Menifee, CA

Furnace ran in heating mode to burn off oil residue from installation. Installers didn’t run system in heating after installation. Owners ran in heating themselves and were startled by smell and smoke alarms. I told them it’s normal for this to happen while running in heat. I stayed and waited for hour to assure no issues to system. No gas leaks or nothing harmful at furnace. There wasn’t any electrical burning or rubber burning. Just a procedure that should have been done to run furnace. No charge today, warranty call on heater.

Arrived on site to perform furnace diagnostic on 2019 heater. Upon arrival client stated that they moved and 2021 And have had many renovations done. She stated that just last night the unit turned on and is no longer heating. Immediately Saw diagnostic code indicating that limit switch was tripped and on a three hour lockout. Reset furnace and removed heavily clogged filter that caused unit to overheat. Client also stated that three bedrooms getting very little airflow proceeded to inspect ducting and found that it was all rectangular ducting encased beneath the studs of the house ceiling. Advised that closing select vents may push airflow to those rooms due to the obsolete design this makes it difficult to work with the duct work in place. Client sign up on maintenance plan to keep both unitary standard twice a year and will be getting new filter at Lowe’s today upon departure unit is operational and heating

Performed maintenance on Goodman unit. Replaced filter, provided by homeowner. Cycled system for heating. Verified proper heating sequence of operations. Temperature rise across heat exchanger is on higher end of allowed maximum. Ran system through 20 point inspection checklist. Checked all heating safeties. Cleaned sensors. Opened coil to inspect heat exchanger. Inducer amperage is above rated maximum, and motor is also louder than normal. Gas line does not have a sediment trap, and condensation lines do not have any safety switches to prevent from ceiling damage. Went over findings and recommendations with homeowner. Wants to hold off on any repairs as system is heating. Cycled system, system is operational upon departure.

Performed a hearing maintenance on a 2019 aire-flo system. Cleaned and Adjust Burners. Check Combustion Air for Proper Venting. Examine the Heat Exchanger for Damage / Corrosion. Test Furnace Safety Controls. Inspect Gas Piping. Tighten Electrical Connections. Measure the Voltage and Amperage. Flush the Condensate Drains. Measure Tempurature Difference between Supply and Return Air. Vacuum Furnace Return Grille. Adjust Gas Pressure & Pilot. Clean in-place Blower Compartment. Inspect Blower Wheel for Proper Balance. Check the System's Static Pressures to Ensure Proper Airflow. Inspect Duct Connections for Air Leaks / Sizing / Insulation. Check all System Safety and Limit Switches. Clean Flame Sensor. Inspect Carbon Monoxide Detector. Check Thermostat for Proper Operation / Calibration.

Upon arrival performed maintenance. Did cleanings on flame sensor. Indoor blower wheel and caging very nice and clean . Circuit board and electrical connections in range. Advised client he is slacking airflow on return side. Pretty upset that it wasn’t brought up during the time of sale. Apologized and gave the solution of adding the return with the price of during install price. System is in very good condition. Client will give us a call if he decided to do cut in. All other electrical components are good and healthy. Ducting is sealed and secured. Need to extend plenum if adding another return.

Upon arrival performed maintenance. Did cleanings on flame sensor. Indoor blower wheel and caging very nice and clean . Circuit board and electrical connections in range. Advised client he is slacking airflow on return side. Pretty upset that it wasn’t brought up during the time of sale. Apologized and gave the solution of adding the return with the price of during install price. System is in very good condition. Client will give us a call if he decided to do cut in. All other electrical components are good and healthy. Ducting is sealed and secured. Need to extend plenum if adding another return.

Upon arrival performed maintenance. Did cleanings on flame sensor. Indoor blower wheel and caging very nice and clean . Circuit board and electrical connections in range. Advised client he is slacking airflow on return side. Pretty upset that it wasn’t brought up during the time of sale. Apologized and gave the solution of adding the return with the price of during install price. System is in very good condition. Client will give us a call if he decided to do cut in. All other electrical components are good and healthy. Ducting is sealed and secured. Need to extend plenum if adding another return.

Upon arrival performed maintenance. Did cleanings on flame sensor. Indoor blower wheel and caging very nice and clean . Circuit board and electrical connections in range. Advised client he is slacking airflow on return side. Pretty upset that it wasn’t brought up during the time of sale. Apologized and gave the solution of adding the return with the price of during install price. System is in very good condition. Client will give us a call if he decided to do cut in. All other electrical components are good and healthy. Ducting is sealed and secured. Need to extend plenum if adding another return.

Arrived on site to perform heater diagnostic on 1999 package unit. Upon arrival David stated that he recently turned the heat on and noticed that it was not warming up the house verified the thermostat are working correctly it has a zoned package unit. Began diagnostic on package unit and found that inducer motor is running although gas valve is not releasing gas through the pilot tube resulting in no ignition. Tried troubleshooting valve to get it to kick on although nothing happened. Inspected heat exchanger and found significant heat spots although no visible cracks at this time. The heat spots developed due to the improperly zoned system on a one stage package unit and undersize return intakes. Inspected indoor blower motor as well and found significant oil leakage from its bearing which will lead to it locking up or overheating in the future. Inspected attic ducting and found ripped duct running to kitchen resulting in no airflow. Presented full diagnostic report to David and he i

Replaced breaker and fuses, insulated lineset.

Upon arrival performed maintenance on old heating system. Client wanted me to check coming first. Compressor is running over 31.3 amperage’s & shut off due to overheating. Client just purchase home 1 year ago gonna see if they have home warranties. Advised we do have 6/12/18 no interest same as cash options. System is very old temp rise is very close to max. This means the heat exchanger inside of the system can be damaged. Was not able to inspect heat exchanger due to package unit curb. Dusted off burners and electricals. System doesn’t really keep up with the heat in summer time. System is operational. Client is gonna check with home warranties. Client added solar to home to help with energy bills. Will follow up with carol.

Upon arrival performed maintenance on old heating system. Client wanted me to check coming first. Compressor is running over 31.3 amperage’s & shut off due to overheating. Client just purchase home 1 year ago gonna see if they have home warranties. Advised we do have 6/12/18 no interest same as cash options. System is very old temp rise is very close to max. This means the heat exchanger inside of the system can be damaged. Was not able to inspect heat exchanger due to package unit curb. Dusted off burners and electricals. System doesn’t really keep up with the heat in summer time. System is operational. Client is gonna check with home warranties. Client added solar to home to help with energy bills. Will follow up with carol.

Upon arrival performed maintenance on old heating system. Client wanted me to check coming first. Compressor is running over 31.3 amperage’s & shut off due to overheating. Client just purchase home 1 year ago gonna see if they have home warranties. Advised we do have 6/12/18 no interest same as cash options. System is very old temp rise is very close to max. This means the heat exchanger inside of the system can be damaged. Was not able to inspect heat exchanger due to package unit curb. Dusted off burners and electricals. System doesn’t really keep up with the heat in summer time. System is operational. Client is gonna check with home warranties. Client added solar to home to help with energy bills. Will follow up with carol.

Upon arrival performed maintenance on old heating system. Client wanted me to check coming first. Compressor is running over 31.3 amperage’s & shut off due to overheating. Client just purchase home 1 year ago gonna see if they have home warranties. Advised we do have 6/12/18 no interest same as cash options. System is very old temp rise is very close to max. This means the heat exchanger inside of the system can be damaged. Was not able to inspect heat exchanger due to package unit curb. Dusted off burners and electricals. System doesn’t really keep up with the heat in summer time. System is operational. Client is gonna check with home warranties. Client added solar to home to help with energy bills. Will follow up with carol.

Arrived on site to preform furnace maintenance on manufactured home heater. Upon arrival client Stated heater has been working fine and if anything is wrong to let her know but can’t do anything as of this time. Preformed safety inspection on heater. Temp rise was in range. Indoor blower motor is really dirty and in need of deep cleaning. Circuitboard has major burn marks on resistors. Recommend surge protection to prevent further damage to main control board. Filter were also swapped out. Discussed full condition with client and she is aware of condition of unit. Upon departure heater is fully operational and heating

Performed FAU tuneup on 2 year old Lennox unit. Cleaned return grates. Cleaned condensate drain P trap and flushed with water. Installed new owner-supplied merv 11 filter. Tested external static pressure. Inspected blower compartment, blower wheel is clean and balanced. Inspected electrical connections. Cleaned flame sensor. Tested resistance of hot surface igniter. Temperature rise is within limits. Tested all safety switches. Upon departure system is operational.

Performed FAU tuneup on 2 year old AC Pro unit. Cleaned return grate. Replaced filter with new owner-supplied merv 16 filter. Cleaned condensate drain P trap and flushed with water. Tested external static pressure. Inspected blower compartment, blower wheel is clean and balanced. Tested all safety switches. Cleaned flame sensor. Tested resistance of hot surface igniter. Temperature rise is within limits. Inspected electrical connections. Upon departure system is operational.

Technician arrived to perform furnace tune up for 1 year old system -Flame sensor and igniter cleaned off -Inducer motor reading proper amps and resistance -Igniter has good resistance -Blower motor has low amps -Filter was very dirty, it was replaced -Blower compartment is still very clean -Dampers were adjusted to ensure clients have well balanced air flow

Arrived on site to perform Heating tune up on a 2003 Goodman unit. Client stated nonissues as he is yet to run heater. Client stated he has Edison come out and replace thermostat and he stated new computer board and since then hasn’t had a issues. Cycled unit and unit was operational. Filter was really dirty but client stated he went and bought a washable filter and will be washing it himself. Inspected attic and found black flex ducting used and okay. Blower assembly and whee have dirt build up from filter not getting replaced or washed as needed. Motor has been leaking oil in past from working hard. Found secondary motor control in blower out of range and going bad. Motor is causing it to drain. All safety switches are operational. Temperature rise is in range. Drain lines are dusty due to dirt that has entered unit. Flame sensor is oxidizing and getting discoloration and No protection on unit and recommended surge protection to protect unit from electrical surge and power outages.

Arrived on site to perform heating tune up on a lennox unit. Flame sensor was replaced and unit is now operational. Cycled heating and stayed running. Filter were just replaced by client recently. Black flex ducting used and is okay. Unit is zoned and is single stage. Blower assembly is dusty. Motor is good and in range. Secondary motor is good and in range. Inducer motor is running in range. Temperature rise is good and in range. Drain lines is good at this time. Temperature is in range. Static pressure is good. Advised just a bit dusty and recommended a phenomenal air to help keep unit and home clean and dusty from building up and improve the air quality in hole for anyone with allergies. Client is aware. Cycled unit and unit ai operations. Went over recommended and client did hold off for now. Cycled unit and is operational in heating nowb she is happy we came out today.

During my twenty point heating inspection, I started with the thermostat. Giving a call for heating, and going to furnace to start maintenance. Temp rise of 30-60 needed, I got a temp rise of 40. House heats up to designated temperature. I checked out blower motor of any dirt or debris and it’s clean. Air filter needs to be changed, but owner said they’d buy new one them selves. Hot surface igniter not cracked or having white spots. Flame sensor still working good, no need to be cleaned. Ducting done correctly, and all runs intact. Inducer motor is working efficiently. House heats good and ready for winter.

During my twenty point heating inspection, I started with the thermostat. Giving a call for heating, and going to furnace to start maintenance. Temp rise of 30-60 needed, I got a temp rise of 56. House heats up to designated temperature. I checked out blower motor of any dirt or debris and it’s clean. Hot surface igniter not cracked or having white spots. Flame sensor still working good, no need to be cleaned. Ducting done correctly, and all runs intact. Inducer motor is working efficiently. House heats good and ready for winter.

Technician arrived to perform furnace tune up -Filter was replaced, homeowner supplied -Flame sensor and igniter were cleaned off -Inducer motor has proper resistance -Blower motor is clean and drawing correct amps -Electrical connections tightened down -Everything is firing up nicely

Upon arrival unit was operational. Checked amps they were in range checked temp rise it was in range, condensation line was clogged, blew it clear, blower wheel was free of oil and clean, safety switches were functioning properly. Burners were clean and flame sensor was cleaned. Upon departure unit was operational and heating.

Arrived on site to perform maintenance on a 12 year old heater. Client stated no issues that she knows of as he has yet to run the heater this year. Cycled heater on with both zones. Waited to hear unit turn on and get operational and heating. Could not hear unit as heater is not heating up or completing the heating sequence. Found unit tripped and locked out due to no flame. Inspected unit and cleaned off flame sensor. Cycled again and found unit not operational advised unit turns on and flame is created but then shuts off as of it was not sensed. Advised client ha s a bad flame sensor and it’s keeping unit from turning on. Would have to special order and client did want to go forward with replacing flame sensor. Advised office will call one part arrives. Advised heater is not going to be operational but Ac will if she needs it. Was not able to do maintenance and she is okay with is as I’ll do it when I come back for repairs. She is okay with so.