Lake Elsinore, CA

Found gas valve to be not opening on call for heat, system goes through cycle, get proper voltage to gas valve just no gas. Client is gonna call builder of home. Before she does anything.

Found gas valve to be not opening on call for heat, system goes through cycle, get proper voltage to gas valve just no gas. Client is gonna call builder of home. Before she does anything.

Performed furnace Diagnostic on 2017 carrier heater. Upon arrival Annette stated that sister has been working intermittently and noticed that sometimes it works and then a couple hours later it won’t. Found that the furnace was in limit lock out. Reset system and furnace fired up at this time. Client mentioned that she had three supply vents are closed And then advised that the supply vent should be opened up to reduce overheating. Verify that filters are also in a good state. Flame sensor was slightly oxidized. Temperature rise was 58° coming very close to the 60° Max temperature rise. At this time client plans on selling the house in less than a year And would like to hold off on any repairs and maintenance plan at this time. Heater was reset and tested approximately six times and fired up properly at this time and reach desired temperature on the thermostat. Upon departure Heater is fully operational and heating

Upon arrival found 2 HVAC systems. The downstairs system was not operational at the thermostat. Went up into the attic and inspected the heater. Bypassed thermostat and the unit came on. Installed new thermostat and unit is operational now. Cycled in heat and cooling mode. unit is operational upon departure.

Performed fall maintenance on a 2019 lennox gas furnace. Customer reports error code 532 on the thermostat but good functioning heater so far this year. Systems heating temperature split is high but in range. Combustion blower and primary blower are amping in range. Filter is ok at this time. Sensors and switches were cleaned and tested. Gas valve and ignitor were tested and recorded. Duct runs are sealed. Zoning system was tested. Fixed the zoning board wiring issue which cleared the error code. System is not protected. Condition was discussed with homeowner. System is operational.

Performed furnace maintenance on 25 year old Lennox system. Cycled System for heat. Verified proper heating sequence of operations. Temperature rise across heat exchanger is basically at max allowed temperature from manufacture. Unit is operating on an extremely undersized return. Ran system through 20 point inspection checklist. Homeowner just replaced filter this morning. Unit is older and outside of its life expectancy, definitely would recommend getting heat exchanger properly examined. After speaking to both mother and daughter for permission to check heat exchanger and why it would be important to do so, Mary decided that she does not want it safety inspected on today’s visit. She is aware of the concerns that could be associated with a damaged heat exchanger. Went over other findings and recommendations. Wants to hold off on any work for today. Cycled system, system is operational upon departure.

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenanc on the roof at the package unit. I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been checked and does need to be changed, homeowner said he will pick some filters up. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Home owner currently has fire detectors down due to fresh paint, reminded to put back up soon for safety. Upon inspection of the package unit I found there to be no form of electrical protection on the unit, recommend adding a surge protector to protect the sensitive components contained

Upon arrival performed diagnostic. Found system to be operational . Tested secondary motor controls everything is in range. System was in a delay, possibly disconnect could’ve not been all the way intact. System is operating with amperages in range. Dirty filters, and dirty blower wheel. Outdoor coils were dirty gave system a wash. Advised client system needs a Maintenance. Will speak to husband when getting home about memebership. System is operational upon departure.

Upon arrival performed diagnostic. Found system to be operational . Tested secondary motor controls everything is in range. System was in a delay, possibly disconnect could’ve not been all the way intact. System is operating with amperages in range. Dirty filters, and dirty blower wheel. Outdoor coils were dirty gave system a wash. Advised client system needs a Maintenance. Will speak to husband when getting home about memebership. System is operational upon departure.

Upon arrival performed diagnostic. Found system to be operational . Tested secondary motor controls everything is in range. System was in a delay, possibly disconnect could’ve not been all the way intact. System is operating with amperages in range. Dirty filters, and dirty blower wheel. Outdoor coils were dirty gave system a wash. Advised client system needs a Maintenance. Will speak to husband when getting home about memebership. System is operational upon departure.

Upon arrival performed diagnostic. Found system to be operational . Tested secondary motor controls everything is in range. System was in a delay, possibly disconnect could’ve not been all the way intact. System is operating with amperages in range. Dirty filters, and dirty blower wheel. Outdoor coils were dirty gave system a wash. Advised client system needs a Maintenance. Will speak to husband when getting home about memebership. System is operational upon departure.

Arrived on site to perform fall tune up on 2011 Lennox unit. Client stated no issues. Furnace located in attic. Cycled and good. Filter are dirty and client will replace. Blower assembly has slight dust but okay. Motor is good and free of oil. Secondary motor control is good and in range. Inducer motor is good and inducer motor is good and in range. Flame sensors is good and in range. All other safety switches are operational. Unit creates clean blue flame. Tempe rise is good and heating home good. Drain lines are clear but would recommend adding a safety over flow switch to drain line to prevent over flow in attic. Found unit to be zoned and unit is not equipped with protection and would highly recommend adding su w protection to system to protect from electrical surge and power outages that can damage or even short out systems and components. Due to filter condition recommended adding a merv rack to keep more dirt out of unit or consider do a cleaning and purifying that will help kee

Tech arrived on site. Found 1 carrier slim door furnace. 10 years old. Started up heater and checked for proper ignition. Exhaust vent has more bend in it than it needs. It is effecting the exhaust motor. Would recommend a correction. Flame sensor is getting older and is oxidized. Cleaned it. Blower motor and exhaust motors are amping high. Airflow is good in the house. Temp rise is within range. Hot surface igniter is good. Heat exchanger has hot spots. No cracks at this time. Blower compartment was dirty. Recommend upgrading to better filtration.

Performed diagnostic on 4 year old Carrier system. Homeowners dog chewed up condenser wires. System was running fine before hand. Removed chewed up wires as well as chewed up black tubing. Spliced new wire and replaced tubing. No fuses were blow. Cycled system. System kicked on normally and started cooling. Went over electrical components to ensure nothing else was damaged. Went over maintenance program. Cycled system, system is operational upon departure.

Tech arrived on site, started furnace tune up. Unit was dirtier than last visit. Inside the blower compartment had dirt built up. Blower wheel as well. Inducer motor is almost amping at max. Cleaned unit, and tested heating operation. Heat rise was good. Airflow is good. Ducts are intact. Unit should be retrofitted with higher filtration to prevent future system failures. Unit is operational upon departure.

Performed heating maintenance on a 2018 carrier furnace. System is heating 56 degrees. Flame sensor was overheated, recommending replacement. Combustion blower is amping high. Primary blower is clean and spinning free. Ignitor was measured. Sensors and switches were cleaned and tested. System is not protected. I briefed the homeowner of the condition. System is operational.

Preformed furnace maintenance on 2007 Lennox heater

Performed combo maintenance on a Lennox system. Heating controls were measured and verified in range. Sensors and switches were tested snd cleaned. Duct runs are sealed. Filter was ok. Heating temperature split is range. Outdoor controls and components were tested and recorded. Refrigerant levels are ok. System was operational at end of appointment.

Returned to perform repairs. Correctly re-wired furnace ignition board and control board. Cycled system for heat. Verified proper heating sequence of operations. System is operational upon departure.

Tech arrived on site, furnace was extremely dirty inside. Cleaned out blower compartment and electrical. Ignition system is 18 years old. Return is undersized. Unit is not getting enough airflow. Filtration is poor. Blower motor is leaking oil. Made recommendations on how to improve the system. Talked about replacement. Unit is operational upon departure.

Quality control check

Performed furnace maintenance on a Lennox heater. Systems heating temperature split is 70 degrees. Filter is dirty and was replaced today. Sensors and switches were cleaned and tested for correct operation. Blower wheel is slightly dirty. Amp draws are in range. Ignitor is measuring in range. Electronic damping system is functioning well. At some point the safety switch was removed, recommending installing a new on. System is operational at end of appointment.

Performed AC/furnace maintenance on 2020 Lennox systems. Perform safety inspection on heater. temperature rise are is at proper level. 5 inch Merv 11 filter is heavily plugged up in restricted recommend this is swapped out immediately client says that they are ordering one off of the Internet. Performed AC maintenance. Clean the condenser coil due to high amounts of debris building up. This needs to be done once a year just before the summer to ensure proper efficiency and maintain warranties on Lennox unit. Refrigerant levels are in range. Compressor and fan Are pulling the proper amperage. At this time system is in great condition and recommend to keep this unit at a standard Maintenance is done twice a year to get the longest life out of it. Client stated that his wife is working at the moment and when she gets home he will go over maintenance plan and it’s about a few days to think about. Left maintenance program brochure It will be following up soon. Upon departure System Is ful

Arrived on site to perform diagnostic. Homeowner just took back possession of home after it being a rental for a couple years. Heating is not operating. He had someone else come out and told him that there were wires that were cut inside the furnace. He does have his insurance company coming out on Monday to look into this issue as well as other issues in the home. Cycled system for heating. Unit is completely unresponsive. Went into attic to inspect unit. Opened up unit and found that several wires have been pulled off from circuit board as well as ignition board. Ignition board looks like it has been replaced and all the wires are a complete mess. Unit Is not recieving command from thermostat due to disconnected wires. Went over findings and recommendations with homeowner. He wants to hold off on any repairs until his insurance company comes out on Monday. Also wants to hold off on any maintenance work as the home is going to be for sale. Closed unit back up. Unit is not operational

Performed AC/heater maintenance on mini split five head Lennox unit. Upon arrival client stated the downstairs system on mini split A Who is not working to performance as stated by the tenant living below. Initially asked the tenant she stated the system has no problem right now. temperature split checked out properly with a 30° delta split on downstairs head. Cleaned up condenser coil and electrical compartment. Amperages are in range for compressor and fan. All filters were clean by client. system is cooling and heating properly at this time.