Vista, CA

Performed heating and Ac tune up and installed Sensi predict kit

Sensi predict installation

Maintenance and Sensi Predict installation

Performed Ac maint on 2017 Lennox system. Cycled system for cooling. Checked indoor unit electrical and system components. Blower wheel is clean as well as evap coil. Amp draws are within range for indoor motor. Merv 16 filter is extremely dirty and should be replaced. System also had a 1 inch filter in return plenum that should be removed to prevent restriction. Homeowner stated they will be ordering Merv filter and replacing themselves, left Merv filter out of unit for time being system is running on the 1 inch filter which is to be removed when Merv filter is replaced. Checked outdoor unit electrical and components. Amp draws on compressor and fan motor are within range. Secondary motor control readings in range. Primary motor control Is in good shape. System could use a compressor hard start kit as it does not have one and it is a heat pump meaning compressor is used all year round. Pulled condenser motor to thoroughly wash out condenser coil as it was very dirty. Refrigerant level

Returned to Instal 12x6 grill in the kitchen, finalize completed lowes paperwork and find out why the ac wouldn’t turn on. Breaker had popped

Performed fau maintenance on 2 year old system. Cycled furnace for heat. Verified proper heating sequence of operations. Temperature rise across heat exchanger is within range. Blower wheel and evap coil are clean. Blower motor amp draws are within range and motor looks healthy. Tested heating components all are working accordingly. Verified safety components are working accordingly. Cleaned burner compartment. Merv 11 filter is dirty and should be replaced. Replaced filter with filter That was provided by homeowner. Wiped off return registers. Advised homeowner that she should upgrade filter to a Merv 16 for better filtration. Cycled system, system is fully operational upon departure.

We will be replacing the heater and leaving the ac unit. We will be replacing the supply and return plenums with a new digital thermostat. We will be replacing the supply registers and cutting in a return in the small room.

Arrived on site. Homeowner states that his girlfriend and himself have been feeling sick more than usual lately. He was in the hvac trade before, and he feels like he may need to get his coil cleaned. System is from 1988. Inspected evap coil and found it to be surprisingly clean. Drain pan is completely rusted out. Blower wheel is slightly dirty but is also very rusted out. Ductwork is in very poor shape. All seals are broken as it was only sealed with duct tape when it was installed. Refrigerant levels are low and system is only producing a 10 degree temperature split, which explains why there is so much rust on system. Went over findings and recommendations with homeowner. Stated He was only looking to get his coil cleaned and since it doesn’t need it then he’ll leave the system as is. System is operating in same fashion as prior to my arrival, no work performed.

Upon arrival performed maintenance. Indoor motor & wheel are in bad condition. Motor is leaking oil, bad bearing. Blower wheel is completely dirty. Plenum are in bad condition, very dirty. Heat exchanger has slot of heat marks, did not identify any breaches. Evap coil is clogged causing air restrictions. Return air is very undersized for system. Temp rise 57. No insulation in attic. System was reset tested and fully functional upon departure. Darren to come out and give options for replacement.

Upon arrival performed maintenance. Indoor motor & wheel are in bad condition. Motor is leaking oil, bad bearing. Blower wheel is completely dirty. Plenum are in bad condition, very dirty. Heat exchanger has slot of heat marks, did not identify any breaches. Evap coil is clogged causing air restrictions. Return air is very undersized for system. Temp rise 57. No insulation in attic. System was reset tested and fully functional upon departure. Darren to come out and give options for replacement.

Upon arrival performed maintenance. Indoor motor & wheel are in bad condition. Motor is leaking oil, bad bearing. Blower wheel is completely dirty. Plenum are in bad condition, very dirty. Heat exchanger has slot of heat marks, did not identify any breaches. Evap coil is clogged causing air restrictions. Return air is very undersized for system. Temp rise 57. No insulation in attic. System was reset tested and fully functional upon departure. Darren to come out and give options for replacement.

Upon arrival performed maintenance. Indoor motor & wheel are in bad condition. Motor is leaking oil, bad bearing. Blower wheel is completely dirty. Plenum are in bad condition, very dirty. Heat exchanger has slot of heat marks, did not identify any breaches. Evap coil is clogged causing air restrictions. Return air is very undersized for system. Temp rise 57. No insulation in attic. System was reset tested and fully functional upon departure. Darren to come out and give options for replacement.

Inspected the system

225 error code

Performed Fau maintence on Bryant system. Cycled furnace for heat. Verified proper heating sequence of operations. Temperature rise across heat exchanger is within range. Amp draws are a little high but within range. Blower wheel is extremely dirty, as well as back of motor housing. Motor is starting to leak oil. Secondary motor control is within range. Tested and verified safety components are working accordingly. Wiped down heating compartment and components. Replaced 1 inch filter. 14x25x1. Went over recommendations. Also Recommended yearly membership for maintenances. Homeowner only wants to do today’s maintenance. Cycled system, system operational upon departure.

Freddy to finish install. Special filter

Check up

Upon arrival performed heating maintenance on 2015 unit. Filter was dirty replaced it 16x20x1. Temperature rise was good. Gas shut off valve working properly. Amps on inducer motor and blower motor ok. Burner assembly looks good. Blower wheel does have dust build up. All electrical components look good. Cycled system on and off. System is operational upon departure.

Upon arrival performed AC and heating maintenance. Inspected indoor unit. Amps on blower motor good. Wheel and evaporator coil look clean. All electrical components are tied on correct. Temperature rise good as well. Inspected outdoor unit. Primary motor control looks good. Fan motor amps good as well as compressor. Cycled system on and off. System is operational upon departure.

Performed systems tune up and maintenance on the heating system. Checked electrical controls and measured motor amp draws. Measured temperature rise and cleaned filter. Removed blower motor and checked heating exchanger.

Tested system electrical and measured temperature splits. Cleaned the blower cabinet and remove the dust from the blower housing and motor. Replaced filter. Inspected ductwork. Inspected the heat exchanger.

Heating systems check and maintenance. Checked all electrical parts and monitored operation. Cleaned burner assembly and furnace cabinet. Wiped down blower motor compartment.

Upon arrival did not do furnace tune up. Customer had a couple of questions about the ducts and had one completely off. Also saw furnace is a premier furnace and told them it could possibly be on a recall due to them starting fires. Customer wants senior technician out to give replacement options.

Day 2 of install

Doing a single system Furnace tune up out here in Vista.