Menifee, CA

Upon arrival performed heating maintenance. Have been here previously, have done repairs and cleanings. Advised client, to replaced filter every 1-2 months due to where house is located. Advised if we do not replace filter we will start going back to what happened before, parts and motors failing due to dirty systems. Dirty filters. Replaced filter, dusted off electrical connections. Secondary motor control is out of range and needs replacement. Client left to work, wanted email. Will follow up with client. System is operational. Client doesn’t use heat a lot due to high propane costs. Advised moving to all electric heating and cooling can possibly be an option.

Upon arrival performed heating maintenance. Have been here previously, have done repairs and cleanings. Advised client, to replaced filter every 1-2 months due to where house is located. Advised if we do not replace filter we will start going back to what happened before, parts and motors failing due to dirty systems. Dirty filters. Replaced filter, dusted off electrical connections. Secondary motor control is out of range and needs replacement. Client left to work, wanted email. Will follow up with client. System is operational. Client doesn’t use heat a lot due to high propane costs. Advised moving to all electric heating and cooling can possibly be an option.

Performed heater maintenance on a 2020 lennox gas furnace. Customer reports light useage of the heater this season. Systems heating temperature split is in range . Sensors and switches were cleaned and tested. Gas valve and ignitor were measured and tested. Filter is dirty. Duct runs are sealed. Condensate lines are clear. System is not protected. Homeowner was briefed on the system. Unit is operational at end of appointment.

Preformed furnace maintenance on 2020 carrier heater

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance in the attic by performing a duct leakage inspection. I then proceeded to the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filters have been checked, do not need to be changed at this time. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection I found the blower housing and scroll wheel to be heavily impacted with dirt and dust, recommend a blower housing pull and clean be performed to alleviate premature wear on the blower motor. Upon departure system is working and operational.

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance at the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been changed, cool air provided. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of the indoor unit, I found the the blower housing and scroll wheel to be heavily caked with dirt and dust, as well as the secondary motor control to be below rated values. Recommend a blower housing pull and clean be performed to alleviate premature wear on blower motor. Replaced secondary motor control at this time. Upon departure sy

Performed diagnostic on a 2016 Day and Night gas furnace. Homeowner reports unit not turning on. Found power at the thermostat but unresponsive when calling for heat. A high limit switch is going off at a really low temperature causing the system to go into lockout. Part is ordered from sigler. Returning to install part once part is in house.

Clean and Adjust Burners Check Combustion Air for Proper Venting Examine the Heat Exchanger for Damage / Corrosion Test Furnace Safety Controls Inspect Gas Piping Tighten Electrical Connections Measure the Voltage and Amperage Flush the Condensate Drains Measure Tempurature Difference between Supply and Return Air Vacuum Furnace Return Grille Adjust Gas Pressure & Pilot Clean in-place Blower Compartment Inspect Blower Wheel for Proper Balance Check the System's Static Pressures to Ensure Proper Airflow Inspect Duct Connections for Air Leaks / Sizing / Insulation Monitor Air Purification System Check all System Safety and Limit Switches Clean Flame Sensor Inspect Carbon Monoxide Detectors Check Thermostat for Proper Operation / Calibration

Performed combo maintenance with install. Heating controls were measured and we in range. Sensors and switches were cleaned and tested. Gas valve and ignitor are operational. Duct runs and condensate lines are clear. System is equipped with a UV light, this is ok at this time. Filter is dirty. Outdoor unit was very dirty and chemically washed today. Refrigerant levels were verified in range. Electrical component amp draws are good. Indoor and outdoor unit are not electrically protected.

Performed maintenance on a 2021 gas furnace in menifee. Customer reports frequent use of heat this season. System kicked on with no issues. Filter is clean. Sensors and switches were cleaned and tested. Duct runs are sealed. Condensate lines are clear. Furnace motors are reading in range. Gas valve and ignitor were measured and tested. Condition was discussed with customer. System is operational.

Upon arrival, found 1 Lennox system. Duel fuel set up. SL280. Inspected heating components. Found no issues with the motors or other parts. Heat rise is good. Some ducting is older and should be replaced at one point. All safety components are working good. No issues found with heater. Cleaned outside of system and replaced filter with customer supplied filter. Unit is operational upon departure.

Performed fall maintenance on a 1999 gas furnace in a manufacture home. System is heating 17 degrees. Inducer motor is amping over manufacture specs. Primary blower is amping high and leaking oil. Blower wheel is dirty. Gas valve and ignitor are causing the system to heat very low and ignition takes over a minute. The homeowner is aware of the extensive repairs needing to get this furnace to be reliable. Parts are ordered and System is operational at end of visit.

No leak detected, system is going off on high pressure. Txv is clogged. Need to return with mike or Dave to complete this repair. Tim paid for level 9 repair today.

Arrived on site to perform fall tune up on 2 2004 comfortmaker units. Both located in attic. Client stated no issues just know u its are old bit heating. Cycled both and good. Both filter are really dirty and need replacement. He said he would do it himself. Both blower motors are really dirty and motors have been leaking oil in past. Down stairs is leaking a lot of oil. BOth secondary controls are out of range and weak and can fail. Motors have oil and dirt build up from dirt entering system. Found both units air flow to have a high static pressure as filter are restricting airflow. Temperature rise was high on downstairs and upstairs was okay. Heat exchangers have heat impingement but no cracks. Advised could get worse over time. Drain lines are clear but dirty at this time. No over flow switches. Inducer motor on upstairs is almost at max and can fail. Downstairs was at 0.6 and both max rated at 1.5 amps. No protection on old units and recommended adding some to help protect syste

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance in the attic by performing a duct leakage inspection. I then proceeded to the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been checked, does not need to be changed at this time. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Need to follow up with install date for new air quality components. Upon departure system is working and operational.

Performed one year old furnace maintenance on Lennox

Performed heating maintenance on a 2013 Lennox gas furnace. Customer reports frequent use of the heater. Filter is dirty and replaced today with a customer provided MERV 11. Return cabinet is very dirty, this was vacuumed today. Sensors and switches were tested and cleaned. Gas valve and ignitor were tested and recorded. Blower wheel is very dirty, this needs to be cleaned in the near future in order to prevent damage to the primary blower motor. Battery cap is leaking oil but still in range at this time. System condition was discussed with the homeowner. System is operational.

Upon arrival performed maintenance on heating system. Indoor motor is leaking oil. Bearing has given out and is releasing oil. Blower wheel is dirty and needs cleanings. Inducer motor is running higher then max amps. This is signed of failure. Circuit board and electrical connections good. Tried inspecting heat exchanger but cabinet is to small. Advised client I can check heat exchanger. Client declined to pull exchanger, does not wanna fix this system. Client is getting solar. Advised to move over to dual fuel to UTILIZE entire solar. And use gas as emergency heat. Client said he will call office when ready.

Upon arrival performed maintenance on heating system. Indoor motor is leaking oil. Bearing has given out and is releasing oil. Blower wheel is dirty and needs cleanings. Inducer motor is running higher then max amps. This is signed of failure. Circuit board and electrical connections good. Tried inspecting heat exchanger but cabinet is to small. Advised client I can check heat exchanger. Client declined to pull exchanger, does not wanna fix this system. Client is getting solar. Advised to move over to dual fuel to UTILIZE entire solar. And use gas as emergency heat. Client said he will call office when ready.

Upon arrival performed maintenance on heating system. Indoor motor is leaking oil. Bearing has given out and is releasing oil. Blower wheel is dirty and needs cleanings. Inducer motor is running higher then max amps. This is signed of failure. Circuit board and electrical connections good. Tried inspecting heat exchanger but cabinet is to small. Advised client I can check heat exchanger. Client declined to pull exchanger, does not wanna fix this system. Client is getting solar. Advised to move over to dual fuel to UTILIZE entire solar. And use gas as emergency heat. Client said he will call office when ready.

Upon arrival performed maintenance on heating system. Indoor motor is leaking oil. Bearing has given out and is releasing oil. Blower wheel is dirty and needs cleanings. Inducer motor is running higher then max amps. This is signed of failure. Circuit board and electrical connections good. Tried inspecting heat exchanger but cabinet is to small. Advised client I can check heat exchanger. Client declined to pull exchanger, does not wanna fix this system. Client is getting solar. Advised to move over to dual fuel to UTILIZE entire solar. And use gas as emergency heat. Client said he will call office when ready.

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance at the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been changed at this time, home owner provided. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of the indoor unit I found there to be no form of electrical protection, recommend adding surge protection to protect the sensitive electrical components contained within the system. Upon departure system is working and operational.

Return for Filter Change- Changed merv 11 filter at unit, new filter is installed and system is working and operational upon departure.

Client has to think over membership, they are out of work and can’t do membership. Wanted to do the very basic tk get system up and going. Replaced igniter and got system gojng. Blower wheel is very dirty and needs cleanings. Inducer motor sounds really high pitched. Bearing might be going out.

Client has to think over membership, they are out of work and can’t do membership. Wanted to do the very basic tk get system up and going. Replaced igniter and got system gojng. Blower wheel is very dirty and needs cleanings. Inducer motor sounds really high pitched. Bearing might be going out.