Vista, CA

Upon arrival started ac tune up. Cleaned out condenser coil. Checked electrical and pressures. Motor amps are okay. Pressures are good. Temp split is 18/20. Static pressure is high indicating a lack of airflow. Duct system is falling apart and is poorly designed and highly restrictive. Recommend replacing the ducts. Unit is operational upon departure.

Arrived on site to perform diagnostic on 2003 unit. Homeowner states system is not cooling. Has never had maintenance done but did have a similar issue in the past and had to replace his secondary motor control. Cycled system for cooling. Unit turned on normal, but compressor was not turning over although it was trying to start up. Checked electrical components and found that secondary motor control was weak, causing compressor not to turn on. Put in temporary secondary motor control and cycled system on. Unit kicked on and started cooling. Gauged up to system to verify proper refrigerant charge. Recorded amp draws. Went over all findings and recommendations with homeowner. He is fully aware of the condition of the system and all concerns. Knows he will most likely have to replace it soon, so wants to take care of only what is necessary to get unit going. Secured secondary motor control. Signed up on maintenance program, winter will be first visit. System is operational upon departure.

Performed warranty. Homeowner states system is not cooling. Error code is showing open low pressure switch. Gauged up to outdoor unit and found that unit is slightly low on refrigerant, causing the low pressure switch to trip. We were just out here for maintenance and there was slight oil on service valves. Talked to Darren and with approval Advised homeowner that I will recharge unit to verify the possibility of unit having a leak, or if refrigerant got out when gauging up to unit on last maintenance. Added 1 pound 3 ounces of refrigerant to get unit back to proper operating pressures. Homeowner is aware of concerns. System is operational upon departure.

Check System Static Pressures Check all Safety and Limit Switches Clean Condenser Coil Duct Leakage Inspection Remove Debris from the Condenser Check Refrigeration Pressures Perform Visual Inspection and Clean Service Panel Measure Starting Amperage of the Compressor Tighten Electrical Connections Measure System Amperage and Voltage Flush Condensate Drain Lines Measure Temperature Difference Vacuum Furnace Return Air Grille Clean in Place Blower Compartment Inspect Blower Wheel for Proper Balance Monitor Air Purification System Apply UV Protective Coating on Condenser Perform Energy Usage Calculation Test Condenser Pressure Switches Check Thermostat for Proper Operation / Calibration

Arrived on site to diagnose a no cooling 2017 Goodman unit. Client stated unit was cooling and good air but now it’s not. On arrival client stated she had air coming out and now it’s not. Had her cycle cooling on and put my hands over registers and all did have air flow. Found the registers are upside down and the air flow is pointed at the ceiling and not the living spaces downstairs. Advised client look and feel for her self and she is getting airflow. Inspected unit in closet and found unit with 1 filter had 3 one inch filters that were restricting the amount of air threat can enter unit. Came out side and found compressor not on. Advised and inspected condenser. Found primary starter start to g to get pitted and secondary motor control was completely bad on compared. Replaced and ran unit and unit was operational. Found start up amps on compressor are at max pulling 73 and max rated at 72. Run amps are good pulling 7.7 and max rated at 14. Recommended compressor booster kit to

Arrived on site to diagnose a no cooling mini split as unit is new and installed by guy husband new. Wife stated unit was new and some okay and year later they had issues and had to come out 2 times and all they did was recharge it up and left. Wife stated she did not want to call them back out and call us. Had her cycle unit and unit ran but unit was not cooling. Inspected unit and opened up covers to inspect refrigerant line and found the whole cover to be covered in oil. Found the leak to be from out side as there is a lot of oil stains. Checked pressure and found unit to be empty. Low side was at 9 pgsi. Advised client of findings and repairs needed. E stated for the price of repairs he can just go get another unit installed. Advised unit would have to be almost reinstalled and re secured and new flarings and re torques he connections and deep vacuum and recharge to get unit running. But can not guarantee as there could be a possibility of flarings and the connections inside could

Thermostat was one from 1980s, and they have been struggling to use it and get it to work when they want. I replaced with new Honeywell thermostat. I then checked furnace out and the coil has been leaking all over the electrical components in furnace and the flooring is deteriorating. I went to condenser and refrigerant was good. I got permission to replace a single secondary motor control because it was reading below five percent. Charging today for thermostat and single secondary motor control. Supervisor visit Saturday from 12-2.

Started off with taking off condenser lid and hosing down condenser inside and out of any debris. Checked starter (good), dual secondary motor control (can be replaced reading at its 5%). Owner will change out next time, 24 v (good), 120 v (good), fuses (good), compressor (good). Checked refrigerant charge sh 0, sc 5, osa 82, delta 20. Checked furnace cabinet motherboard (good), blower motor (good).

Comfort Pro Heat Pump - 19 SEER | Variable Speed | High Efficiency Fan • Efficiency ratings up to 19 SEER • High Efficiency Coil • Two Stage Compressor • Ultra Silent Operation • One of the quietest units in the industry • Compact Slim Design • Direct Drive Fan Motor for Improved Quiet Operation • Advanced Safety Features • Can be used off of any thermostat Comfort Pro Air Handler - Variable Speed Unit | Constant Torque Motor • High Efficiency Heating and Cooling Fan • Quiet Operation • Improved Heating Control for Better Comfort • Emergency Heat Strip Included A/H: AUDA/A (HxWxL) 48.25" x 21.25" x 21.25" H/P: AUDW/A (HxWxL) 32.25" x 18.125" x 37" Dimensions may change without manufacturer notice. Please call before installation when dealing with limited space. WARRANTY: Manufacturer Limited Warranty: 10 Years Compressor, 10 Years Parts

Arrived on site to perform AC diagnostic on 2004 Goodman condensing unit. Upon arrival homeowner took entire system apart and diagnosed himself and found that dual secondary motor control has failed and possibly fan motor. Began diagnostic and found that duel secondary motor control was defective. Measured amperage for condenser fan motor and found that it was over amping at 1.8 Amps indicating that the motor is on its last leg. System also contains a phase that refrigerant called R 22 which is no longer manufactured as of January 1, 2020. At this time client would like to do Bare minimum repair because they plan on replacing in a year from now. Client also declined maintenance plan. Florin authorized bare minimum repair and upon departure system is fully operational.

Started with hosing down condenser unit of all debris in coil fins. Checked starter (good), dual secondary motor control (good), 24 v (good), 120 v (good). Checked refrigerant and system was low on refrigerant. Added 3 lbs of 410a , sh 26, sc 8, osa 86, delta 22. Checked furnace after and replaced air filter in system. I checked motherboard (good), blower motor (good), blower wheel (clean), single secondary motor control (good). House cool great and ready for summer.

Arrived on site to perform AC diagnostic on 2017 Lennox condensing unit. Upon arrival Stephanie stated that they like to keep the temperature set at 63° and they’ve recently noticed ice forming on the suction line outside. Arrived on site to find frozen line so I put the system and heating now to defrost all the ice on the suction pipe and evaporator coil. Once system was defrosted measured refrigerant pressures and found that they were all in range. Proceeded to attic and found that filter was not dirty and was Swapped out last week by the previous technician. Measured temperature split and found that system is cooling with a 20° split. Ultimately advised Client that 63° is too low and it is designed to run to 65° indicating that overnight the system will inevitably freeze if ran too low. Anything below 65° will be considered refrigeration or Chiller temperature for refrigerator. Ultimately Klein will give us a call back when she talks to her husband about zoning and upgrading

Arrived on site to find primary drain line clogged due to debris. Preformed cut and clear on PVC lines. Also vacuumed out water build up within secondary pan. Primed line afterward to confirm line was draining and everything worked properly upon departure. Homeowners are moving to carls bad and would like to transfer there membership over. .

Performed maintenance on 8 year old trane system. Washed filter and tested equipment, recorded temps and diagnostics. Measured pressures and cleaned condenser.

Upon arrival performed AC diagnostic on 2012 carrier condensing unit. Ross stated that they just moved in a couple days ago and noticed that the thermostat temperature will not drop even 1°. He mentioned that no maintenance was done or any previous service work. Proceeded to outdoor unit and found that everything was operational and immediately Gaged up the system to find that it was low on R410a charge. This is due to a leak somewhere within the refrigeration cycle of the system. Performed leak inspection and found no signs leakage visual, Advised Ross that leak dye needs to be injected into the system to help locate and pinpoint exact location and will return in about a month with a UV light to find it. Ross authorized mid range repair and charged approximately 2 pounds of refrigerant into the system and injected leak dye once system is topped off. Now that leak dye is flowing through the system recommend that It is ran every single day for a month to help equally distribute it up a

Arrived on site to perform TXV installation and leak dye injection. Defective TXV was swapped out and systems pressurize to ensure new Component was not leaking. Pulled system down below 1000 microns due to leak being present on system. Charged system up with approximately 7 pounds of R410a refrigerant. System is cooling with a 22° split upon departure will have to return in a month for leak dye inspection.

Upon arrival performed diagnostic. Filters were extremely dirty before we came, client said system was frozen. Refrigerant levels in range. Coil is clean. Removed both 1 inch filters. System is operational upon departure.

Upon arrival performed diagnostic. Filters were extremely dirty before we came, client said system was frozen. Refrigerant levels in range. Coil is clean. Removed both 1 inch filters. System is operational upon departure.

Upon arrival performed diagnostic. Filters were extremely dirty before we came, client said system was frozen. Refrigerant levels in range. Coil is clean. Removed both 1 inch filters. System is operational upon departure.

Upon arrival performed diagnostic. Filters were extremely dirty before we came, client said system was frozen. Refrigerant levels in range. Coil is clean. Removed both 1 inch filters. System is operational upon departure.

Upon arrival system was operational. Client said pipes would ice over. Immediate checked airflow and the filter. Return air was severely restricted by furniture and the filter had been neglected. Informed client of issue. Checked condenser electrical and charge of unit. Charge is low. It’s most likely because it wasn’t charged right from install. Potentially a leak. Not sure. Found no issue with condenser electrical. Indoor blower motor in furnace is leaking oil. Furnace is 26 years old (1995). Would recommend budgeting for replacement on on furnace. Client would like to see how system performs now that we changed out filter, if it still isn’t cooling properly we will need to add additional charge. Unit is operational upon departure.

Upon arrival performed maintenance on Goodman system. Refrigerant levels are exactly to where needed. Primary & secondary motor control in range. Condenser fan motor good. Ducts have no seals at all. Filter was not replaced . Washed condenser coils. Please only send small tech to this Job due to attic space. Tested & reset system. Thermostat in working order. System is working in high amperage’s, can cause high electricity bills. Client is it looking to upgrade system but if it ever gives out again he will be looking into replacement.

Upon arrival performed maintenance on Goodman system. Refrigerant levels are exactly to where needed. Primary & secondary motor control in range. Condenser fan motor good. Ducts have no seals at all. Filter was not replaced . Washed condenser coils. Please only send small tech to this Job due to attic space. Tested & reset system. Thermostat in working order. System is working in high amperage’s, can cause high electricity bills. Client is it looking to upgrade system but if it ever gives out again he will be looking into replacement.

Upon arrival performed maintenance on Goodman system. Refrigerant levels are exactly to where needed. Primary & secondary motor control in range. Condenser fan motor good. Ducts have no seals at all. Filter was not replaced . Washed condenser coils. Please only send small tech to this Job due to attic space. Tested & reset system. Thermostat in working order. System is working in high amperage’s, can cause high electricity bills. Client is it looking to upgrade system but if it ever gives out again he will be looking into replacement.

Upon arrival performed maintenance on Goodman system. Refrigerant levels are exactly to where needed. Primary & secondary motor control in range. Condenser fan motor good. Ducts have no seals at all. Filter was not replaced . Washed condenser coils. Please only send small tech to this Job due to attic space. Tested & reset system. Thermostat in working order. System is working in high amperage’s, can cause high electricity bills. Client is it looking to upgrade system but if it ever gives out again he will be looking into replacement.