breaker not working properly and now after letting it run he has noticed that it is not cooling off the house properly. Started off at outdoor unit and found that it was significantly low on R410a refrigerant charge. This is an indication that there is a leak somewhere within the refrigeration cycle of the system. Advised client that system is low enough to perform nitrogen test to help locate refrigerant leak. Unfortunately nitro test was performed and leak was not detectable even with nitro at this time. It is unknown where the location of the leak is at and advised client that we will be injecting a leak dye/sealant into the system with a full charge up. Once the charging process began I found There was a refrigerant restriction present due to abnormally low suction pressure and extremely high head pressure after adding an only 1 pound

Arrived on site to preform ac maintenance on 16 year old condenser

Arrived on site to perform AC maintenance on two-year-old Linux system

Arrived on site to perform leak repair. Nitro test and vacuum was complete system held pressure properly. Charged system up with a 1 pound and a half. System is operational and cooling with a 20° split upon departure

Arrived on site to perform AC diagnostic on 2019 condensing unit. Upon arrival Tyler stated that action air air conditioning was just out and found a refrigerant leak on the welds coming into the condenser outside. They have already injected and leaked dye into the system and have pinpointed that it is on one of the welds that was improperly brazed. Verified with UV light and found location of leak. Advised client that system is still slightly low on charge and may need to add 2 pounds in or more. System will be completely vacuumed out and pressurized with nitrogen to ensure no more leaks are present in the system. Once this is done it will be fully charged up. Presented leak repair option to Tyler and he has approved this and will be returning tomorrow at 8 to 10 AM. He will consider maintenance plan but needs to cancel his action air maintenance plan.

Jimmy got to customer home - customer just had exterior of house painted & did not want Jimmy to wash down the condenser risking new paint job

Tested thermostat on cooling mode. Tested different settings and system appears to be working at this time. If the problem persists the thermostat will be replaced under warranty.

Technician arrived to inspect unit and get information. Was able to get model serial for one unit, the other unit only had the serial number available. They are the same unit though.

Removed the secondary drain line which was connected to the secondary drain pan with a switch.

Upon arrival performed diagnostic, found system to not have any power at system. Found breaker to be on wrong part of terminal for circuit breaker.only 1 leg was touching. Could not take off gold refrigant caps. To check refrigerant. Client is calling company that installed. If not will call us back. System works just doesn’t cool now.

Upon arrival performed diagnostic, found system to not have any power at system. Found breaker to be on wrong part of terminal for circuit breaker.only 1 leg was touching. Could not take off gold refrigant caps. To check refrigerant. Client is calling company that installed. If not will call us back. System works just doesn’t cool now.

Upon arrival performed diagnostic, found system to not have any power at system. Found breaker to be on wrong part of terminal for circuit breaker.only 1 leg was touching. Could not take off gold refrigant caps. To check refrigerant. Client is calling company that installed. If not will call us back. System works just doesn’t cool now.

Upon arrival performed diagnostic, found system to not have any power at system. Found breaker to be on wrong part of terminal for circuit breaker.only 1 leg was touching. Could not take off gold refrigant caps. To check refrigerant. Client is calling company that installed. If not will call us back. System works just doesn’t cool now.

Upon arrival performed AC tune ups, refrigerant levels are in range. Replaced filter client provided. Indoor coil is very clean. Dusted off return registers. Washed condenser coils. Checked primary and secondary starter. Circuit board & electrical connections in range. Hardstart kit in working order. System is operational upon completion. Client approved renewal.

Upon arrival performed AC tune ups, refrigerant levels are in range. Replaced filter client provided. Indoor coil is very clean. Dusted off return registers. Washed condenser coils. Checked primary and secondary starter. Circuit board & electrical connections in range. Hardstart kit in working order. System is operational upon completion. Client approved renewal.

Upon arrival performed AC tune ups, refrigerant levels are in range. Replaced filter client provided. Indoor coil is very clean. Dusted off return registers. Washed condenser coils. Checked primary and secondary starter. Circuit board & electrical connections in range. Hardstart kit in working order. System is operational upon completion. Client approved renewal.

Upon arrival performed AC tune ups, refrigerant levels are in range. Replaced filter client provided. Indoor coil is very clean. Dusted off return registers. Washed condenser coils. Checked primary and secondary starter. Circuit board & electrical connections in range. Hardstart kit in working order. System is operational upon completion. Client approved renewal.

Arrived on site and performed AC maintenance on Lennox system.

Arrived on site and performed AC Maintenance on 2001 rheem condenser. Upon arrival Susan stated that she’s had no issues with the system. Perform system clean out on outdoor condenser coil. All electrical components checked out properly Besides starter with heavily burnt contact points. System contains a phased out refrigerant called R22 which is no longer manufactured as of January 1, 2020. Pressures are in range at this time. Amperage is for compressor Are beginning to get high But OK at this time. Condenser fan motor shows no signs of oil leakage. Cleaned out condenser where it looked like a rat had nested in. Discussed full maintenance with client and she is aware of current condition. She will be buying filters herself and swapping them out. Client would like to renew maintenance plan at this time in systems fully operational upon departure.

Performed AC and heating maintenance on heat pump. Inspected electrical components. Inspected ducting. Clean outdoor condenser coil and remove debris from bottom of the unit. Checked filters customer will change. System does have drain pan and float switch system is zoned. System is operating upon departure

Replaced the thermostat control and wire harness for the ducted mini split system. Tested equipment and ensured proper operation. Replaced the thermostat control and wire harness for the ducted mini split system. Tested equipment and ensured proper operation.