Lake Elsinore, CA

Upon arrival performed maintenance on heating system. Indoor motor and wheel are in bad condition. Motor is leaking oil and has play on shaft. Secondary motor control is out of range. Circuit board and electrical connections good. Flame sensor has oxidation build up. Dusted off electrical connections. Ducting is in good condition. Thermostat in working order. System is operational upon departure.

Upon arrival performed maintenance on heating system. Indoor motor and wheel are in bad condition. Motor is leaking oil and has play on shaft. Secondary motor control is out of range. Circuit board and electrical connections good. Flame sensor has oxidation build up. Dusted off electrical connections. Ducting is in good condition. Thermostat in working order. System is operational upon departure.

Electrical Protection Install- Upon arrival system is working and operational. I started at the outdoor unit by installing directly at the disconnect box. I then proceeded to the indoor unit, installed and mounted directly to the unit. Upon departure new surge protection units are installed and operational, system is working and operational upon departure.

Upon arrival, installed fan motor. Cleaned blower housing. Tested system. Unit is operational upon departure.

Arrived on site to perform tune up on a 8 year old Goodman unit. Client stated no issues and heating good. Filter were bit dirty and advised they should be replaced. They stated they would buy some to keep on hand. Blower assembly dirty and recommended cleaning wheel to prevent more stress on blower motor. Motor is okay at this time. Secondary motor control is out of range from over working motor. Recommend replacing before completely fails. All safety switches are operational. Temperature rise is good Drain lines are bit dusty but clear. No protection on unit and recommended adding protection as unit is getting older and at risk. As unit has zoning and 2 thermostat. Cycled unit and went over all findings and recommendations and repairs needed. Client is aware of how unit is working and it’s condition. Client did want to go forward with replacing the secondary control. Replaced and unit is operational after install. Client is aware and happy with today’s visit. Cycled unit and is

Upon arrival client said fan motor was not operational. Testing found it would come on and amp at max. Determined the motor is bad. Advised client of condition of heater and we should check heat exchanger for damage. Client declined and went forward with repairs. Had to rewire so,e of the old wires as things had been bypassed. Tested heating operation. Unit is operational upon departure.

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance in the attic by performing a duct leakage inspection. I then proceeded to the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been changed at this time, cool air provided. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of both units I found there to be no form of electrical protection on either, recommend adding surge protection to both units to protect the sensitive electrical components contained within the system. Priscilla would like to move forward with the surge

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance in the attic by performing a duct leakage inspection. I then proceeded to the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been checked, does need to be changed, home owner said they would pick some up and replace themselves. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of the indoor furnace unit I found there to be no form of condensate safety, recommend having a safety switch added to prevent possible flood damage. Upon departure system is working and operationa

Upon arrival system was operational. No failures or error codes. Client said it was giving off 3 flashes. Which would be a pressure switch issue. Cycled power and watch it go. No issues found. Temp rise and static are okay. Client provided further information of past issues which led to the conclusion the control board is having intermittent issues. Client will attempt the repair himself. Unit is operational upon departure.

Upon arrival found 1 18 year old Lennox system. Testing found the gas valve was not getting enough power from the board. The control board has failed. It is also possible that the gas valve has also failed but cannot test it unit board is replaced. Noted several other safety concerns. -gas line -poor flood protection. - furnace sitting on wood. Went over recommendations with the client. Client declined all repairs. Unit is not operational upon departure.

Upon arrival found the system not operational. Flames would lite but would not stay on. Testing found the flame sensor had failed. Also the blower motor is leaking a lot of oil. Replaced the flame sensor but need to order the motor because of its brackets. Unit is operational upon departure.

Set gas valve to “on” position and tested heat. Measured supply temps and monitored operation. System is working properly.

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance at the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been checked, does not need to be changed at this time. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of the indoor unit I found there to be no condensate safety as well as I found there to be no sediment trap. Recommend adding a safety switch to prevent flood damage and a gas repipe to add a sediment trap to be prevent debris from reaching the burners. Upon departure system is working and operational.

Upon arrival performed maintenance on 2007 heating units. Blower wheels are beginning to accumulate dust levels on blower. Secondary motor controls are in range. Circuit board and electrical connections good. Thermostat in working order. Client will replace his filters. Ampergess in system are lower the then manufacture specs. Ducting is in good condition. Ducts are strapped and connected. Gas valves in working order. No drips on gas piping. System is operational upon departure.

Upon arrival performed maintenance on 2007 heating units. Blower wheels are beginning to accumulate dust levels on blower. Secondary motor controls are in range. Circuit board and electrical connections good. Thermostat in working order. Client will replace his filters. Ampergess in system are lower the then manufacture specs. Ducting is in good condition. Ducts are strapped and connected. Gas valves in working order. No drips on gas piping. System is operational upon departure.

Upon arrival performed maintenance on 2007 heating units. Blower wheels are beginning to accumulate dust levels on blower. Secondary motor controls are in range. Circuit board and electrical connections good. Thermostat in working order. Client will replace his filters. Ampergess in system are lower the then manufacture specs. Ducting is in good condition. Ducts are strapped and connected. Gas valves in working order. No drips on gas piping. System is operational upon departure.

Upon arrival performed maintenance on 2007 heating units. Blower wheels are beginning to accumulate dust levels on blower. Secondary motor controls are in range. Circuit board and electrical connections good. Thermostat in working order. Client will replace his filters. Ampergess in system are lower the then manufacture specs. Ducting is in good condition. Ducts are strapped and connected. Gas valves in working order. No drips on gas piping. System is operational upon departure.

Turned system on, system is operational. Cycled system on and off multiple times and fired up with no issues. Client does have a dirty filter, do not have that size in van will order and wants maintenance done soon.

Turned system on, system is operational. Cycled system on and off multiple times and fired up with no issues. Client does have a dirty filter, do not have that size in van will order and wants maintenance done soon.

Turned system on, system is operational. Cycled system on and off multiple times and fired up with no issues. Client does have a dirty filter, do not have that size in van will order and wants maintenance done soon.

Turned system on, system is operational. Cycled system on and off multiple times and fired up with no issues. Client does have a dirty filter, do not have that size in van will order and wants maintenance done soon.

20 Point Inspection: Clean and Adjust Burners Check Combustion Air for Proper Venting Examine the Heat Exchanger for Damage / Corrosion Test Furnace Safety Controls Inspect Gas Piping Tighten Electrical Connections Measure the Voltage and Amperage Flush the Condensate Drains Measure Tempurature Difference between Supply and Return Air Vacuum Furnace Return Grille Adjust Gas Pressure & Pilot Clean in-place Blower Compartment Inspect Blower Wheel for Proper Balance Check the System's Static Pressures to Ensure Proper Airflow Inspect Duct Connections for Air Leaks / Sizing / Insulation Monitor Air Purification System Check all System Safety and Limit Switches Clean Flame Sensor Inspect Carbon Monoxide Detectors Check Thermostat for Proper Operation / Calibration

Performed diagnostic on system. Not heating. Cycled system for heat. Went into attic, found limit switch tripped. Filters are completely hammered, which is causing a restriction and caused limit switch trip. Reset limit. Changed out filters with approval. Cycled system for heat. Verified proper heating sequence of operations. System is operational upon departure.

Found gas valve to be not opening on call for heat, system goes through cycle, get proper voltage to gas valve just no gas. Client is gonna call builder of home. Before she does anything.

Found gas valve to be not opening on call for heat, system goes through cycle, get proper voltage to gas valve just no gas. Client is gonna call builder of home. Before she does anything.