Menifee, CA

Upon arrival performed combo tune up on Goodman system. Indoor motor and wheel are in good condition. Motor is running high in amps but it is a standard psc motor. Opened up entire condenser and cleaned out coil. Tested secondary motor control everything in range. Refrigerant levels in range. Circuit board & electrical connections in range. Installing surge protector for system. Installing whole home air purification system with merv 13 cabinet. System is operational upon completion.

Upon arrival performed combo tune up on Goodman system. Indoor motor and wheel are in good condition. Motor is running high in amps but it is a standard psc motor. Opened up entire condenser and cleaned out coil. Tested secondary motor control everything in range. Refrigerant levels in range. Circuit board & electrical connections in range. Installing surge protector for system. Installing whole home air purification system with merv 13 cabinet. System is operational upon completion.

Cooling Maintenance Performed- Upon arrival system is working and operational. I began my maintenance at the outdoor unit, I began by breaking it down and cleaning the coil with water and solution, removing heavy dirt and debris from the coil and housing. I then proceeded to check refrigerant pressures as well as record amp draws. I inspected electrical components for wear and tight connections. I then proceeded to the indoor unit. I checked static pressures as well as recorded temperature splits. I inspected the blower housing and checked electrical connections. Measured amp draws on blower. Flushed condensates and inspected components. Filter has been recently changed. Upon inspection of both units I found the starter on the condenser to be heavily pitted and show heavy arcing as well as the condenser fan motor to be leaking heavy oil and starting to seize, recommend having both of these parts replaced to ensure proper operation of the condenser, on the indoor unit I found the blower

Return to install OEM condenser fan motor. Motor was successfully installed and system is fully operational upon departure.

Installed Blower motor, ignitor, inducer motor and gas valve. Azure motor that was used did not need a battery cap so this was not charged. System was cycled.

System totals out to $15,716 - Client is only liable for payment of $9,716 as Tech Clean California Rebate will covering remaining $6,000 balance.

Replaced reversing valve. System is still pumping itself down. Will contact tech support for further actions. Customer is aware of the situation and still understanding.

Combo Tune Up Performed- Upon arrival system is working and operational. I began my maintenance at the outdoor unit by breaking it down and cleaning with water and solution. Removed heavy amounts of dirt and debris. I then inspected all electrical components for signs of wear and checked for tight connections. I measured amp draws and recorded refrigerant pressures. I then proceeded to the indoor furnace unit. Here I took temperature splits and measured static pressures. I inspected the condensate lines for proper drainage. I checked electrical components for tight connections and wear. Inspected the blower housing for balance and dust. Checked heating components for wear. Inspected heating components for proper operation. Filter has been checked and does not need to be changed at this time. Upon inspection of both units I found there to be no form of electrical protection, recommended and installed surge protection to both units protecting the sensitive electrical components contained

Performed maintenance on a 2020 Lennox AC. Systems cooling temperature split is good. Refrigerant levels are in range. Outdoor unit was chemically washed. Outdoor electrical amp draws are healthy. Insulation and wiring had damage from new puppy’s. This was quickly fixed today. Filter was changed. System is operational.

Upon arrival performed heating tune up on carrier system. Indoor motor and wheel are in good condition. System had a ton of dust. Went ahead and cleaned all furnace caging and dusted off all electrical components and inside of furnace. Circuit board & electrical connection. Filters were replaced. Client has 2 systems would only like the one we worked on last time when AC was giving him issues. Gas valve is in working order . Ducting is in very good condition. Strapped correctly , insulation levels are in very good condtion. Advised running surge protection to keep thermostats and all electrical connections protected in range ‘x

Upon arrival performed heating tune up on carrier system. Indoor motor and wheel are in good condition. System had a ton of dust. Went ahead and cleaned all furnace caging and dusted off all electrical components and inside of furnace. Circuit board & electrical connection. Filters were replaced. Client has 2 systems would only like the one we worked on last time when AC was giving him issues. Gas valve is in working order . Ducting is in very good condition. Strapped correctly , insulation levels are in very good condtion. Advised running surge protection to keep thermostats and all electrical connections protected in range ‘x

Upon arrival performed heating tune up on carrier system. Indoor motor and wheel are in good condition. System had a ton of dust. Went ahead and cleaned all furnace caging and dusted off all electrical components and inside of furnace. Circuit board & electrical connection. Filters were replaced. Client has 2 systems would only like the one we worked on last time when AC was giving him issues. Gas valve is in working order . Ducting is in very good condition. Strapped correctly , insulation levels are in very good condtion. Advised running surge protection to keep thermostats and all electrical connections protected in range ‘x

Upon arrival performed heating tune up on carrier system. Indoor motor and wheel are in good condition. System had a ton of dust. Went ahead and cleaned all furnace caging and dusted off all electrical components and inside of furnace. Circuit board & electrical connection. Filters were replaced. Client has 2 systems would only like the one we worked on last time when AC was giving him issues. Gas valve is in working order . Ducting is in very good condition. Strapped correctly , insulation levels are in very good condtion. Advised running surge protection to keep thermostats and all electrical connections protected in range ‘x

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance at the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been changed at this time. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of the indoor unit I found the blower and scroll wheel to be heavily impacted with dirt and dust, this is the components that moves all your air in your home no matter what mode the system is in, what this is doing is prematurely wearing out the blower motor, as well as I found there to be no condensate access or condensate safety, recommend

Performed maintenance on a 2020 Lennox high efficiency furnace. Brand new home and system in menifee. Customer reports normal operation of the system and frequent filter changes. System is cooling well with a 23 degree temperature split. Attic Water lines do not have an overflow switch this can lead to ceiling damage in case of a water line clog. Outdoor unit was very dirty and chemically cleaned today. Refrigerant levels were checked. Outdoor electrical components were measured and tested. Condition of system was discussed with homeowners wife. System is operational at end of appointment.

Returned to install a high limit safety switch. Customer reports normal operation after last diagnostic visit. During the visit adjustments of the registers were made which could have helped the over heating. During today’s check I found e the system heating at a high 61 degree split. This was adjusted to a more favorable temperature split that will help keep the systems components last. The sensor was switched out and system was cycled.

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance in the attic by performing a duct leakage inspection. I then proceeded to the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been changed, cool air provided. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of the indoor unit I found the scroll wheel and housing to be heavily caked with dirt and dust, as well as I found the inducer motor to be leaking oil and over amping, recommend a blower pull and clean be performed as well as the inducer motor be replaced to ensure

Arrived on site to diagnose leaking unit and mound noise when heating. Client unit heats up just sounds like water is in unit and a leak is present. Cycled unit and found loud noise from inducer as water is created using heater. Checked drain lines and was no draining. Cleared out inducer motor cap to drain water and cleared out with vacuum. Inducer motor has build up. Ram unit after was cleared put. Unit stopped making noise. Leak was still occurring. Found out that drain line has no ptrap or breather tube and it’s causing back pressure into inducer motor. Advised client and he saw and understood what was happening. Left blower cap off on Ac condensation line and inducer motor stopped leaking out. Ran unit for couple minutes and no more water leaking and unit was quiet. Advised filter was way over due and he stated he would replace on his own. Left unit with no filter as client wanted and he would put filter in so dose not Tripp code for low air flow. Cycled unit and is operational

Installed Outdoor TXV on a Trane heat pump. After install the system is still going off on high pressure. System has already had TXV replacements but next gen. We are returning to install indoor TXV. Cooling is working. Heat is not.

Arrived on site to preform furnace maintenance on 2012 Lennox heater. Upon arrival homeowner stated that system has been working fine and they’ve had no issues. Conducted safety inspection and full maintenance on system. I did come across a couple issues that were noticed. 1. Indoor blower motor is leaking a significant amount of oil which is causing it to pool at the bottom of the cabinet inside the furnace. If this condition worsens this will cause the motor to fail 2. Gas line did not have a sediment trap installed 3. System was not equipped with surge protection in the case of a power outage that may cause damages with electrical service Kelly was presented and informed about the condition of a 2012 system. Recommendations were shown to her and she would like to decline at this time. Will be emailing over recommendations. System was tested and is fully operational upon departure.

Performed furnace maintenance on 1993 comfort maker. Cleaned flame sensor. Inspected heat exchanger for safety. Evaporator coil is very dirty. Gas valve and ignitor were tested. Battery cap was out of range and replace today. Filter was clean and did not need to be changed. Homeowner was briefed of the condition. He reports selling the house in the near future. Unit is operational upon departure.

Return For IAQ Install- Upon arrival system is working and operational. Began install at the furnace, removed blower housing and motor, cleaned blower housing and scroll wheel as well as replaced motor with ecm motor. Then proceeded to clean the evaporator coil as well as install a phenomenal aire onto the coil. proceeded to replace the return plenum and re seal the duct system. Ensured system is operational and replaced thermostat, replaced thermostat to a sensi color touch due to issue with nest thermostat at no cost. Upon departure system is working and operational.

Combo Tune Up Performed- performed maintenance on 2021 Lennox system. Upon arrival system is working and operational. I began my maintenance at the outdoor unit by breaking it down and cleaning with water and solution. Removed heavy amounts of dirt and debris. I then inspected all electrical components for signs of wear and checked for tight connections. I measured amp draws and recorded refrigerant pressures. I then proceeded to the indoor furnace unit. Here I took temperature splits and measured static pressures. I inspected the condensate lines for proper drainage. I checked electrical components for tight connections and wear. Inspected the blower housing for balance and dust. Checked heating components for wear. Inspected heating components for proper operation. Filter has been checked and does not need to be changed at this time. Upon inspection of both units I found there to be no form of electrical protection on either unit, recommend adding surge protection to both units to pr

Upon arrival performed heating maintenance. Have been here previously, have done repairs and cleanings. Advised client, to replaced filter every 1-2 months due to where house is located. Advised if we do not replace filter we will start going back to what happened before, parts and motors failing due to dirty systems. Dirty filters. Replaced filter, dusted off electrical connections. Secondary motor control is out of range and needs replacement. Client left to work, wanted email. Will follow up with client. System is operational. Client doesn’t use heat a lot due to high propane costs. Advised moving to all electric heating and cooling can possibly be an option.

Upon arrival performed heating maintenance. Have been here previously, have done repairs and cleanings. Advised client, to replaced filter every 1-2 months due to where house is located. Advised if we do not replace filter we will start going back to what happened before, parts and motors failing due to dirty systems. Dirty filters. Replaced filter, dusted off electrical connections. Secondary motor control is out of range and needs replacement. Client left to work, wanted email. Will follow up with client. System is operational. Client doesn’t use heat a lot due to high propane costs. Advised moving to all electric heating and cooling can possibly be an option.