Menifee, CA

Client has to think over membership, they are out of work and can’t do membership. Wanted to do the very basic tk get system up and going. Replaced igniter and got system gojng. Blower wheel is very dirty and needs cleanings. Inducer motor sounds really high pitched. Bearing might be going out.

Client has to think over membership, they are out of work and can’t do membership. Wanted to do the very basic tk get system up and going. Replaced igniter and got system gojng. Blower wheel is very dirty and needs cleanings. Inducer motor sounds really high pitched. Bearing might be going out.

Upon arrival performed maintenance on heating system. Heat exchangers have a lot of heat impengments, metal is getting very weak. Inducer draft motors on both systems are over amping. Indoor blower wheels are very dirty. Circuit boards have some burnt spots in between terminals. Temp rise on systems are close to 55. 55 is the max, but they are getting very close. Ducting is sealed properly. Systems are operational, are older but working ! Client has an appointment for next week for some relaxmwnt options. To utilize solar and no more gas.

Upon arrival performed maintenance on heating system. Heat exchangers have a lot of heat impengments, metal is getting very weak. Inducer draft motors on both systems are over amping. Indoor blower wheels are very dirty. Circuit boards have some burnt spots in between terminals. Temp rise on systems are close to 55. 55 is the max, but they are getting very close. Ducting is sealed properly. Systems are operational, are older but working ! Client has an appointment for next week for some relaxmwnt options. To utilize solar and no more gas.

Upon arrival performed maintenance on heating system. Heat exchangers have a lot of heat impengments, metal is getting very weak. Inducer draft motors on both systems are over amping. Indoor blower wheels are very dirty. Circuit boards have some burnt spots in between terminals. Temp rise on systems are close to 55. 55 is the max, but they are getting very close. Ducting is sealed properly. Systems are operational, are older but working ! Client has an appointment for next week for some relaxmwnt options. To utilize solar and no more gas.

Upon arrival performed maintenance on heating system. Heat exchangers have a lot of heat impengments, metal is getting very weak. Inducer draft motors on both systems are over amping. Indoor blower wheels are very dirty. Circuit boards have some burnt spots in between terminals. Temp rise on systems are close to 55. 55 is the max, but they are getting very close. Ducting is sealed properly. Systems are operational, are older but working ! Client has an appointment for next week for some relaxmwnt options. To utilize solar and no more gas.

Arrived on site to perform fall tune up on 2 2015 carrier units located in attic. Client stated no issues both units working good and heating. Cycled both. Found all filter to be a bit dirty today and client had 4 prepaid ones but stated she would like them replaced on her summer visit and no filters were replaced. Blower assembly are both good and motors are good as well. Both inducer motors are both good and heating. All safety switches are operational. No sediment traps on both gas lines and recommended adding them for prevent issues to gas valve. Temperature rise is good on both units. Drain lines are all good on both units but advised both are good but no safety overflow switches on unit and recommended adding them to prevent over flow in attic and water damage to ceiling. Advised no protection equipped on unit and recommended adding surge protectors on unit to protect from electrical and power outages that can damage or even short out systems and components. Cycled both unit and

Upon arrival started tune up of system. Cleaned out electrical and ,ensured amps. Checked heat rise and static. Flame sensor should be replaced soon. Blower wheel is dirty. Unit is operational.

Installation of new start collar and full length duct run, installing tywe to branch air flow apart for the 2 supply cut ins.

Upon arrival, started install of service valve. Recovered the existing refrigerant. System had 3 lbs. removed old service valve. Welded on new valve while purging nitrogen. Pressure tested system. Pulled vac on system. Added charge. System is now cooling properly.

Performed service on a 2020 Lennox gas furnace. Customer reports system turning on and off. This was confirmed. Found flame sensors to be very corroded. Also found heat shield might cause an issue in the future. As for today the today the sensors were cleaned and tested to get the unit up and running. This is a standard maintenance procedure, the customer is aware of the consequences of going without maintenance. His wife will make the decision o. A scheduled maintenance program, she is not present today. System is operational at end of appointment.

Arrived on site to perform heating tune up on 2 package units. One original to home and other 2007. Filters were dirty recommended replacing every 3 months. Blower assembly on both units have dirt accumulating on wheels creating high stress and causing motors to work harder. Recommend cleaning blower assembly’s on both units. Main unit blower is okay no oil. Added on unit is starting to leak oil as there is layer of oil and dirt accumulating. Found inducer motor have been working really hard as they both have inducer motors covered in oil from over working in its past years. Amp drawls are high on inducer motors just indicating self wear and could fail in future due to condition and working hard. Recommend replacing inducer motor before they completely fail and heaters will not operate properly. Drain lines are good and running of of ceiling. Inspected both heat exchanger ps. Main home unit has a lot of heat impingement as well as hot spots forming. Theses areas are more like to deve

Upon arrival performed leak check. Check evap coil and line set. Client said pervious company put in leak dye. Checked for dye and didn’t find any. Used electronic leak detector to trace a leak to the service valve. Checked entire condenser. Gave clients options. Client went forward with replacement of service valve

Performed heating maintenance on a 1996 Rheem gas furnace. This is a tenant home. Thermostat programming was changed per customers request to a more user friendly program. Filter is clean. Upon inspection I found the blower door is laying on the attic floor. The bracket for gas valve is broken from the welds which caused the door to fall off and not be able to fit back on. This needs to be replaced. The ignitor is in poor shape and is taking over 20 seconds to light. Flame sensor was cleaned and tested. Shutoff valve was tested. The primary blower is leaking oil and overheating which can cause failure of operation in the future. Due to the age of the system typically a Heat exchanger safety test is performed, the homeowner was notified of this and the test was declined due to risk of failure. In the meantime she is purchasing low level CO detectors until next year when she does want a full safety inspection. homeowner were briefed of the condition. System is operational at end of appoi

Replaced the intake air orifice and tested the system. Heat sounds normal, client is going to try it for awhile and let us know how it runs.

Performed furnace maintenance on 2020 Lenox System. upon arrival homeowner was not home. Perform safety inspection and electrical checks. System checked out properly. Static and temperature rise are in range. Flame sensor and igniter in good condition sensor was cleaned also. Homeowner will be ordering filters and calling us back to install for $29. Indoor blower motor and air mix cabinet are in good condition. Upon departure system is fully operational and heating

Performed fall maintenance on a Lennox heat pump in menifee. Indoor unit amps draws are in range. Sensors and switches were cleaned and tested. Blower wheel is clean. Indoor coils are clean. Heating temperature split is 25 degrees. Filter is clean at this time. Outdoor unit was chemically cleaned. Service panel and compressor bay was cleaned. Major component amp draws are in range. Refrigerant levels were checked and verified to be within spec. Discussed air health with client. System is operational.

Upon arrival found system operational. Previously did repair on the control board. Checked motors and ignition process. Unit is operating good. No mechanical issues. Found some design issues. B vent has been rigged. No safety issues found with it. Flood protection and filtration are poor. Talked about current replacement promotions. Made some recommendations. Unit is operational upon departure.

Performed maintenance on a pair of Lennox gas furnaces. Customet changes filter every 30 days. Downstairs unit is heating 50 degree split. Static is higher than spec requests. Blower motor and inducer motor are amping in range. Battery for the primary blower is out of range. Blower wheel is dirty. Heat exchanger was inspected for damage. Sensors and switches were cleaned and tested. Gas valve was tested. The ignitor has a long delay. The flame rollout on ignition was significant, this is indicative of its age and cause for concern. Upstairs unit heating temperature split is in range. Combustion blower is amping high. The ignitor has a big delay as well. The rollout is also significant and should be monitored yearly. Electrical components were tested and recorded. The condition of the unit was discussed with the homeowner. Husband and wife are setting up appointment to go over equipment replacement with us.

Quality control check

Performed maintenance on a 2014 Lennox gas furnace in menifee. Homeowner reports good usage of the furnace this winter with no faults. Homeowner also reports selling the house, his next maintenance will be with new homeowner. I am leaving information for the next homeowner as well. Systems heating temperature rise is in range. Sensors and switches are cleaned and tested. Gas valve and ignitor were tested. Filter is ok today. Blower wheel is very dirty and needs to be pulled and cleaned. The condition was explained to the homeowner Mark. System is operational at end of appointment.

Performed furnace maintenance on 2016 aireflo heater. Client states that system has been working properly. Swapped both upstairs and downstairs filter out. Heating maintenance checked out good. Flame sensor was clean and hot surface igniter is in the proper range. Drain lines are clear coming off inducer motor. Gas valve is opening and closing properly. Indoor blower and scroll wheel are in good clean condition at this time. Flood protection was equipped into the system. Temperature rise and static are in range. Presented and informed the full condition of the 2016 heater and client is aware. System was reset and tested, fully operational upon departure.

Performed service on a 2015 Trane package unit. Customer reports install by next gen. System has always had issues since install. Found unit to be low. Charged system to spec. Added leak dye with a return visit. Customer signed up with our program. System is operating at end of appointment.

Upon arrival found system operational. Client said the thermostat started reconnecting and then it wouldn’t operate. Client reset the stat and it began to operate. Checked operation and cycled unit. No immediate issues found at this time. Advised client on thermostat replacement options and replacement rebates. Unit is operational upon departure.

Upon arrival found 1 7 year old system. Installed by rite time. 3 Ton Lennox. Unit is in good condition mechanically. Tested heating operation only. No issues found with heater. Made recommendations to adjust airflow to master bedroom. Client said unit has a leak and he filled it up a couple times. Previous company MIGHT have added leak dye. Client needs to look for paperwork. If it has dye in it we can come out for a fee and search for it. Will need to check for leak in next visit regardless. Unit is operational upon departure.