Menifee, CA

Performed Furnace diagnostic on 2006 aireflo downstairs heater. Upon my diagnostic customer stated that a previous company had been out twice already and replaced the flame sensor. Turned thermostat on upon diagnostic and heard nothing start up inside the attic. Proceeded to downstairs unit Furnace and found that system has power but was in lock out. Error code 22 Was active due to a flame sensor not being able to detect the flames coming off of the burner. Clean flame sensor and readjusted Into a better position and system was able to detect a flame at the circuitboard. Although circuitboard had multiple heat spots which is an indication that the board may be going bad and can experience intermittent behavior also could’ve been contributing to the flame sensor not being detectable. Also did an inspection of the upstairs unit and found that he blower motor was pulling at 6 A along with a static pressure of 0.90 which is tremendously high, this is an indication of a restriction. Downs

Performed furnace maintenance on 2012 Coleman mobile home heater. 1. Furnace cabinet completely covered in dust and debris you to 1 inch filter is not being swapped out enough they said resulted in the walls being covered 2. Indoor blower motor is also layered in a blanket of dust which will ultimately cause Interference with the motors performance 3. Single secondary motor control is reading at 5.0 which is incredibly weak for its actual reading which is supposed to be at 7.5 this is due to the fan motor being overworked 4. Indoor blower motor is in need of an intense deep cleaning due to the dust that is collected on the scroll wheel and motor 5. Scroll wheel can be thrown off balance due to unnecessary weight of dust and debris 6. Duck work on their home is completely disconnected and uninsulated On certain parts of the home Discussed that system is bad condition and homeowner Patricia is total aware. Mentioned that friends from church that will be coming to redo all of the ductwor

Arrived on site to perform heating tune up on 2 package units. One original to home and other 2007. Filters were dirty recommended replacing every 3 months. Blower assembly on both units have dirt accumulating on wheels creating high stress and causing motors to work harder. Recommend cleaning blower assembly’s on both units. Main unit blower is okay no oil. Added on unit is starting to leak oil as there is layer of oil and dirt accumulating From past years. Recommend replacing 1 blower motor to extend life of units and to run easier. Found both inducer motors have been working really hard as they both have inducer motors covered in oil from over working in its past years. Amp drawls are high on both inducer motors just indicating self wear and could fail in future due to condition and working hard. Recommend replacing both inducer motors before they completely fail and heaters will not operate properly. Drain lines are good and running of of ceiling. Inspected both heat exchanger p

Tested both furnaces for operation and performed annual service maintenance. Replaced filters. Tested thermostats. Measured internal temperature rise. Recorded voltages and blower amp draws. Recorded inducer amp draws. Measured capacitors. Tested ignitors. Cleaned flame sensors. Inspected ducting. Inspected gas piping.

Arrived on site to perform diagnostic. Furnace is not heating. Cycled system for heating. Verified proper heating sequence. System shuts off before blower kicks on. Performed diagnosis. Found partially restricted vent pipe. Went up to roof to re-arrange vent pipe. Also found main pressure switch is bad again. Need to order and return to change pressure switch. Ordered part from Lennox In riverside, will be shipping to us ASAP.

Performed furnace maintenance on 2005 trane heater. Upon my maintenance I noticed a few things that were addressed with the homeowner. 1. Flame Since was in very bad condition and oxidized. This can lead to failure on start up for heating 2. Static pressure was 0.70 indicating to me that there is a high Airflow restriction 3. Indoor blower cabinet was covered in dust and debris due to Horse hair filter inefficiently stopping dust particles. 4. Hot service igniter was reading in 168 ohmes which is incredibly high. This is due to the hotspot that is formed on it from the past years of usage

Inspected the furnace for noises and tested gas pressure, measured temp rise.

Performed Furnace maintenance five-year-old Goodman heater.

Upon arrival performed maintenance on furnace system. Indoor motor is in good condition. Circuit board and electrical connections good. Blower wheel dirty and recommend cleanings. Upgrading filtration recommends to keep system clean and better filtration. Inducer draft motor in good conditon. Safety switches in good condition. Evap coil clean. Burners in good condition. Temp rise good. Purged through condensate lines. Gas shut up and gas flexing with gas pipe is in good condtion. Ducting is not properly sealed and has junction boxes that are not sealed. Cleaned outdoor of furnace cabinet and blower cabinet. Amperages throughout system good. 1. Dirty blower wheel 2. Poor filtration 3. Surge protection recommended to keep electrical protected 4. Upgraded filtration recommended 5. System operational upon departure.

Upon arrival performed maintenance on furnace system. Indoor motor is in good condition. Circuit board and electrical connections good. Blower wheel dirty and recommend cleanings. Upgrading filtration recommends to keep system clean and better filtration. Inducer draft motor in good conditon. Safety switches in good condition. Evap coil clean. Burners in good condition. Temp rise good. Purged through condensate lines. Gas shut up and gas flexing with gas pipe is in good condtion. Ducting is not properly sealed and has junction boxes that are not sealed. Cleaned outdoor of furnace cabinet and blower cabinet. Amperages throughout system good. 1. Dirty blower wheel 2. Poor filtration 3. Surge protection recommended to keep electrical protected 4. Upgraded filtration recommended 5. System operational upon departure.

Upon arrival performed maintenance on furnace system. Indoor motor is in good condition. Circuit board and electrical connections good. Blower wheel dirty and recommend cleanings. Upgrading filtration recommends to keep system clean and better filtration. Inducer draft motor in good conditon. Safety switches in good condition. Evap coil clean. Burners in good condition. Temp rise good. Purged through condensate lines. Gas shut up and gas flexing with gas pipe is in good condtion. Ducting is not properly sealed and has junction boxes that are not sealed. Cleaned outdoor of furnace cabinet and blower cabinet. Amperages throughout system good. 1. Dirty blower wheel 2. Poor filtration 3. Surge protection recommended to keep electrical protected 4. Upgraded filtration recommended 5. System operational upon departure.

Upon arrival performed maintenance on furnace system. Indoor motor is in good condition. Circuit board and electrical connections good. Blower wheel dirty and recommend cleanings. Upgrading filtration recommends to keep system clean and better filtration. Inducer draft motor in good conditon. Safety switches in good condition. Evap coil clean. Burners in good condition. Temp rise good. Purged through condensate lines. Gas shut up and gas flexing with gas pipe is in good condtion. Ducting is not properly sealed and has junction boxes that are not sealed. Cleaned outdoor of furnace cabinet and blower cabinet. Amperages throughout system good. 1. Dirty blower wheel 2. Poor filtration 3. Surge protection recommended to keep electrical protected 4. Upgraded filtration recommended 5. System operational upon departure.

Adapt new cooling system to existing furnace. Install 2 stage relay kit on existing furnace to operate 2 stage blower on existing standard PSC furnace. Re-seal and re-insulate exposed ducting with r-6. All items are listed in full description below. Attic ducting to be re-sealed and strapped for optimal performance. Options to remove from quote: No Permits/HERS $-750 No High Flow registers with seal $-300 No Supply Plenum $-100 No Wifi T-Stat $-275 Finance Options= 0-Down 24 months 0% or 90 days 0% interest 0 payment defaults to 6.9% after 90 days with no pre-payment penalty ($98 per month)

Arrived on site to perform diagnostic on 14 year old unit. Homeowner states that upstairs system is not cooling, and it has not been cooling since the summer time. He has been going back and forth with his home insurance on getting them to fix it. Homeowners neighbor does HVAC, and he informed me that system has a refrigerant leak. He added 7 pounds of r-22 refrigerant and has already leaked it out. Neighbor had advised him to have a company perform a isolation test, so he would like a price from us to perform an isolation test to send over to his home insurance. Checked and Verified that refrigerant levels are in fact low and that is why unit is not cooling. System is flat on refrigerant. Isolation test would be the best option to find leak on unit. Also talked to homeowner about system replacement as we were out here in the past to quote for system replacement. Emailing quote to homeowner, system is not operational upon departure.

Arrived on site to do repairs on a 2008 Goodman system. Arrived back on site to install a new plenum, Merv cabinet, New filter, door switch, surge protector, and blower assembly cleaning. Client is aware of all repairs done. Cycled system after install to ensure system operating. Cycled system in heating and cooling to ensure system operating. Client is aware of how system is running and all repairs done today. Client approved all repairs and is happy with all work done. System is operational upon departure.

Arrived on site to perform fall tune up on a 2008 Goodman system. Furnace and evaporator coil located in attic client stated no issues. Cycled heating mode on and system was operational. Advised the summary of findings are as followed. Furnace 1. 2008 Goodman furnace located in attic. 2. Found filter dirty and replaced filters. Recommended upgrading filtration to a merv cabinet to reduce amount of dirt entering system. 3. Found system to not have a door switch. Which can be a safety Risk for anyone who works on system. Recommend adding a door switch for switches and be safe to service any time we are out. 3. Blower assembly really dirty and cleaned and wiped down dirt upon blower compartment. 4. Blower assembly is dirty. Wheel dose have dirt build up from dirt entering system. Recommend a blower assembly cleaning to help reduce stress and wear on motor to run more efficiently and stress free. 5. Blower motor is good and free of oil. Amp drawls are in range. 6. Inducer motor is go

Performed furnace maintenance on 2000 carrier System. On my maintenance there are multiple points or concerns that were addressed with Ms. Brown. 1. Indoor blower motor is leaking oil from bearing, dirt and debris has began to collect on the top of the motor this can cause overheating. 2. Found that capacitor has become out of range, This has occurred due to the fan motor using more power than needed 3. Static pressure on system was 1.7. This is way too high and is an indication of air restriction. system is designed for .50 and your system is exceeding that tremendously. 4. Found that secondary drain line has cracked in rotted due to age.this can cause a major flood over or leakage onto the ceiling or other components around it there. there is already previous water stains from the past due to leakage. 5. Slab Evaporator coil Is clogged with Dirt, hair, and skin particles from past years. Need cleaning 6. Entire system from evaporator coil to indoor blower cabinet needs an intensive

Measured system starting load and installed compressor assist kit. Inspected system for odors.

Arrived on site to perform fall tune up on a 2003 carrier system. Furnace and evaporator located in attic client stated no issues. Cycled heating on and system operating. Thermostat is good. Advised the summary of findings are as followed. Furnace 1. 2003 carriers. 2. Filter was dirty and recommended replacing. 3. Found black flex ducting used. Found system restricted of air flow as there is not enough air flow going into system. Would need to add more return 4. Blower assembly and wheel has dirt build up creating stress on motor. 5. Motor is good at this time. Amp drawls are pulling 10.7 and max rated amp is 13.7 indicating motor is showing signs of wear and could fail in future due to it’s condition. 6. Seconds motor control is good and in range. 7. Inducer motor is good and amp drawls are in range. 8. Inspected heat exchanger compartment it self. Found heat exchanger to have a crack from over heating as it dose have heat impingement and hot spots from over heating. Filled wit

Ordering part for Mr, Smith from silgler.

Ordering part for Mr, Smith from silgler.

Ordering part for Mr, Smith from silgler.

Ordering part for Mr, Smith from silgler.

Upon arrival system was not turning on for heat. Cycled system for heat , would not kick on, gas pressure was at .2 when calling. Adjusted outlets gas pressure to 3.5 system is operational, signed client up for esa.

Upon arrival system was not turning on for heat. Cycled system for heat , would not kick on, gas pressure was at .2 when calling. Adjusted outlets gas pressure to 3.5 system is operational, signed client up for esa.