Lake Elsinore, CA

Arrived on site to perform spring tune up on a 2002 weather raking system. Condenser located in back yard, furnace evaporator coil located in attic. Client stated no issues. She cycled cooling mode on. Inspected indoor unit. Checked filters. Checked ducting and insulation. Inspected indoor unit. Checked all electrical wiring, connections, circuit board, and components. Checked blower assembly, wheel, and motor. Checked amps drawls on blower motor. Checked evaporator coil and drain lines. Blew drain line out with drain gun. Checked temperature split. Cycled system. Washed out condenser coil inside and out. Checked fan blades, bearings, and motor. Checked electrical compartment and components. Checked amp drawls on compressor and fan motor. Checked refrigerant pressures. Cycled system to ensure systems operating. The f Summary of findings are as followed. Furnace 1. Filter hammered and replaced. 2 black flex ducting used and good insulation. 3. Blower assembly is really dirty creating h

Inspected both system for faults and performance

Performed AC diagnostic on 2007 Rheem condensing unit. Upon my diagnostic I found that the compressor Had gone out on thermal overload, this is been caused due Due to the wind is going bad on the system measured amperage on compressor was pulling at 11 A which was incredibly high when its max rating was 14.1. Measured refrigerant pressures and found system in noncondensibles inside due to fluctuating pressures. System also contains R22 refrigerant Which was phased out January 1, 2020. Recommended putting compressor saver kit on to give compressor steroid boost on start up due to system failing under load. Raul would prefer replacement options but needs to confirm with his wife. System is non-operational upon departure

Post job walk and picked up portable

Performed tune up on the air conditioning system. Tested thermostat and measured indoor temperatures. Replaced filters. Checked indoor system condensate lines. Tested condenser controls and measured voltages. Measured motor amp draws. Inspected fan motor. Cleaned condenser inside and out, cleaned the outdoor coils with water and cleared all debris from the unit. -System does not have surge protection to protect the outdoor or indoor motors. -Battery cap for the condenser is weak and needs replaced. -Indoor system could be upgraded to improve filtration with a heap grade filter rack and eco blower motor. This would vastly improve the systems home air quality and improve the performance of the equipment.

Performed maintenance on the cooling system. Tested thermostat and replaced filter. Inspected indoor unit ducting and cleared condensate trap. Measured indoor temperature delta. Inspected outdoor system and measured voltages/ motor amp draws. Tested starting and run components. Inspected outdoor fan motor. Cleaned condenser coils and inside condenser bottom. Checked fuses. Tested system before leaving.

Will be injecting leak dye to pinpoint location of refrigerant leak. This will be the first step in determining where your leak may be located. Once I have pinpointed and determined where the leak is located we then could go over cost and repairs to fix refrigerant leak.

Quality control check for a Freon leak

arrived on site to diagnose a 2016 unit that is shutting off and on. Condenser located in back yard. Furnace and evaporator coil located in attic. Some to client she stated she hasn’t maintenance Unit since install. Unit operates and at night time it will shut off and back on 5 minutes later. Went and inspected indoor unit. Found filter completely clogged And was same from install thus creating a lot more condescension and Found secondary safety switch was being tripped and it was on its side. Put switch to sit up right and was good. Found secondary pan with a lot of dried water from past. Advised client her drain lines are probably clogged. Advised Client and she did want to clear drain as she saw the drain at sink was clogged and replace filter. Found evaporator coil connection on primary drain hole that connects to drain lines is leaking. Due to over the years of leaking water it has deteriorated the threads on drain hole on pan and reason why secondary pan has water is startin

Returning to install 2 12 inch dampers To increase airflow to upstairs bedrooms.

Performed AC diagnostic on 14-year-old Lennox Ac system. Upon My diagnostic there were a few points and concerns that were addressed 3 ton Lennox- 1. Found that system was slightly low on 410 a refrigerant 2. Found the compressor saver kit was no longer supporting proper Micro ferrets ratings to keep system healthy. 3. Found the disconnect had no surge protection.

Arrived on site to diagnose 2005 Payne system that is not cooling. Upon arrival spoke to tenants regarding issues and they stated unit will turn on but not cool. Had client turned system on to cooling. Found furnace not operational. Condenser making loud noise. Inspected indoor and out door unit. Checked all electrical connections and components. Checked motor and reading. Advised the summary of finding are as followed. Furnace 1. Filter restricted and clogged from 2016. 2. Blower motor is bad not operational. 3. Blower motor bracket it bad and not straight. 4. Blower wheel is dirty creating wheel to get off balanced. 5.Blower wheel is unbalanced as wheel is running on blower casing. 6. Secondary control is bad and out of range. 7. Has thermostat wire all exposed and at risk of shortage. 8. Found live Possum in furnace and u dear house. Advised owner. Condenser 1. Primary control is all Burnt. 2. Secondary control is bad and below range. 3. Fan motor has oil leaking down shaft

Tested system on the cooling mode and cleaned filters. Inspected the electrical panel and made sure all connections were tight and secure. Measured supply voltages and recorded motor amp draws. Cleaned the outdoor coils and measured indoor temperatures.

Performed AC maintenance on two systems Goodmans 15 years old. Upon my maintenance I came across a few points concerns and they are- Upstairs 3 ton- 1. Found the condenser fan motor is leaking lubricant from bearing and shaft 2. Found that battery Is weak on hermetic side terminal due to compressor pulling high amps 3. High voltage rely showing signs of pitting on contact point 4. Found the compressor was pulling 10 A on 70° day this can be a problem once the summer hits and put the system in a higher risk of failing 5. Fan motor was also over ramping due to lubrication leaking out 6. System extremely low on R22 refrigerant Downstairs 3 ton- 1. Found the condenser fan motor is leaking lubrication from bearing shaft as well 2. High voltage really showing signs of pitting on contact point 3. Fan terminal on the battery cap Rating 5.2 this is considered out of range on data plate 4. Compressor also pulling high amps at 10 also

Arrived on site to perform spring tune up on a 2016 Lennox system. Condenser located in back yard. Furnace and evaporator coil located in attic. Client stated no issues just wanted to get system hacked up on and replace filter. Client tune cooling on. Thermostat was good. Did indoor nit inspection. Insulation is good. Found filter to completely clogged and restricting air flow to system. Advised this is really bad and need to be replacing filter about every 2 months Due to home surrounding by dirt fields. Blower wheel is dirty due to lack of filter change out. Build up is creating stress on motor. Blower motor is good and oil free. Found secondary motor control for blower motor is bad and out of range. Recommend replacing before completely gives out and system will not have any air flow. Evaporator coil is clean at this time. Drain lines are good and clean and draining. Temperature split is in range and cooling. Cycled system to ensure system operating. Washed condenser coil inside an

Drop off room ac

Pre job walk

Replace existing system complete with listed equipment, seal all supply cans and install high flow register set. Seal return air base and skin platform with sheet metal. Permits and HERS included

Cancelled at the door. No show.

Diagnostic is waived, customer opened up system yanked out wires no schematic. System is doing a very loud buzzing noise coming from primary distributor. System is 1987 customer is having financial problems, she will follow up this is her moms house and will see if she can qualify for new system. Waived diagnostic did not touch system system was already opened.

Diagnostic is waived, customer opened up system yanked out wires no schematic. System is doing a very loud buzzing noise coming from primary distributor. System is 1987 customer is having financial problems, she will follow up this is her moms house and will see if she can qualify for new system. Waived diagnostic did not touch system system was already opened.

Diagnostic is waived, customer opened up system yanked out wires no schematic. System is doing a very loud buzzing noise coming from primary distributor. System is 1987 customer is having financial problems, she will follow up this is her moms house and will see if she can qualify for new system. Waived diagnostic did not touch system system was already opened.

Diagnostic is waived, customer opened up system yanked out wires no schematic. System is doing a very loud buzzing noise coming from primary distributor. System is 1987 customer is having financial problems, she will follow up this is her moms house and will see if she can qualify for new system. Waived diagnostic did not touch system system was already opened.

Performed AC maintenance on 14-year-old 5 ton in 2 1/2 ton condensing . unit. During my meetings I came across a few points or concerns that were addressed and documented. 5 ton- 1. Found the disconnect terminals melted into line voltage and load keeping system under 120 volts on one leg on contractor. 2.5 ton- 1.System contains R22 refrigerant which was phased Jan 1 2020 2. Disconnected not contain any fuses or surge protection 3. Contactor showing signs of pitting on contact point 4.Fan motor pulling below amps and compressor 5.System appear to be overcharged slightly

2 system ac maintenance