Lake Elsinore, CA

Replaced defective induce draft motor. Adjusted low fire gas valve pressure to 1.6 inWc. Measured temperature rise at 32F.

Heating maintenance and service testing. Checked all heating electrical components and safeties. Inspected blower and burner assembly. Wiped dust from interior. Tested amp draws. Measured temperature rise. Replaced filter.

Inspected system for faults and ordered replacement motor from Lennox under warranty.

Performed furnace maintenance on seven-year-old amana heater. Upon my maintenance I replaced the Bryant humidifier filter. Noticed a couple small points of concerns that were addressed with Joe. 1. Found that evaporator coil Had a large amount of air leakage Occurring due to old tape peeling off. Re-sealed system and air leakage is been sealed 2. Found that flame sensor was oxidized and had a carbon buildup. Clean sensor off although sensor can fail due to the oxidization 3. Indoor blower cabinet is heavily covered in dust and debris. This can be a trigger for allergies and ruin longevity of the system. 4. ECM motor a slight dirt buildup as well. Most of the dirt is collected on the scroll wheel it has a potential to throw the scroll wheel off balance if dirt buildup becomes much more greater. 5. 1 inch filter needs to be swapped out every 1 to 3 months to prevent dust buildup 6. System is not equipped with surge protection Upon departure system is fully operational heating home

Performed routine fall maintenance on Goodman furnace in lake Elsinore

Performed furnace maintenance on 2005 Gibson heater. During my maintenance I noticed a few things that were of concern. 1. Found that heat exchanger had multiple heat spots and outer layers beginning to peel off of tubular exchanger. This is due to overheating caused by low Airflow, this can unfortunately cause the heat exchanger to crack. 2. Indoor blower cabinet is covered in dust and debris due to 1 inch filter inefficiently stopping dust particles. Recommended that a cleaning is done to ensure a sanitized and clean air cabinet present. 3. Evaporator coil has Lint and dust It’s collecting within causing a blanket the form 4. Hot service igniter is at 96 ohms. This is due to the heat spot that is formed which will eventually lead to crack causing a failure on ignition. 5. Flame sensor has oxidized but was cleaned has major wear and tear 6. Heat rises is at 61 degrees. This must be watched closely and does not exceed 70 filter must be swapped at least four times a year to prevent a

Performed furnace maintenance on 2007 Lennox heater

Tested zone sensors for faults and ran system on both heating and cooling modes. Tested individual zones and verified voltages at thermostats.

Performed furnace maintenance On 2010 Lennox system. Upon my maintenance there were a couple points of concerns that were addressed with homeowner. 1. Found that water leakage may have been coming from collector-box or secondary He change it also did not find any signs of cracks on the plastic or within the heat exchanger this could be from the past 2. Air restriction is very high on the system due to it being zone and it’s only a one stage 90% furnace. Typically it’s recommended to have a two-stage furnace when you have zoning due to airflow problems 3. Found the indoor blower motor is beginning to over amp due to oil leakage from bearing this may cause the motor to lock up or over heat. 4. Single secondary motor control is becoming weak due to motor using too much power 5. Scroll wheel is becoming kicked in dust and debris due to 1 inch filter is not filtering out dust particles efficiently recommend that filter rack is installed to increase filtration

Quality control check

Post job walk a d gift bag

Tested system for faults and diagnosed defective low voltage fuse, replaced fuse and mounted thermostat to wall.

Performed Fau maintenance on 2 15 year old Aireflo units. Based on the notes customer had some issues with the AC over the summer. She had the upstairs unit replaced by a different company over the summer. When I asked her why and she explained I believe there was a miscommunication in what we were selling her compared to the company that she gave the job too. Cycled furnaces for heat. Checked indoor units electrical and system components. Both blower motors are leaking oil and are working fairly hard. Indoor blower wheels are both dirty. Recommended for filters to be changed out more frequently to prevent added stress and dirt on blower wheels. Cleaned out blower compartment and heating compartment. Tested heating safety operations, system has proper heating sequence. Pulled off blower wheel and evaporator coil to take a look at heat exchanger. Took pictures of hot spots and heat impingements. Ductwork is pretty old and is all original to the home as well as the furnaces. Homeowner is

Inspected system for functionality.

Inspected heating system and tested equipment. Measured indoor temperature split. Recorded voltages and motor amp draws. Measured ignitor in ohms. Cleaned flame sensor. Wiped blower cabinet. Tested blower run capacitor. Cleaned and adjusted burners.

Returned to install second motor. Motor has been installed and system is cooling fully operational upon departure

Performed system diagnostic due to nest installation accident. Upon my diagnostic I found that both nest thermostat on a two zone system had no power. I proceeded into the attic and found that the Lennox zone board Had a blown fuse, replaced fuse and power returned back to both thermostats. Also took a static pressure reading across furnace and found that system airflow is at 0.75 one specification and Sarah 0.50 this is due to low airflow. Temperature rise is also above 60 Indicating to me that system is getting very hot. Multiple locations where water has leaked out maybe due to Breached secondary Need to return and schedule furnace maintenance to inspect system

Preformed Ac and furnace maintenance

Performed furnace maintenance on 2 15 year old York units. Cycled systems for heat. Checked indoor units electrical and system components. Temperature rise across heat exchangers is within range for both systems. Blower wheels have slight dust build up. Indoor blower motor amperages are slightly high, but within range. Cleaned off blower and heating compartments. Pulled blower motors off to thoroughly inspect heat exchangers. slight visible hot spots on tubes. Systems have duct board plenums, which have fiberglass. Homeowner has sensitive nose, and duct board plenums can be a huge factor in poor indoor air quality. Primary and secondary Drain pans on upstairs unit are very rusted out and are leaking. Would recommend replacing at least secondary drain pan to prevent ceiling damage from water leaking through. Replaced 1 inch filters. Systems are in working condition, but are getting oldEr and are super Inefficient. Went over full system findings as well as options, including system,repl

Performed Furnace diagnostic on 17-year-old Goodman system. Upon my diagnostic there were a few points or concerns. 1. Found the circuitboard within furnace was experiencing intermittent behavior and was producing a chattering noise within the relays. Ultimately caused the inducer and the indoor fan motor to shut on and off. 2. Indoor blower motor was showing oil leakage from bearing. This can cause the fan motor to lock up and over amp 3. Motor control for capacitor was replaced once as well 4. Airflow was rating .80 exceeding the .10 designed for it on data plate. This could indicate airflow restrictions interfere with heat exchanger Recommendations- 1. Replace circuitboard with aftermarket board to prevent intermittent behavior 2. Replace condensing fan motor to prevent motor lock up

Replaced one motor, need return for 4 ton motor

Upon arrival performed maintenance on 2 furnace units. Temp splits very good. Both indoor moto in great condition. Secondary motor controls in range. Circuit board and electrical connections good. Recommend adding surge protection. Customer declined work. Cycled systems on and off. Sequence of heating in good condition. Electrical dampers in working order. Replaced 1 filter. Did not have 2 20x30x1. Hclient wanted to do heating tune up. Systems were reset tested and fully functional upon departure. Duct seals good. Insulation levels good.

Upon arrival performed maintenance on 2 furnace units. Temp splits very good. Both indoor moto in great condition. Secondary motor controls in range. Circuit board and electrical connections good. Recommend adding surge protection. Customer declined work. Cycled systems on and off. Sequence of heating in good condition. Electrical dampers in working order. Replaced 1 filter. Did not have 2 20x30x1. Hclient wanted to do heating tune up. Systems were reset tested and fully functional upon departure. Duct seals good. Insulation levels good.

Upon arrival performed maintenance on 2 furnace units. Temp splits very good. Both indoor moto in great condition. Secondary motor controls in range. Circuit board and electrical connections good. Recommend adding surge protection. Customer declined work. Cycled systems on and off. Sequence of heating in good condition. Electrical dampers in working order. Replaced 1 filter. Did not have 2 20x30x1. Hclient wanted to do heating tune up. Systems were reset tested and fully functional upon departure. Duct seals good. Insulation levels good.

Upon arrival performed maintenance on 2 furnace units. Temp splits very good. Both indoor moto in great condition. Secondary motor controls in range. Circuit board and electrical connections good. Recommend adding surge protection. Customer declined work. Cycled systems on and off. Sequence of heating in good condition. Electrical dampers in working order. Replaced 1 filter. Did not have 2 20x30x1. Hclient wanted to do heating tune up. Systems were reset tested and fully functional upon departure. Duct seals good. Insulation levels good.