Vista, CA

Tech arrived on site. Performed ac tune up. Cleaned condenser coils and inspected motors. Condenser motor is leaking oil. Checked electrical. Components are okay. Refrigerant charge seemed low at the time due to outdoor temp being low. Temp split is good. System is running on an obsolete refrigerant. Attic ducts are I’m good condition. Filtration is poor. Lots of dirt getting into the unit. Flushed out drain lines. No form of flood protection is currently installed. Unit is operational upon departure.

Customer is going to pay with a check

Upon arrival, replaced all 4 filters. Condenser fan motor control is weak. Evap coils are extremely dirty and need cleaning. Thermostat in working order. Amperages are not so efficient. System is running on higher side of electrical. Temp splits good. Blower wheel dirty. System is operational, client gonna get a hold of land lord. For repairs .

Upon arrival, replaced all 4 filters. Condenser fan motor control is weak. Evap coils are extremely dirty and need cleaning. Thermostat in working order. Amperages are not so efficient. System is running on higher side of electrical. Temp splits good. Blower wheel dirty. System is operational, client gonna get a hold of land lord. For repairs .

Upon arrival, replaced all 4 filters. Condenser fan motor control is weak. Evap coils are extremely dirty and need cleaning. Thermostat in working order. Amperages are not so efficient. System is running on higher side of electrical. Temp splits good. Blower wheel dirty. System is operational, client gonna get a hold of land lord. For repairs .

Upon arrival, replaced all 4 filters. Condenser fan motor control is weak. Evap coils are extremely dirty and need cleaning. Thermostat in working order. Amperages are not so efficient. System is running on higher side of electrical. Temp splits good. Blower wheel dirty. System is operational, client gonna get a hold of land lord. For repairs .

Inspected the systems airflow and drew up a duct map to make recommendations to balance the home.

Performed AC and Fuenace maintenance on a Lennox system. Burner operation was checked. Flame sensors and limit switches were cleaned and verified in correct working condition. Filter is ok. Heating temperature split is in range at 33. Blower compartment is clean and spinning freely. Outdoor unit was chemically cleaned. Compressor bay and service panel was cleaned. Refrigerant levels were verified in range and recorded. Starting components were measured. Compressor and fan amp draws are good. System was running st end of appointment. Customer had questions about thermostat. A full tutorial was given for the sensi thermostat and customer is happy at end of appointment.

Performed Ac maintenance on Lennox condenser.

Performed AC maintenance on a Lennox condenser. Upon arrival customer reports poor airflow to a single room. This room is a home office with equipment, 1 small register. Did full duct inspection using 3 separate attic accesses. Ended up adjusting airflow to that zone in the s30 thermostat and also adjusting a register to push more air. Filter is dirty but customer is going to purchase his own. Outdoor unit was deep cleaned and given a tuneup. All data was recorded. Customer signed up for monthly maintenance to keep system working at a standard. Unit was working at end of appointment.

Condenser may be on back order, until installation Cool Air Solutions is liable to keep systems up and running until installation

Upon arrival performed diagnostic, found compressor to not be kicking on for cooling mode. Found secondary control to be out of range. Replaced and got system gojng. Temp splits in range. Client needs to move fencing around condenser so we can do a tune up. Filter is extremely dirty and needs t0 be replaced. Client signed up for maintenance program. System is operational upon departure.

Upon arrival performed diagnostic, found compressor to not be kicking on for cooling mode. Found secondary control to be out of range. Replaced and got system gojng. Temp splits in range. Client needs to move fencing around condenser so we can do a tune up. Filter is extremely dirty and needs t0 be replaced. Client signed up for maintenance program. System is operational upon departure.

Upon arrival performed diagnostic, found compressor to not be kicking on for cooling mode. Found secondary control to be out of range. Replaced and got system gojng. Temp splits in range. Client needs to move fencing around condenser so we can do a tune up. Filter is extremely dirty and needs t0 be replaced. Client signed up for maintenance program. System is operational upon departure.

Upon arrival performed diagnostic, found compressor to not be kicking on for cooling mode. Found secondary control to be out of range. Replaced and got system gojng. Temp splits in range. Client needs to move fencing around condenser so we can do a tune up. Filter is extremely dirty and needs t0 be replaced. Client signed up for maintenance program. System is operational upon departure.

Performed AC maintenance on a Lennox system. Customer recently changed filter. Electrical connections and starting components were verified in range. Refrigerant levels were verified. Outdoor unit was chemically cleaned. System was running at end of appointment. Customer is very happy with the performance of the system and also with cool air solutions.

Summer AC Maintenance Performed Upon arrival system is working and operational. I began my maintenance at the outdoor condenser, customer declined condenser cleaning service today due to company. I inspected electrical components for wear and tight connections. I checked refrigerant pressures and charge. I tested system amperages. I then proceeded to the indoor furnace unit. I measured temperature splits. I checked condensates for proper drainage and safety. Filter was changed. Inspected electrical to ensure tight connections and monitor wear. Inspected blower compartment for dust and dirt as well as proper balance. Upon inspection of both units, I found there to be no electrical protection on either, recommend having surge protection added to protect sensitive electrical components. Upon departure system is working and operational.

Arrived on site to diagnose a no cooling 2003 unit. Condenser in back yard. Client stated they lived i home for 5 years and few days back unit stop blowing cold air. Cycled unit and both indoor and out door unit both were operational just blowing warm air. Inspected electrical compartment components. Found secondary completely bad and primary starter was burnt up on contacts and is original to home. Highly recommended replacing both to keep system operating. Replace secondary and ran system. Checked start up amps and are high due to age and inefficiency. Recommend compressor booster kit to help prevent hard start up and help prolong compressor life as much as possible before it fails. Run amps is pulling 13 and max rated at 18. Advised compressor working hard from age and operation. As it is on borrowed time. Checked pressure and found unit to use R-22 that’s no longer In production. Pressure are stable and cooling hole at 18 degrees. No protection on unit and recommended adding sur

Return for Service: Blower Housing Pull and Clean Upon arrival system is working and operational. Removed blower housing from unit, taking care to disconnect and reconnect fan motor as well as moving control board for access. Proceeded to take the housing outside and wash with water and chemical solutions removing dirt and debris from the scroll wheel and housing, reinstalled and tested to confirm proper operation. Upon removal of housing I found the blower motor to be leaking oil as well as have shaft play, informed member of pros and cons of replacing blower motor. Upon departure system is working and operational.

Performed diagnostic on 15 year old system. Homeowner states system is not cooling and outdoor fan is not spinning. He did try to buy the parts but they would not let him without a contractor license. Cycled system for cooling. Indoor unit kicks on and blows air. Outside the compressor turns on but the condenser fan motor is not spinning. Checked outdoor unit electrical and system components. System is getting all proper voltage. Found a bad secondary motor control that was not allowing fan motor to turn on. Was also low on hermetic side. Put in a temporary secondary motor to fully inspect system. Cycled system on and system started cooling. Refrigerant pressures are in range and system is cooling correctly. Amp draw on condenser fan motor is above it’s rated capacity. Compressor amp draw is in range. System is older and working inefficiently but is still cooling. Went over all findings and recommendations with homeowner. He is fully aware of the condition of the system and any conce

Summer AC Maintenance Performed Upon arrival system is working and operational. I began my maintenance at the outdoor condenser by breaking it down and cleaning with water and coil solution, removing dirt and debris. I inspected electrical components for wear and tight connections. I checked refrigerant pressures and charge. I tested system amperages. I then proceeded to the indoor furnace unit. I measured temperature splits. I checked condensates for proper drainage and safety. Filter needs to be changed, member said they will go purchase and install. Inspected electrical to ensure tight connections and monitor wear. Inspected blower compartment for dust and dirt as well as proper balance. Upon inspection of the indoor furnace unit, I found the secondary motor control to be leaking castor oil and to be far below its rated values, as well as the blower compartment to be heavily laden with dirt and debris. Recommended and replaced motor control, and on the 15th of September are comin

Performed AC maintenance on 8 year old system. Cycled for cooling. Checked indoor and outdoor unit electrical and system components. Replaced filter. Pulled outdoor condenser fan motor and thoroughly washed out condenser coil inside and out. System is operational upon departure. Did speak to homeowner about Air Purification system buyback program, wants to hold off today.

Performed AC maintenance on a Lennox condenser. Systems cooling temperature split is 16 degrees. Indoor amp draws are ok. System has history ofn leaks, inspected evaporator and condenser with a UV light with no findings. Outdoor unit was dirty but chemically washed. Start and run amps are high, recommending an assist kit. Refrigerant levels are ok at this time. System was running st end of appointment.

Summer AC Maintenance Performed Upon arrival system is working and operational. I began my maintenance at the outdoor condenser by breaking it down and cleaning with water and coil solution, removing dirt and debris. I inspected electrical components for wear and tight connections. I checked refrigerant pressures and charge. I tested system amperages. I then proceeded to the indoor Air handler. I measured temperature splits. I checked condensates for proper drainage and safety. Filter was changed. Inspected electrical to ensure tight connections and monitor wear. Inspected blower compartment for dust and dirt as well as proper balance. Upon inspection of outdoor condenser I found the compressor to be pulling high amperage upon start up, recommend adding a compressor saver kit lower wear on compressor as well as lower start up amperage. Installed compressor saver kit on system. Upon departure system is working and operational.

Upon arrival performed maintenance on hvac unit. Washed outdoor coils off completely. Secondary motor control is in range. Primary starter good. Tested disconnect fuses. Advised client compressor is pulling 146 amperages , Max of 150. Recommended booster kit to bring amperages down in range. Ducting is strapped correctly, do not see any kinks or damages. Attic insulation in good condtion. Condensate pump in working order. Running amps on compressor in range. Condenser fan motor is showing signs of Leaking oil. Refrigerant levels are in range. System is operational.