Vista, CA

Arrived on site to perform furnace maintenance on 2014 AC pro heater. Upon arrival client stated that he just moved in recently for one year and wants to get the yearly maintenance done. Maintenance checked out properly. Filter was swapped by client. Temperature rise is in range. Amps for indoor blower and inducer are in range. Indoor blower showed no signs of oil leakage and single secondary motor control in range. Circuitboard had slight burn mark but was in good condition at this time recommended surge protection on unit To increase longevity. System is pre-plumbed for AC refrigeration. Flame sensor was cleaned and hot surface igniter is in range. Gas valve is opening and closing and shows no signs of gas leakage. Discussed full maintenance with client and he is aware of current condition. At this time he would like to hold off on the maintenance plan because he prefers One time visit. Advised that maintenance plan would be cheaper due to the AC not being present at the house. Upon

Upon arrival performed maintenance on package unit . Replaced air filter. Also did better cleaning on indoor coil, they had it packed with dirt & debree. Amperage’s & refrigeration are in range. Primary and secondary control in range. Washed outdoor coils. System is operational. Thermostat operational. System is running and washed. Filters swapped.

Upon arrival performed maintenance on package unit . Replaced air filter. Also did better cleaning on indoor coil, they had it packed with dirt & debree. Amperage’s & refrigeration are in range. Primary and secondary control in range. Washed outdoor coils. System is operational. Thermostat operational. System is running and washed. Filters swapped.

Upon arrival performed maintenance on package unit . Replaced air filter. Also did better cleaning on indoor coil, they had it packed with dirt & debree. Amperage’s & refrigeration are in range. Primary and secondary control in range. Washed outdoor coils. System is operational. Thermostat operational. System is running and washed. Filters swapped.

Upon arrival performed maintenance on package unit . Replaced air filter. Also did better cleaning on indoor coil, they had it packed with dirt & debree. Amperage’s & refrigeration are in range. Primary and secondary control in range. Washed outdoor coils. System is operational. Thermostat operational. System is running and washed. Filters swapped.

Performed AC tuneup on 6 year old Payne condenser and 1 year old FAU. Performed static pressure test and found system to be high, mainly on the return side. This can be remedied with cutting a new return into the system. Temp split is normal. Cleaned condensate P trap and flushed line with water. Inspected electrical connections. Replaced filter with owner-supplied filter. Inspected and cleaned in place blower compartment. Blower sounds balanced. Performed deep cleaning on condenser coil fins and exterior unit. Inspected electrical components and found condenser fan motor to be pulling 1.3 amps, FLA is 1.4. I brought this to Kathleen’s attention and she would like to forego replacing the motor at this time. The starter looks good and the dual secondary motor control is within limits. Refrigerant temperatures and pressures look normal. Upon departure system is operational.

Arrived on site to perform diagnostic on system. AC System is from 1988, furnace was replaced in 2018 prior to Tony moving in to home. Homeowner states that system is not cooling. Stopped cooling last night and he shut it off since. Cycled system for cooling. Indoor unit turns on normally, outdoor condenser unit sounds like it wants to turn on, but doesn’t. Opened up electrical compartment and immediately smelled burning from inside. Primary motor control has burnt up, as well as high voltage wiring going to compressor and secondary motor control. Went over immediate findings with homeowner. He also mentioned that system has had history of blowing a fuse or two a couple times in the last years. Went over immediate repairs, did advise that this is only the repairs needed to try to get the system Up and going, can not guarantee that it is the only repairs that will be needed. After discussing everything thoroughly, homeowner would like to go over replacement options. Turned call over

Removed contaminated refrigerant from system. Pulled deep vacuum and the system remained under 1000 microns. Recharged system with new R-410A refrigerant. Subcool was maintaining 15 degrees, temperature split is 20 degrees. Removed blower housing and cleaned blower compartment. Removed original blower motor and cleaned blower assembly. Installed new blower motor and secondary motor control. Reinstalled blower assembly in furnace and ran it to ensure that it is balanced. Opened coil box and cleaned coil with foaming no-rinse evaporator coil cleaner. Placed gel tab in drain pan to help keep the condensate drain line clean. Closed coil box and resealed with foil tape. Upon departure system is operational.

Arrived on site to perform AC tuneup on a 2017 carrier unit. Upon arrival David stated that the system has been working fine but he has never had a maintenance and recently noticed that it has becoming really loud. Began maintenance an outdoor unit and performed deep cleaning on condenser coil. Inspected the condenser fan motor and found no oil leakage but slight oxidization. Duel secondary motor control is weak on hermetic side terminal And will lead to possible failure in the future. Starter showed no signs of Pitting or burn marks. Condenser is significantly close to the wall which is resulting in a higher subcool on the refrigerant pressures due to this airflow restriction. Refrigerant pressures still looked OK. Amperage is fairly high on compressor and fan motor is in range. Discussed full maintenance with David and he is aware of possible failure points within the system. At this time he would like to hold off on signing up on the maintenance plan and will give us a call if anyth

Arrived on site to perform condensation diagnostic on five-year-old unit. Upon arrival Mr. Santos stated that just about a couple weeks ago they noticed that the secondary drain was leaking. Began diagnostic at attic and found that primary drain was backed up and flooding in secondary pan. Inspected primary pan cannot see any visible cracks at this time. Perform cut and clear and nitrogen blowout on condensation lines, system began a drain properly. Client signed up on maintenance plan to keep units at standard. Upon departure system is operational and draining

Upon arrival started ac tune ups. Cleaned out condensers. Charge on both systems are good. Compressor amps are within range. Both start capacitors are failing and should be replaced. Both fan motors are also rusted out and failing. Advised clients on condition of units. Hooked up Wi-Fi thermostat to clients phone. Both units are operational upon departure.

Upon arrival found system operational. Found system inside to be very dirty. The office is setting up an appointment for install to come back and install merv rack for system for better filtration. Blower wheel cleaning will be given to client, and full maintenance to be done at that time. Advised client that we will be in touch when new coil comes in and we can come out and take care of filtration issues. Not running system till new filter gets here. Did not perform tune up

Upon arrival found system operational. Found system inside to be very dirty. The office is setting up an appointment for install to come back and install merv rack for system for better filtration. Blower wheel cleaning will be given to client, and full maintenance to be done at that time. Advised client that we will be in touch when new coil comes in and we can come out and take care of filtration issues. Not running system till new filter gets here. Did not perform tune up

Upon arrival found system operational. Found system inside to be very dirty. The office is setting up an appointment for install to come back and install merv rack for system for better filtration. Blower wheel cleaning will be given to client, and full maintenance to be done at that time. Advised client that we will be in touch when new coil comes in and we can come out and take care of filtration issues. Not running system till new filter gets here. Did not perform tune up

Upon arrival found system operational. Found system inside to be very dirty. The office is setting up an appointment for install to come back and install merv rack for system for better filtration. Blower wheel cleaning will be given to client, and full maintenance to be done at that time. Advised client that we will be in touch when new coil comes in and we can come out and take care of filtration issues. Not running system till new filter gets here. Did not perform tune up

Upon arrival performed AC tuneup on 7 year old Bryant unit. Temperature split was normal. Flushed condensate drain line with half gallon of water. Noticed filter was allowing a lot of unfiltered air to pass through the furnace. Cleaned blower compartment and logic board. Found secondary motor control to be out of limits on the low end. Inspected blower wheel and found it to be very dirty. I brought this to Pamela’s attention. She would like to go through with the blower wheel cleaning and evaporator coil cleaning. Found liquified grease on outside of blower motor. They would like the motor and the secondary motor control to be replaced as well. Replaced the filter with owner-supplied filter. Performed deep cleaning on condenser coil fins and exterior unit. Removed debris from bottom of condenser. Checked electrical components and all are within limits. While checking the refrigerant temperatures and pressures I noticed the subcool to be jumping around between 12 and 20

Arrived on site to perform AC diagnostic on two system carrier 2005 units. Upon arrival Barry stated that they only use the system maybe two weeks out of the entire year and just recently noticed that both of them were no longer blowing cold air. They have lived in the house for 12 years and have never maintenance the unit. Begin diagnostic at left wing unit And immediately found that duel secondary motor control was defective. Once unit fired up with new component, I found that refrigerant pressures were low. This is due to a possible leak within the refrigeration cycle of the system. Condenser fan motor has significant oxidization. Proceeded to right wing bedroom unit and found that duel secondary motor control was also defective. Installed new component in system fired up as well. Signs of nest around unit showed that sticks were stuck in condenser fan motor preventing It from spinning. Systems are 17 years old and past design life ultimately any repairs done are considered a Band-

Upon arrival unit was operational and cooling. Started at the indoor unit checked amps they were in range, temp split was in range. Condensation line was clear of debris and blower wheel spun freely and was free of oil. Filter was slightly dirty but still good. Moved to the out door unit checked system amps and washed the unit. Upon departure unit was operational and cooling.

When I arrived at condenser unit, the condenser fan motor wouldn’t spin. I opened cabinet up and started checking all windings to motor. I found that the fan motor is seizing up every time you give a call for cool. The condenser fan motor and module need to be replaced. Calling distribution to get pricing for both and then we’ll figure out a date to come back out and install. Installed new motor and module. System took off immediately after, system is operating properly. Charging for motor today.

Client was concerned about chips of white paint coming from vents -I reassured him that it is paint chips that are coming loose from the metal boots

Client stated no cooling -Technician found refrigerant levels to be about 2 lbs low -A refrigerant leak is apparent -Fan motor was also drawing way too much power -Clients felt repairs did not make much sense, considering age and price of repairs -System replacement was discussed, they are not looking to do so at the moment

It was raining. Waited on site 40 mins. Did not stop raining. Rescheduled. Client understood completely.

Client stated no cooling -Condenser is operational -Refrigerant levels are within range -Electrical components are working properly -Condenser coil was very plugged up and dirty, I cleaned it out thoroughly for maximum airflow -Filter was recently changed out -Air is about 57 degrees which is right where you want it to be -System is cooling properly

Client stated no cooling -Starter was changed out last time due to a shorted internal coil -There is another starter in the system that powers the internal motor -When that starter would be energized with 24v, the fuse would trip -That start was replaced -The system is functioning properly now -Currently cooling