Lake Elsinore, CA

Arrived on site to perform diagnostic on 10 year old unit. Met with Michael. On arrival, Michael let me know that he was the tenant, verified that we had homeowner permission to be on site to which he said he had homeowner permission. Depending on repairs Michael will be taking care of payment and then taking care of it with homeowner. Thermostat is black and cooling is not working. Checked for power at thermostat and there is no power coming to thermostat. Went into attic and found furnace had a blown fuse. Replaced fuse and immediately blew again. Checked wiring and found the wire going to the condenser to be shorted out. Wire to condenser Needs to be rewired. With Michaels approval went ahead and re wired low voltage command from condenser and furnace. Upstairs Thermostat now has power and unit is cooling. Michael did let me know that unit has a leak at the evap coil that has been diagnosed by another company. They fill the refrigerant once a year. I checked pressures and they are

Performed furnace maintenance on a Lennox Furnace in Lake Elsinore. Systems temperature split is 38 degrees. Combustion blower is amping under max spec. Flame sensor was cleaned and Reinstalled. Unit is equipped with a germicidal light which is still glowing strong at this time. Merv 16 filter is dirty for only being 4 months old. Ignitor is reading high but still in range at this time. Blower wheel is spinning freely. Performed A/C maintenance on a Lennox XC25. Condenser coils were heavily caked with dirt. System was chemically washed and rinsed. Cooling temperature split is right at 20 degrees. Systems control and defrost board are clear of any visual burn marks. Compressor is amping within range. Fan motor is amping under the max for this unit.

Tech arrived on site and started ac tune up. Checked attic and ducting. Ducts are standard r4 ducts. Furnace is clean. Motor amps are good. Static and airflow are good. Went to condenser and cleaned coils. Checked start components and amperages. They are good at this time. Charge is good. Installed float switch inside of primary line. Unit is operational upon departure.

Arrived on site to perform combo maintenance on 2004 system. Cycled system for heat. Checked indoor unit electrical and system components. Temperature rise across heat exchanger is slightly above the range. System is slacking on return air flow which is what could be causing the higher temperature. Cleaned blower assembly as well as heating compartment. Blower wheel is slightly dirty. Pulled evap coil cover to examine heat exchanger and check coil. Safety inspected heat exchanger. Heat exchanger passes safety inspection for today, but system is older and is getting slightly hotter than it should. Evap coil is very dirty, and is not only causing an air flow restriction but also poor air quality inside the home. Replaced 1 inch filter. Cycled system for cooling. Checked outdoor unit electrical and system components. Primary and secondary motor control have been recently replaced and are still within range and in good condition. Amp draws for compressor are very close to going over allow

Performed AC diagnostic on 2012 XC 21 Lennox condenser. Upon my diagnostic client stated the outdoor unit was not turning on and hot air was blowing out of supply vents. Upon further investigation found that the fuse had a hole blown through the bottom on it. Proceeded to also find that the duel secondary motor control was reading at 39 µF which is way below the specified reading of 45. High voltage relay also showed signs of pending on contact points which can lead to failure on start up if this increases and gets worse. Power disconnect was also not equipped with search protection in the case of a power outage thunderstorm etc. this may also cause the fuse to become blown. Upon inspecting the indoor unit I found the 5 inch thick Merv 16 filter was Has been in place since 2016. Filter was beyond restricted and clogged with dirt. This is choking the system off and reducing the efficiency heavily. Outdoor condenser coil’s are also covered in dog hair which is cutting systems Airflow

Replace existing system with listed equipment. Seal return platform and sheet metal top. Add balancing dampeners for balance. Seal all supply cans and install high flow registers.

Technician arrived on site and started performing one AC tune up. Cleaned condenser coil‘s with chemical and hose them down until no chemicals are present. Opened up electrical compartment and started to clean out cabinet. Found the capacitor to be reading week. Found compressor starting amps to be high. Fan motor is looking okay. No major oil leakage. Amps are within range but high. Charge is okay. Temp split is 17.9/20 Unit is old, and compressor is starting up rough. Recommend hard start kit to lower amperage. Would also recommend budgeting for replacement of system soon. Replaced cap. 1 year parts labor on that part.

Arrived on site to perform combo tune up on a 2019 Lennox unit. Condenser located in pack phased and Durand evaporator coil located in attic. Client stated no issues just wanted service and checked up on filter. Washed condenser inside and out. Unit really dirty cause of area and dogs. Primary and secondary controls are good. Amps draws on units are both good on compressor and fan motor. System pressure are good and cooling home good. No protection on unit. Cycled system. Inspected furnace and found filter extremely dirty due to area in home. Blower assembly is good. Motor is good and amp draws are in range. Evaporator coil was good at This time. drain lines are good. temperature rise and split were both good and in range. Recommend adding a phenomenal air to unit to improve air quality in home and in system as wide dose have allergies as she is home most of the time. No protection on unit recommend adding surge protectors to unit to protect from electrical surges and power outages th

Performed diagnostic on Attic fan. Client stated they just a couple days when it was warmer attic fan had turned on with a loud clanking noise and was concerned that something may have been wrong with it. Found attic Was working properly and tested. Motor ran smoothly and no noise. The loud noise could have been due to its sitting for a while and randomly coming on recently. Ultimately nothing seemed out of the ordinary or deficient. Also need to reschedule maintenance for air-conditioning do to it raining at the moment. Upon departure System is operational

Performed diagnostic on 3 year old Lennox heat pump system. System is not heating. They had another company come out twice to fix it and it worked for a bit but is down again. Cycled system for heat. Indoor kicks on and starts heating. Outdoor unit is not responding or kicking on. Checked for power, system has proper high voltage and low voltage command, contactor is not engaging. System is on low pressure lockout, system is low on refrigerant. Amber stated that she believes previous company did add refrigerant. Tried calling owner for options but could not get a hold of him. Left message, Amber can not make any decision. Will need to wait till owner calls in. No other work performed. Spoke to Larry the owner over the phone. He will be holding off on any repairs form now. He is fully aware of the full findings of the system. He advised that the office stated they will be billing him for the diagnostic. System is not operational upon departure.

Tech arrived on site. Started doing ac tune up. Fired up condenser and checked motor amperages. LRA was a little high. Cap was out of range. All other amperages are within range. Charge is good. Cleaned coils with chemicals and cleaned out the electrical compartment.

Post job. Picked up check for 3210

Tested both heating and cooling systems. Measured voltages, amp draws and temperatures. Inspected all electrical components. Cleaned flame sensor and tested ignitor. Tested all capacitors and inspected the fan motor. Cleaned burner assembly and cabinet. Washed outdoor condenser coil and verified refrigerant charge.

Arrived on site to perform combo tune up on a 2016 Lennox system. Furnace located in attic and condenser coil is located in back yard. Client stated no issues and was just wanting service done on system. Cycled cooling on and found condenser coil clogged and extremely dirty and restricted airflow. Washed condenser condenser coil inside and out. Recommend staying on maintenance to keep getting System cleaned. Checked electrical compartment. Primary was good. Secondary was good and in range. Checked amp drawls on unit and are in range. Would recommend adding a compressor booster kit to help prevent hard start ups and prolong system life. Fan motor is pulling max amps due to restrictions of condenser coil and is working hard. System pressure are stable and in range and system cooling home at 22 degrees. Cycled system. Cycled heater on and was good. Filter was extremely dirty. Recommend replacing filter. Lower assembly is dirty as she was advised last time out. Motor is good. Amp drawls

Performed routine fall maintenance on Lennox furnace in lake Elsinore. Due to extensive repairs needed on furnace from 1998. Would not recommend putting much repairs into it. Rather look into long term replacement options.

Performed furnace maintenance on 2014 Goodman Heater

Performed furnace maintenance on 2009 Bryant heater. Upon my maintenance I found multiple points of concerns that could lead to failure on AC/heating mode. 1. Found an indoor blower motor is beginning to over amp and has also ruptured it’s lubricant seal around the bearing this can lead to the motor overheating or locking up due to lack of lubrication 2. Single secondary motor control is become week due to motor using more power than needed if left in this condition battery can completely die and motor will not start 3. Flame sensor was heavily oxidizing and corroded 4. System was not equipped with surge protection in the case of power outages in thunderstorms etc. 5. Circuitboard had a slight burn marks three amp fuses already been replaced prior 6. Temp rise was it 61° considering that the allowable range is 60 this can be concerning and can potentially cause the heat exchanger to crack. Discussed full condition With homeowner and she is aware and will consider the repairs need

Total job is 15400. Balance due after Instal will be $400. Customer will pay us $400 when he gets his Lennox rebate

Arrived on site to perform furnace maintenance on 17 year old package unit. Cycled system for heat. Verified proper heating sequence of operations. Temperature rise across heat exchanger is within range. Ran system through 20 point inspection checklist. Blower wheel is dirty. Indoor motor is starting to leak oil. Secondary motor control is in range. Evap coil is dirty as well. Removed panel and opened up unit top to inspect heat exchanger. Heat exchanger does have some hot spots in certain areas. No visible cracks at this time. System is very old and inefficient. Homeowner mentioned that his bills in the summer time sometime jump from 200 to 600 dollars because of the AC running. Went over findings and recommendations with homeowner. Went over the cost of repair and ownership to keep current system operating. Homeowner ultimately does not want to repair the system or put any more money into it. He would like some replacement options for a new unit. Turning call over to Darren who will

Installation of a Single Stage Lennox FAU Financing options at $38/mo 6.99% 120 mo

Performed cleanings and install flame sensor along with surge protector

Arrived on site to return for service on a torn plenum. Client is aware this is a this repair today would be patching up Return prone to furnace as client is just trying to get more time out of system. Over found plenum did not have any support and was causing to off balance the plenum and where it was sealed tore. Advice it be best to add support by strapping duct strap under plenum and support it and not trip due to weight from um and ducting connected to it. Re sealed plenum with U.v and metal tape. Strapped up plenum with 2 straps crossing under plenum for support. System was now operational. client Did approved for repairs done today and is happy and is aware of reseal repairs. System is operational upon departure. Client will call us about other repairs and Gwen he would like to move forward with them.

Arrived on site to perform fall tune up on a 2018 carrier system. Furnace and evaporator coil located in attic. Client stated no issues. As system and home where built 2 years ago and just moved in. Cycled thermostat and was good. Found filter dirty and client was gunna supply his own and replace. Found black flex ducting used okay condition. Blower assembly and wheel slight dust accumulating. Motor is good and amp drawls are good. inducer motor is good and amp drawls are in range. Heat exchanger good. Evaporator coil good. Drain lines are good. Flame sensor is showing some wear and discoloration of oxidization at this time. Found temperature rise to be at 61 degrees and heating and is above rated range on system. Air flow restrictions could cause system to heat up high as not enough air flow is entering system. Found voltage at 121.3 and system is Rated at 115v. No protection on either unit. Recommend adding surge protectors to prevent system getting damaged from electrical surges an

Arrived on site to perform fall tune up a 2013 carrier system. Furnace furnace located in attic client stated no issues. Cycled nest thermostat and was good and operational. Found filters dirty and client was goin got go buy and supply his own. Found black flex ducting used and visually inspected system and found a big tear where the plenum meets the furnace is torn and leaking dirt into system bypassing the filter. Recommend resealing return plenum to stop dirt from entering from the attic. Blower assembly and wheel is dirty creating stress and wear on motor. Motor has slight oil developing from over Working and stress allowing dirty to accumulating with the oil. Would recommend replacing blower motor to extend system life span as it starting to show Signs of premature failure and if fails airflow will not be produced in heating and cooling. Secondary motor is good and in range. Inspect Heat exchanger and found heat impingement and is good at this time. Inducer motor is amping at 1.0

Inspected thermostat fault codes. Replaced restricted filter. Tested furnace multiple times for proper operation. Checked the vent cap on the roof. Temp rise at 36 degrees.