Lake Elsinore, CA

Upon arrival performed heating tune up. Cleaned flame sensor. Cleaned inside entire cabinet. Indoor blower wheel is extremely dirty, this can cause motor damage over time. Advised moving up in filtration will help system out extremely from letting dust inside. Client will speak over with kids for monthly special that is over today. Circuit board and electrical connections good. Gas valve in working order. Ducting good. Return plenum box is insulation board. System is operational upon completion.

Upon arrival performed heating tune up. Cleaned flame sensor. Cleaned inside entire cabinet. Indoor blower wheel is extremely dirty, this can cause motor damage over time. Advised moving up in filtration will help system out extremely from letting dust inside. Client will speak over with kids for monthly special that is over today. Circuit board and electrical connections good. Gas valve in working order. Ducting good. Return plenum box is insulation board. System is operational upon completion.

Upon arrival performed heating tune up. Cleaned flame sensor. Cleaned inside entire cabinet. Indoor blower wheel is extremely dirty, this can cause motor damage over time. Advised moving up in filtration will help system out extremely from letting dust inside. Client will speak over with kids for monthly special that is over today. Circuit board and electrical connections good. Gas valve in working order. Ducting good. Return plenum box is insulation board. System is operational upon completion.

Upon arrival performed heating tune up. Cleaned flame sensor. Cleaned inside entire cabinet. Indoor blower wheel is extremely dirty, this can cause motor damage over time. Advised moving up in filtration will help system out extremely from letting dust inside. Client will speak over with kids for monthly special that is over today. Circuit board and electrical connections good. Gas valve in working order. Ducting good. Return plenum box is insulation board. System is operational upon completion.

Arrived on site to perform spring tune up on a 16 year old unit. Condenser located on side of yard. Cycled unit and operational. Found disconnect to be very loose and be a hazard since power is live. Recommend replacing. Washed condenser coil inside and out and unit was very dirty. Found starter to have putting burnt up. Secondary motor control was good as it was replaced recently. Fan motor is over amping and can fail here at any time. Checked compressor start up and run amps and found them to be at a high rate. Advised is not good and can get worse as it get hotter outside. No pro on unit. Found r-22 refrigerant used and unit is hold charge steady and cooling hole at 23 degrees. Filter was replaced. Blower assembly has a lot of dirt build up from past years. Motor has build up from leaking oil and dirt entering unit. No protection on u it and recommend so to protect older units. Cycled unit and went over all findings and how unit is run in and areas of concerns. As well as recommend

Adjusted the fan blower speed for the second stage cooling to medium-high from high. Jumped system to second stage and client confirmed the sound is much better.

Performed 2 system maintenance on 18 y/o furnace. Checked electrical components. Measured temperature split. Capacitors were weak and need to be replaced. Indoor blower housing is dusty and could benefit from being cleaned. Filters need to be replaced , customer is aware and will change them out. Heat exchangers we’re checked. Both systems were operational upon departure.

Performed AC maintenance on a 2002 weather king. Customer reports no use of cooling mode this season. Indoor blower is amping high and significantly leaking oil. This can lead to elevated electric costs and the interruption of operation. The cooling temperature split is low at 10 degrees. Outdoor unit was chemically cleaned. Refrigerant levels were found to be low of R22. Battery cap is in range. Start amps for the compressor are over max for this unit. Run amps are also fairly high. This is normal for a system of this age but these things should be addressed. High voltage switch is heavily burned up. Condition was discussed with homeowner. He has intentions to replace within a few years however today he does want to address a few parts at this time. System is operational.

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance in the attic by performing a duct leakage inspection. I then proceeded to the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been changed. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of the indoor furnace unit I found there to be no form of electrical protection or condensate safety, recommend having surge protection added to both units to protect the sensitive electrical components, and a condensate safety added to prevent potential flood damage. Upon departure sy

Performed AC maintenance on a 2020 Lennox XC20. Cooling temperature split is 23 degrees, filter is clean at this time. UV system protection is ok. Indoor amp draws are in range. Condensate lines are clear. Duct runs are sealed. Outdoor unit was chemically cleaned. Outdoor amp draws are ok. Refrigerant levels weee verified in range. Outdoor electrical protection was installed today. System is operational.

Performed maintenance on a Guardian gas furnace in Lake Elsinore. Customer reports frequent use of the furnace this season. Filter is dirty. Heating temperature split is in range. Sensors and switches were cleaned and tested. Gas valve and ignitor were tested. Primary and combustion blower are in good health. Condition was discussed with homeowner, system is operational.

Heat Load Calculations will be finalized by 2/23, any adjustments necessary will be at no cost - Installation of Slim Line 19 SEER Variable Speed A/C with Full Variable Speed Heater.

Performed furnace maintenance on a 2012 Goodman gas furnace in lake Elsinore. Customer reports light use of the heating system. Customer provided filter for change today. System is heating high with a 62 degree split. Gas pressure was adjusted to help bring the heat back within spec. Sensors and switches were tested and cleaned. Gas valve and ignitor were tested. Condensate lines are clear. Evaporator coil does not have a drain pan. System is operational.

Upon arrival, client said she had We Care do a furnace tune up and they condemned her heat exchanger. Got additional quotes from fel air. Pulled heat exchanger and confirmed it was cracked. Went over repair/replacement options. Client is open to explore new system options.

Arrived on site. Performed heating tune up on 3 year old Goodman furnace. All components are good. Found return duct to be undersized. Causing high static pressure and high temperature rise. System was Almost over heating. Recommend adding additional return or upsize existing return. Informed client. System is operational upon departure.

Arrived on site to perform fall tun rip on a 1993 lennox unit. Cliystated no issues and heats up good. Client has just replaced Ac and barley uses heater. Cycled unit at thermostat and found original thermostat to have issues with the Temperature button as it need a lot of force to move temperature advised could be just getting old. Filter was okay. Blower assembly is dirty from dirt entering unit. Inducer motor is operational both motors just have high amps draws. Spark igniter. Flame sealed oxidizes but okay at this time just old. Unit is on wood block and not furnace stands. Just old design of unit. Drain lines are okay and clear. Advised no protection unit n unit and recommended adding some. Puns black flex ducting undersized on the return as he did not replaced ducting. Advised client now is the time to consider full system replacement due to the age and inefficiency of unit and repairs and recommendations that could occurr in future compared to full system replacement. Cycled un

Performed AC Maintenance ON A 2015 Goodman AC cooling temperature split in range. Indoor components measured outdoor unit cleaned compressor bay and service panel cleaned battery cap is put of range at this time.this can cause irreversible damage to the major components if ignore for too long. Refrigerant levels were checked. Condition was discussed with the homeowner. Unit operational upon departure.

Collected $1000 deposit. Balance due is 7523

Upon arrival performed heating tune up on 2 heating systems. Advised client did not have that many 20x20 filters. Client replaced filters. Dusted off return grills. Blower wheels are dirty and need cleaning. Ampergess throughout system in rNge. Secondary motor control is almost out of range. On bigger unit found heat exchangers cracked/ damaged. Advised client of issue that is happening upstairs, advised due to liability reasons have to shut the gas off until unit is fixed or replaced. Client advised they don’t have funds to purchase a new system, just purchased Air conditioning. Put system back together, shut gas valve off. Client is Gonna speak to husband when gets home from work. Systems are operational for heating without gas shut off. Client is fully Aware.

Upon arrival performed heating tune up on 2 heating systems. Advised client did not have that many 20x20 filters. Client replaced filters. Dusted off return grills. Blower wheels are dirty and need cleaning. Ampergess throughout system in rNge. Secondary motor control is almost out of range. On bigger unit found heat exchangers cracked/ damaged. Advised client of issue that is happening upstairs, advised due to liability reasons have to shut the gas off until unit is fixed or replaced. Client advised they don’t have funds to purchase a new system, just purchased Air conditioning. Put system back together, shut gas valve off. Client is Gonna speak to husband when gets home from work. Systems are operational for heating without gas shut off. Client is fully Aware.

Upon arrival performed heating tune up on 2 heating systems. Advised client did not have that many 20x20 filters. Client replaced filters. Dusted off return grills. Blower wheels are dirty and need cleaning. Ampergess throughout system in rNge. Secondary motor control is almost out of range. On bigger unit found heat exchangers cracked/ damaged. Advised client of issue that is happening upstairs, advised due to liability reasons have to shut the gas off until unit is fixed or replaced. Client advised they don’t have funds to purchase a new system, just purchased Air conditioning. Put system back together, shut gas valve off. Client is Gonna speak to husband when gets home from work. Systems are operational for heating without gas shut off. Client is fully Aware.

Upon arrival performed heating tune up on 2 heating systems. Advised client did not have that many 20x20 filters. Client replaced filters. Dusted off return grills. Blower wheels are dirty and need cleaning. Ampergess throughout system in rNge. Secondary motor control is almost out of range. On bigger unit found heat exchangers cracked/ damaged. Advised client of issue that is happening upstairs, advised due to liability reasons have to shut the gas off until unit is fixed or replaced. Client advised they don’t have funds to purchase a new system, just purchased Air conditioning. Put system back together, shut gas valve off. Client is Gonna speak to husband when gets home from work. Systems are operational for heating without gas shut off. Client is fully Aware.

Arrived on site to perform maintenance on 1999 ComfortMaker furnace. Homeowner feels like his heater is inefficient and would like to get it looked At. Furnace is original to home. Cycled system for heating. Verified proper heating sequence of operations. Ran system through 20 point inspection checklist. Although system is heating, there is a number of concerns with unit which are as follows: 1. Temperature rise across heat exchanger is high and is above manufacture ratings. 2. Ductwork is undersized for the size of the unit and is creating high pressure inside the unit. 3. Amperage draw on inducer motor and indoor blower motor are high. Although they are still within range, it is higher than what we would like to see. 4. Indoor blower wheel is dirty, and causing the motor to overwork. 5. Indoor motor has leaked out a significant amount of oil. 6. Condensation drain lines do not have any condensation safety switches on drain lines. 7. Due to a high temperature rise and a high pres

Upon arrival performed maintenance on heating system. Indoor motor and wheel are in bad condition. Motor is leaking oil and has play on shaft. Secondary motor control is out of range. Circuit board and electrical connections good. Flame sensor has oxidation build up. Dusted off electrical connections. Ducting is in good condition. Thermostat in working order. System is operational upon departure.

Upon arrival performed maintenance on heating system. Indoor motor and wheel are in bad condition. Motor is leaking oil and has play on shaft. Secondary motor control is out of range. Circuit board and electrical connections good. Flame sensor has oxidation build up. Dusted off electrical connections. Ducting is in good condition. Thermostat in working order. System is operational upon departure.