Hemet, CA

Performed service for a gas furnace blowing cold air. Found system not completing the startup process on a demand for heat. Combustion blower is currently not operational despite getting the necessary voltage. The control board is very burned up. This is concerning to any expectation of long term reliability. Discussed options and equipment maintenance plans with the customer. Ordered combustion blower and started scheduled maintenance with homeowner. System is not operational at end of appointment.

Upon arrival performed diagnostic on ac system. System on arrival was not operational. Secondary motor control was completely out of range. Replaced and got system up and going. Compressor start amps are very close to max LRA. Condenser fan motor running borderline max amps. Compressor is running extremely hard. Client just wanted to get least expensive fix, this is a rental property. No memebrship

Upon arrival performed diagnostic on ac system. System on arrival was not operational. Secondary motor control was completely out of range. Replaced and got system up and going. Compressor start amps are very close to max LRA. Condenser fan motor running borderline max amps. Compressor is running extremely hard. Client just wanted to get least expensive fix, this is a rental property. No memebrship

Upon arrival performed diagnostic on ac system. System on arrival was not operational. Secondary motor control was completely out of range. Replaced and got system up and going. Compressor start amps are very close to max LRA. Condenser fan motor running borderline max amps. Compressor is running extremely hard. Client just wanted to get least expensive fix, this is a rental property. No memebrship

Upon arrival performed diagnostic on ac system. System on arrival was not operational. Secondary motor control was completely out of range. Replaced and got system up and going. Compressor start amps are very close to max LRA. Condenser fan motor running borderline max amps. Compressor is running extremely hard. Client just wanted to get least expensive fix, this is a rental property. No memebrship

Performed diagnostic on a package unit in hemet. System is not heating. Customer reports unit to be original to the home around 40 years. Found transformer to be not sending voltage to the gas valve or thermocouple. Tested the AC to find the compressor is running on 23 amps which is well over spec. The homeowner is aware of the condition of the system. Customer has received quotes and wants to get a quote from us as well. Holding off on repairs. Scheduled equipment appointment for Monday 2-4.

Arrived on site to perform Ac tune up for first time out client on a 2007 Rheem package unit. Client stated unit has only been maintenance couple time in the 15 years of life. Client stated he has issues with airflow and feels it’s not cooling as good. Cycled unit and was cooling. Filter was replaced last month. Found new ducting and see that was replaced with the unit 15 years ago. But found unit to have a lot of ducting spliced in and 2 added vents into garage. Advised unit is not getting enough airflow to properly give supply airflow into each room properly. Found return to be undersized and not enough airflow as it can unit to over heating or not cool as properly. Blower assembly is dirty and has slight oil from motor working and airflow restriction as motor is now working hard and due to age. Secondary control was good and in range. Compressor start ups are good and run amps as well. Fan run amps are good as well. Evaporator coil was dusty but no major build up. Inspected retu

Performed furnace maintenance on 2018 Intertherm downflow heater. Upon arrival homeowner stated that they have been having issues with the heating up and it feels like it doesn’t get the temperature in time. Found that filter was heavily clogged up and causing a massive air restriction which will reduce heating time and efficiency severely. Filter was cleaned It should be checked every 1 to 3 months. Temperature rise within range along with all electrical components checking out properly. Indoor blower air mixing cabinet is becoming dirty due to 1 inch washable filter not being cleaned out enough which will cause issues if this continues to happen. System is not equipped with surge protection. Informed and explained the full condition of Omar’s 2018 heater. At this time Omar would not like to renew it needs to hold off for the time being and will give us a call once he’s ready. Upon departure heaters operational

Upon arrival, client said 2 bedrooms weren’t getting any airflow. Inspected system. Found the system to be poorly designed and installed. Ductwork is older. Found when previous owners added addition they disconnected the supply duct to rooms with no airflow. Attic is closed off by a firewall. Need to see if we can cut through fire wall to run new duct.

Arrived on site to perform fall tune up on a 2017 lennox system. Furnace located in attic. Client stated no issues. Unit is heating good. Filter was really dirty and replaced as they supplied. Blower assembly and wheel is dusty from dirt entering unit and lack of filter change out. Motor is good and free of oil. Amp draws are in range. Inducer motor is good and in range as well. All safety switches are operational. Drain lines are clear at this time. Tempe rise is good and heating home. Flame sensor and igniter are good and in range. Found no protection on unit. Recommend adding to protect systems from electrical surges and power outages that can damage or even short out systems and components. Cycled unit to ensure system operating. Went over all findings and and how system running and recommendations advised of. Client did hold off for now and will see what they would like to do and let us know. Emailed it over and system is operational upon departure.

Arrived on site to perform fall tune up on a 2003 Bryant unit located in garage. Client stated unit is older but still working good. No issues. Cycled heater and is operational. Filter dirty and replaced. Blower assembly and whee is dirty from lack of filter change out and dirt entering unit. Motor has slight oil leaking as it’s working hard pulling 5.7 and max rated for 6.8. Advised motor is working hard and could fail in future. Secondary motor control is out of range and weak as it could fail in future. Inducer motor is working hard but still not in range. Client stated they don’t use heater a lot unit is heating up at 56 degrees and is high. Client did declined getting heat exchanger inspected as they are just waiting for home insurance to replace and just let unit die out and they would replace with the insurance as they did replace the Ac already. Drain lines are dirty. Gas lines has no sediment traps. No protection on units and recommended adding to protect unit from electri

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance at the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been changed at this time, cool air provided. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of the indoor unit I found the blower housing to be heavily caked with dirt and dust, as well as I found there to be no condensate safety. Recommend having a blower housing pull and clean performed as well as having a condensate safety added to prevent possible flood damage. Upon departure system is working and operational

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance at the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been checked, does not need to be changed at this time. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of the indoor furnace unit I found the blower wheel and scroll wheel to be heavily impacted with dirt and debris, recommend having a blower housing pull and clean performed to alleviate premature wear on the blower motor. Upon departure system is working and operational.

Upon arrival, found Honeywell T4 thermostat locked out. Obtained user manual and found the code. Which was 1234. After unlocking the thermostat tested operation of heater. Heater shut off at the set point. Installed cool air solutions sticker for more efficiency. Unit is operational upon departure.

Upon arrival, client had already diagnosed system as having a bad pressure switch hose. Client removed damaged part. Previous tech gave and installed part for client. Just did the same. Unit has hot spots on control board. Cap is reading low but within range. Heat exchanger has hot spots. Flood protection is extremely poor on unit. Inducer motor is amping at max. Duct work on system is great. Unit is operational upon departure.

Upon arrival found the system to be operational. Client said the utility bills have gone up drastically. Outdoor temp Sensor was reading high. Bypassed the outdoor temp sensor. It now reads off of internet weather. Set thermostat to be locked out and only use off of the phone. Unit is operational upon departure. No notes or filter change out on last visit, unless it was customer supplied.

Upon arrival found 15 systems that needed to be inspected. Started on the smaller kids center building. Building had 7 package units. All installed in 1989. 4/7 units are not cooling. Units 5 and 7 have bad compressors and will need extensive repairs. Unit 6 is missing a leg of power from the breaker. Need an electrician to diagnose issues. Unit 3 has no heat, cooling operational. Units 1-2 need maintenance but are operational in both heating and cooling. All of these units need new filters and general cleaning. Moved to main building. All units installed in 2004. There are 6 units in total on this roof. 4 package units and 2 split systems. All units need new filters. 2 units are not cooling. Unit 8 has a bad compressor and unit 4 is low on refrigerant. Moved to office building. Found 1 split system. Install date is approximately 1988. Cooling is operational. Components are rusty. Heater is extremely dirty. Heat is intermittent. Needs a new flame sensor minimum to provide he

Upon arrival found system not operational. Unit would light but would shut off. Testing found the flame sensor was dirty. Cleaned flame sensor and its operational again.

System is operational upon? System error. Client thought opposite when setting temperature.

System is operational upon? System error. Client thought opposite when setting temperature.

System is operational upon? System error. Client thought opposite when setting temperature.

System is operational upon? System error. Client thought opposite when setting temperature.

Upon arrival found the unit was not operational. Error code was for the pressure switch. Cycled power and unit began to heat. Found burn marks on control module. Most likely an intermittent issue. Let unit run for a couple minutes and cycled it. Unit is operational upon departure.

Total payment amount is $20,346. Invoice amount is for $23,364 but the rebate will take it down to $20,346.

Upon arrival performed maintenance on Goodman system. Indoor blower wheel is very dirty and needs cleanings. Circuit board and electrical connections are ok. Gas valve in working order. Inducer draft motor running at max amps. Dusted and cleaned electrical connections. Client was stating that he added 2599 dollars worth of refrigerant outside. Did not fix leak cause last company was not able to. Advised that we have payments plans to get client into a fully warrantied system. With upgraded filtration that they were interested in. Madison to come out and give clients replacement options. System is operational upon departure.