Hemet, CA

Upon arrival Performed heat pump tune up. Indoor filter is dirty, UV light is out. Circuit board and electrical connections are good, but there is no protection on system. It started raining outside, client said to please not do outside doesn’t wanna damage system. Will do rest when replacement of lights and UV.

Upon arrival Performed heat pump tune up. Indoor filter is dirty, UV light is out. Circuit board and electrical connections are good, but there is no protection on system. It started raining outside, client said to please not do outside doesn’t wanna damage system. Will do rest when replacement of lights and UV.

Upon arrival, found unit none operational. Breaker was off. Found and tested the secondary motor controller. It had failed. Installed a temporary part to test system. Charge is okay. Might need slight adjustments. Both indoor and outdoor motor were looking bad but still operational. Compressor amperages is within range. Recommend doing preventively repairs on motors prior to summer.

Upon arrival performed diagnostic on motor. Client states outside kicks on but shuts off. System is really old and has a variable speed motor. Motor has about 6-7 different electrical splices. Replaced transformer, then found high limit to be bad. Got system up to run. Client decided he did not want to do any repairs, house is gonna be sold AS IS in 3 months. Client wanted to sign up with Memebrship cause he is moving out of that spot and wants to transfer over membership.

Upon arrival performed diagnostic on motor. Client states outside kicks on but shuts off. System is really old and has a variable speed motor. Motor has about 6-7 different electrical splices. Replaced transformer, then found high limit to be bad. Got system up to run. Client decided he did not want to do any repairs, house is gonna be sold AS IS in 3 months. Client wanted to sign up with Memebrship cause he is moving out of that spot and wants to transfer over membership.

Upon arrival performed diagnostic on motor. Client states outside kicks on but shuts off. System is really old and has a variable speed motor. Motor has about 6-7 different electrical splices. Replaced transformer, then found high limit to be bad. Got system up to run. Client decided he did not want to do any repairs, house is gonna be sold AS IS in 3 months. Client wanted to sign up with Memebrship cause he is moving out of that spot and wants to transfer over membership.

Upon arrival performed diagnostic on motor. Client states outside kicks on but shuts off. System is really old and has a variable speed motor. Motor has about 6-7 different electrical splices. Replaced transformer, then found high limit to be bad. Got system up to run. Client decided he did not want to do any repairs, house is gonna be sold AS IS in 3 months. Client wanted to sign up with Memebrship cause he is moving out of that spot and wants to transfer over membership.

Arrived on site to return to inspect heater on a 2020 carrier unit. Cli stated unit is locked up again. We were last out and unit tripped on high limit for dirty filters. Units stopped working later that day. Unit was tripped again. Inspected ducting, airflow, and temperature rise. Found all areas good and unit was operational. Inspected all safety switches. Found roll out switches was not flush on burner box. Found it tripped and rest. Cycled again and unit was operational and did not trip or have issue. Cycled couple time and unit was heating good for 30 mins and was cycled 3 times. Advised client of findings and he is aware of how unit is running. Colitis aware unit is operating and not heating up due to airflow or temperature rise. Unit is operational upon departure and happy we came to over view whole system. No charge today but if any issues occur again we can come out with a Dx fee. Client is aware and okay with so.

Upon arrival performed maintenance on heating system. Circuit board and electrical connections in range. Cleaned flame sensor. Dusted off electrical components. Filter is beginning to get dirty. Light is dimming and isn’t as bright. Client replaces his own filters. Safety switches are in range. Amperage’s throughout system are very good. Cleaned venting. Shut off valve in working order. System is operational upon departure.

Upon arrival performed maintenance on heating system. Circuit board and electrical connections in range. Cleaned flame sensor. Dusted off electrical components. Filter is beginning to get dirty. Light is dimming and isn’t as bright. Client replaces his own filters. Safety switches are in range. Amperage’s throughout system are very good. Cleaned venting. Shut off valve in working order. System is operational upon departure.

Upon arrival performed maintenance on heating system. Circuit board and electrical connections in range. Cleaned flame sensor. Dusted off electrical components. Filter is beginning to get dirty. Light is dimming and isn’t as bright. Client replaces his own filters. Safety switches are in range. Amperage’s throughout system are very good. Cleaned venting. Shut off valve in working order. System is operational upon departure.

Upon arrival performed maintenance on heating system. Circuit board and electrical connections in range. Cleaned flame sensor. Dusted off electrical components. Filter is beginning to get dirty. Light is dimming and isn’t as bright. Client replaces his own filters. Safety switches are in range. Amperage’s throughout system are very good. Cleaned venting. Shut off valve in working order. System is operational upon departure.

Arrived on site to diagnose not operating unit. Client stated unit is new as home built in 2020. Clutch stated fan dose not turn off. Found thermostat not working. Inspected electrical found unit locked up on high limit. Filters were dirty and client stated he would order new one. System is operational in heating and cooling. Client signed up on esa. System operational upon departure.

Upon arrival performed heating maintenance. Indoor blower wheel is beginning to get dirty, client is running Merv 8. Advised moving up to merv 16. Blower wheel beginning to get dirty. Circuit board and electrical connections in range. Thermostat in range. Dusted off electrical components. Tested system multiple times. Client does not have liquidity to do cleanings at the moment. Collected funds from 8/1/20.

Upon arrival performed heating maintenance. Indoor blower wheel is beginning to get dirty, client is running Merv 8. Advised moving up to merv 16. Blower wheel beginning to get dirty. Circuit board and electrical connections in range. Thermostat in range. Dusted off electrical components. Tested system multiple times. Client does not have liquidity to do cleanings at the moment. Collected funds from 8/1/20.

Upon arrival performed heating maintenance. Indoor blower wheel is beginning to get dirty, client is running Merv 8. Advised moving up to merv 16. Blower wheel beginning to get dirty. Circuit board and electrical connections in range. Thermostat in range. Dusted off electrical components. Tested system multiple times. Client does not have liquidity to do cleanings at the moment. Collected funds from 8/1/20.

Upon arrival performed heating maintenance. Indoor blower wheel is beginning to get dirty, client is running Merv 8. Advised moving up to merv 16. Blower wheel beginning to get dirty. Circuit board and electrical connections in range. Thermostat in range. Dusted off electrical components. Tested system multiple times. Client does not have liquidity to do cleanings at the moment. Collected funds from 8/1/20.

Upon arrival performed heating tune up on heat pump carrier. Client has moved into home less then a year. Went up into the attic to start my tune up, seen DATS sensor just hanging out of furnace plenum. Let client know as soon as I got up that sensor was out, client said he did have issues during cooling season with system. Warranty came out and fixed issues. ( left sensor out ). We have a 14 & 12 inch duct in supply ducting. System is a 4 ton. System is zoned so system is most likely having issues when running 1 zone. Static pressure goes above .7 and max system needs is .2. Went ahead and checked condenser outside washed it down. Disconnect on wall has very poor seal, water can possibly get trapped inside and cause water to touch electrical. Opened up condenser top and found sensor hanging and hiding behind wires. That sensor is connected to compressor crack case heater. Advised they must’ve taken off and accidentally broke clips. Fresh air machine inside of attic does not have duc

Upon arrival performed heating tune up on heat pump carrier. Client has moved into home less then a year. Went up into the attic to start my tune up, seen DATS sensor just hanging out of furnace plenum. Let client know as soon as I got up that sensor was out, client said he did have issues during cooling season with system. Warranty came out and fixed issues. ( left sensor out ). We have a 14 & 12 inch duct in supply ducting. System is a 4 ton. System is zoned so system is most likely having issues when running 1 zone. Static pressure goes above .7 and max system needs is .2. Went ahead and checked condenser outside washed it down. Disconnect on wall has very poor seal, water can possibly get trapped inside and cause water to touch electrical. Opened up condenser top and found sensor hanging and hiding behind wires. That sensor is connected to compressor crack case heater. Advised they must’ve taken off and accidentally broke clips. Fresh air machine inside of attic does not have duc

Upon arrival performed heating tune up on heat pump carrier. Client has moved into home less then a year. Went up into the attic to start my tune up, seen DATS sensor just hanging out of furnace plenum. Let client know as soon as I got up that sensor was out, client said he did have issues during cooling season with system. Warranty came out and fixed issues. ( left sensor out ). We have a 14 & 12 inch duct in supply ducting. System is a 4 ton. System is zoned so system is most likely having issues when running 1 zone. Static pressure goes above .7 and max system needs is .2. Went ahead and checked condenser outside washed it down. Disconnect on wall has very poor seal, water can possibly get trapped inside and cause water to touch electrical. Opened up condenser top and found sensor hanging and hiding behind wires. That sensor is connected to compressor crack case heater. Advised they must’ve taken off and accidentally broke clips. Fresh air machine inside of attic does not have duc

Upon arrival performed heating tune up on heat pump carrier. Client has moved into home less then a year. Went up into the attic to start my tune up, seen DATS sensor just hanging out of furnace plenum. Let client know as soon as I got up that sensor was out, client said he did have issues during cooling season with system. Warranty came out and fixed issues. ( left sensor out ). We have a 14 & 12 inch duct in supply ducting. System is a 4 ton. System is zoned so system is most likely having issues when running 1 zone. Static pressure goes above .7 and max system needs is .2. Went ahead and checked condenser outside washed it down. Disconnect on wall has very poor seal, water can possibly get trapped inside and cause water to touch electrical. Opened up condenser top and found sensor hanging and hiding behind wires. That sensor is connected to compressor crack case heater. Advised they must’ve taken off and accidentally broke clips. Fresh air machine inside of attic does not have duc

Arrived on site to perform fall tune up on a arcoaire unit in garage. Client stated unit is old but is good and heating. He also had a thermostat and in door motor put in. Filter is dirty and he would replace. Blower assembly and whee is dirty. Motor is new. Inducer motor is high on amps. Temperature rise high. Found unit with only one drain line and highly recommended adding a safety over flow switch. Gas line has no sediment trap. No protection on old unit and recommended adding surge protection that’s hard wired into line of power for unit to protect unit from electrical surges and power outage that can damage or even short out systems and components. Cycled unit and went over findings and areas of concerns with client as he is aware how unit is running and it’s condition. Client did declined recommendations for. I was he know unit is old but wants to hold off and see how long unit will get him as he uses Ac more then the heater. Client os aware of areas of concerns. Cycled unit

Arrived on site for odor emitting from underneath the sink connecting to condensation lines on Ac system. Upon arrival homeowner stated that she has had home warranty come out and they cannot cover smell issues. Began diagnostic underneath the sink and found very pungent odor present in this area. Proceeded to evaporator coil inside of addict and found signs of water drainage inside of emergency pan and also opened up evaporator coal and found tons of debris and dust buildup inside. Due to all the dust and debris that is built up over time once water mixes with it this can create an odor which is similar to dirty sock syndrome. Presented and informed all possible ways to Illuminate odor. Client is interested but needs time to think about it due to car engine issues at the moment that need to be Prioritized first. All the client would like to do something about it we will be signing her up on a Maintenance program to keep system at standard in both summer and winter. Client would like

Replaced inducer motor for a Coleman Downflow furnace. System was cycled and verified operational.

Upon arrival found system flat on refrigerant. Went over repair options. Due to age and cost of repair, client wants replacement options. Need to come back Tuesday to complete financing.