Menifee, CA

Client had thermostat not full pushed in. Thermostat wires were blocking entry. Client declined Memebrship. Does not have funds . Tested multiple Times system is operational. Please send paper copy to mail .

Client had thermostat not full pushed in. Thermostat wires were blocking entry. Client declined Memebrship. Does not have funds . Tested multiple Times system is operational. Please send paper copy to mail .

When I arrived, I was told thermostat didn’t work. Thermostat was fully functioning and receiving 24volts. I then went up to furnace and saw that system kept failing after re trying consistently. Error codes told me that inducer is malfunctioning, but that also pressure switches are faulty. I checked all my pressure switches and all were working. Although they were clicking in and out when starting. I took off all hoses to pressure switches and found water in two of the hoses. This indicates that there may be water in pressure switches. Causing system to fail repeatedly. Took off inducer motor, to see if there was any water inside. Inducer didn't have water inside. Burners only lit for a couple seconds than would shut off. I had two inches of water in drain pan. There should be no water in pan, so there is a water leak somewhere in system. Today we will just be charging for diagnostic, since I wasn’t able to fix problem. I spoke with supervisor and after the owners find booklet of

During my twenty point heating inspection, I started with the thermostat. Giving a call for heating, and going to furnace to start maintenance. Temp rise of 40-70 needed, I got a temp rise of 45. House heats up to designated temperature. I checked out blower motor of any dirt or debris and it’s clean. Replaced air filter for new air filter. Owner had extra one, so just used his. Hot surface igniter not cracked or having white spots. Flame sensor still working good, no need to be cleaned. Ducting done correctly, and all runs intact. Inducer motor is working efficiently. House heats good and ready for winter.

Performed heating maintenance on 4 year old Lennox package unit. Cleaned return grate. Flushed condensate drain line with water. Inspected blower compartment, found blower wheel to be clean and balanced. Inspected flame rod. Temperature rise is normal. Tested all safety switches Upon departure system is operational.

Upon arrival performed diagnostic. Client needed help knowing how to use thermostat , it is always so complicated. But she took notes of me explains how to use. System is operational

Upon arrival performed diagnostic. Client needed help knowing how to use thermostat , it is always so complicated. But she took notes of me explains how to use. System is operational

Upon arrival performed diagnostic. Client needed help knowing how to use thermostat , it is always so complicated. But she took notes of me explains how to use. System is operational

Upon arrival performed diagnostic. Client needed help knowing how to use thermostat , it is always so complicated. But she took notes of me explains how to use. System is operational

During my twenty point heating inspection, I started with the thermostat. Giving a call for heating, and going to furnace to start maintenance. Temp rise of 40-70 needed, I got a temp rise of 46. House heats up to designated temperature. I checked out blower motor of any dirt or debris and it’s clean. Replaced air filter for new air filter. Owner had extra one, so just used his. Cleaned owners filter grill of all debris. Hot surface igniter not cracked or having white spots. Flame sensor still working good, no need to be cleaned. Ducting done correctly, and all runs intact. Inducer motor is working efficiently. House heats good and ready for winter.

Upon arrival inspected filter home owner stated it was recently changed and look good. Checked electrical components for high amp draws and all were within their thresh hold limit. Cleared condensate drain and flushed it with water. Took static pressure and temp rise both looked good. Blower wheel was balanced and cleaned off. All the gas piping look good with no leaks.

During my twenty point heating inspection, I started with the thermostat. Giving a call for heating, and going to furnace to start maintenance. Temp rise of 40-70 needed, I got a temp rise of 42. House heats up to designated temperature. I checked out blower motor of any dirt or debris and it’s clean. Replaced air filter for new air filter. Owner had extra one, so just used his. Hot surface igniter not cracked or having white spots. Flame sensor still working good, no need to be cleaned. Ducting done correctly, and all runs intact. Inducer motor is working efficiently. House heats good and ready for winter.

Performed a heating maintenance on a 2021 Lennox system. Cleaned and Adjust Burners. Check Combustion Air for Proper Venting. Examine the Heat Exchanger for Damage / Corrosion. Test Furnace Safety Controls. Inspect Gas Piping. Tighten Electrical Connections. Measure the Voltage and Amperage. Flush the Condensate Drains. Measure Tempurature Difference between Supply and Return Air. Vacuum Furnace Return Grille. Adjust Gas Pressure & Pilot. Clean in-place Blower Compartment. Inspect Blower Wheel for Proper Balance. Check the System's Static Pressures to Ensure Proper Airflow. Inspect Duct Connections for Air Leaks / Sizing / Insulation. Check all System Safety and Limit Switches. Clean Flame Sensor. Inspect Carbon Monoxide Detector. Check Thermostat for Proper Operation / Calibration. Filter was changed this visit. System was fully operational on time of departure.

Technician arrived to perform furnace tune up -Filter was replaced -Igniter and flame sensor cleaned -Inducer and igniter reading proper resistance -Motors reading proper resistance -Electrical connections tightened down -Air purification was recommended to help combat allergies -Heating is functioning properly

Technician arrived to perform combo tune up -Refrigerant levels are within range -Coil is cleaned -Electrical components are all working properly -Filter is clean -Blower motor drawing proper amps -Inducer motor and igniter reading good resistance -Ducting is in good shape and not leaking any air -Electrical connections tightened down -Heating and cooling both running very efficiently

Technician arrived to perform furnace tune up -Igniter and flame sensor cleaned off -Resistance for igniter and inducer is within range -Blower motor is leaking a lot of oil and drawing very high amps (using a lot of power) -Heating is turning on properly -Ducting is in great condition -Zone dampers are opening and closing properly -Blower motor replacement is highly recommended and it is in very rough condition, and drawing a significant amount of power -Capacitor will be replaced along with motor if replaced

Diagnosed defective ecobee thermostat

Performed heating maintenance on Goodman unit. Cycled system for heating. Ran system through 20 point inspection. Verified temperature rise. Replaced filter. Checked heating safeties and electrical. Blower wheel is very dirty, and blower motor has been leaking oil and motor casing is significantly caked in dirt and dust. Homeowner waived heat exchanger inspection for today as he doesn’t not want to risk unit being shut down. Went over findings and recommendations. Homeowner wants to take care of cleaning and replacing motor, but wants to wait until next year. System is operational upon departure.

Need to return with control board

Arrived at house and was told condenser unit wouldn’t turn on. I checked incoming voltage and had no power. I go to breaker panel and the ac unit breaker was tripped. Every time I switched breaker to on position the breaker would trip. I then took off compressor windings off contactor and herm winding and fan motor only turned on. I checked continuity and the leg on compressor is faulty. Charging for diagnostic only today. I clarified problem to owner and is aware of issue.

Performed maintenance on American Standard unit. Cycled system for heating. Verified proper heating sequence of operations. Ran system through 20 point inspect checklist. Went over findings and concerns. Cycled system. System is operational upon departure.

Performed a heating maintenance on a 2017 trans system. Cleaned and Adjust Burners. Check Combustion Air for Proper Venting. Examine the Heat Exchanger for Damage / Corrosion. Test Furnace Safety Controls. Inspect Gas Piping. Tighten Electrical Connections. Measure the Voltage and Amperage. Flush the Condensate Drains. Measure Tempurature Difference between Supply and Return Air. Vacuum Furnace Return Grille. Adjust Gas Pressure & Pilot. Clean in-place Blower Compartment. Inspect Blower Wheel for Proper Balance. Check the System's Static Pressures to Ensure Proper Airflow. Inspect Duct Connections for Air Leaks / Sizing / Insulation. Check all System Safety and Limit Switches. Clean Flame Sensor. Inspect Carbon Monoxide Detector. Check Thermostat for Proper Operation / Calibration. Filter was changed this visit. System was fully operational on time of departure.

Performed a heating maintenance on a 2021 Lennox system. Cleaned and Adjust Burners. Check Combustion Air for Proper Venting. Examine the Heat Exchanger for Damage / Corrosion. Test Furnace Safety Controls. Inspect Gas Piping. Tighten Electrical Connections. Measure the Voltage and Amperage. Flush the Condensate Drains. Measure Tempurature Difference between Supply and Return Air. Vacuum Furnace Return Grille. Adjust Gas Pressure & Pilot. Clean in-place Blower Compartment. Inspect Blower Wheel for Proper Balance. Check the System's Static Pressures to Ensure Proper Airflow. Inspect Duct Connections for Air Leaks / Sizing / Insulation. Check all System Safety and Limit Switches. Clean Flame Sensor. Inspect Carbon Monoxide Detector. Check Thermostat for Proper Operation / Calibration. Filter was changed this visit. System was fully operational on time of departure.

During my twenty point heating inspection, I started with the thermostat. Giving a call for heating, and going to furnace to start maintenance. Temp rise of 40-70 needed, I got a temp rise of 36. House heats up to designated temperature. I checked out blower motor of any dirt or debris and it’s still clean. Air filters were still in good condition and don’t need to be changed at this visit. Hot surface igniter not cracked or having white spots. Flame sensor still working good, no need to be cleaned. Ducting done correctly, and all runs intact. Inducer motor is working efficiently. House heats good and ready for winter.

Furnace didn’t work in heating mode when I arrived. Gas pilot was in off position and put it in ON position. System took about five minutes to get blower motor on and inducer. System took off in heating mode and vents all started heating rooms. No charge today, warranty call. House heats great and ready for winter.