Vista, CA

Performed furnace maintenance on 2018 Lenox

Performed furnace maintenance on 2009 Bryant two stage heater. Upon arrival homeowner Jeff was not present for the maintenance although was informed about everything over the phone and check sheets were left for him. During the maintenance I did come across multiple points of concerns. 1. Flame sensor was heavily oxidized, if the condition worsens this will result in System Not being able to ignite 2. Indoor Blower compartment is heavily covered in dust and debris due to 1 inch filter inefficiently stopping the dust particles from getting inside of the air mixing cabinet. This is causing the scroll wheel to become Heavily dirty and add extra weight which can cause the motor to overwork. 3. System is not equipped with surge protection in the case of a power outage thunderstorm or brown out. 4. Rat droppings and secretions were present on the top of the unit. Homeowner states that those were previously there and are old. 5. Recommend the 20 x 30 x 1 filter in ceiling should be swapped ou

Tech arrived on site and performed heating tune up. All components are Okay. Gas flex is inside cabinet. Should be hard piped out. Ducts are new but not sized properly. Heat rise is almost at max. All motors are good. Advised client on issues. Client declined to hear recommendations at this time. Unit is operational upon departure.

Job walk

Arrived on site to diagnose a no heating unit. Heater located under home. Client stated he see unit has power and hears it operating but doesn’t not create flame or heat. Inspected unit and all electrical components and connections. Found unit to operate but had a error code for a soft lock out. No sending flame. Found gas valve in furnace to be off. Turned on and unit was operational. Client stated he was interested in adding Ac to home but would like to get someone out here to go over replacement options. Will be turning call over to Jay as he will be coming on the 22nd at 10-11am for replacement options. Clients are aware and will be expecting him then. System is now operating upon departure. Client are happy with today’s visit. Closing up for maintenance plan monthly.

Replaced thermostat. Tested system with new thermostat. Inspected low voltage wires.

0-down 18 months 0% interest available

Performed heating maintenance on a 2002 Payne gas furnace. System is heating degrees, static pressure is high. Inducer motor is amping high and not spinning well. Primary motor is amping ok. Heat exchanger was inspected for damage. Many heat spots are present, also heat spots kn the front panel. No visual cracks were found today. Blower wheel is very dirty, this needs to be cleaned. The condition of the furnace was explained to the homeowners. They’re goal is to replace in the next few years. A request for repair estimates was made. System is operational at this time.

Arrived on site to perform diagnostic on a 2011 unit. Client stated he is selling home and needs unit operational. Upon arrival he stated we were just out and now Ac unit is not working and I advised him we were out last for the heater and Ac had not been touched then. Cycled unit and condenser would not start. Inspected all components and checked and found unit not getting voltage to condenser and inspected and found high voltage fuse went bad. Replaced and cycled unit and evaluated unit and advised client of findings. Primary starter is burnt up a bit but from age and operation. Secondary control was good. Fan motor is leaking oil and was advised las Ac tune up. Recommend replacing motor as it will fail soon as it’s pulling over max amps as it’s been over working in its past years. Went over all findings and recommendations but he Staters he hair wants minimum to get unit operational and would advised the client of the report. Clouds hold off on other repairs and left the new fu

Upon arrival performed maintenance on 1989 carrier unit. Dusted off all electrical components and inside of system. Found indoor motor to be leaking oil, cleaned off all debree with towel. Dirty blower wheel. Gas valve in working order. Dusted off burners. Temp rise is in range. Examined heat exchanger box to make sure system is safe and operational. Sprayed soap water to exchanger and examined inside of box, did not find any breaches or damages. System is older. Tried calling home owner, he did not answer. Tenant paid for tune up. Circuit board has burn marks in terminals. System is operational.

Upon arrival performed maintenance on 1989 carrier unit. Dusted off all electrical components and inside of system. Found indoor motor to be leaking oil, cleaned off all debree with towel. Dirty blower wheel. Gas valve in working order. Dusted off burners. Temp rise is in range. Examined heat exchanger box to make sure system is safe and operational. Sprayed soap water to exchanger and examined inside of box, did not find any breaches or damages. System is older. Tried calling home owner, he did not answer. Tenant paid for tune up. Circuit board has burn marks in terminals. System is operational.

Upon arrival performed maintenance on 1989 carrier unit. Dusted off all electrical components and inside of system. Found indoor motor to be leaking oil, cleaned off all debree with towel. Dirty blower wheel. Gas valve in working order. Dusted off burners. Temp rise is in range. Examined heat exchanger box to make sure system is safe and operational. Sprayed soap water to exchanger and examined inside of box, did not find any breaches or damages. System is older. Tried calling home owner, he did not answer. Tenant paid for tune up. Circuit board has burn marks in terminals. System is operational.

Upon arrival performed maintenance on 1989 carrier unit. Dusted off all electrical components and inside of system. Found indoor motor to be leaking oil, cleaned off all debree with towel. Dirty blower wheel. Gas valve in working order. Dusted off burners. Temp rise is in range. Examined heat exchanger box to make sure system is safe and operational. Sprayed soap water to exchanger and examined inside of box, did not find any breaches or damages. System is older. Tried calling home owner, he did not answer. Tenant paid for tune up. Circuit board has burn marks in terminals. System is operational.

Upon arrival performed maintenance . Cleaned entire system off coils were extremely dirty. Indoor motor and wheel good. Filter was dirty. Signed client up with membership & filter add on. Amperages throughout system in range. Client declined surge protector right now. But In spring she will do it. Dusted of furnace cabinet. Condensation pump in range. Tested electrical fuses. Air flow good throughout home. System is running efficient.

Upon arrival performed maintenance . Cleaned entire system off coils were extremely dirty. Indoor motor and wheel good. Filter was dirty. Signed client up with membership & filter add on. Amperages throughout system in range. Client declined surge protector right now. But In spring she will do it. Dusted of furnace cabinet. Condensation pump in range. Tested electrical fuses. Air flow good throughout home. System is running efficient.

Upon arrival performed maintenance . Cleaned entire system off coils were extremely dirty. Indoor motor and wheel good. Filter was dirty. Signed client up with membership & filter add on. Amperages throughout system in range. Client declined surge protector right now. But In spring she will do it. Dusted of furnace cabinet. Condensation pump in range. Tested electrical fuses. Air flow good throughout home. System is running efficient.

Upon arrival performed maintenance . Cleaned entire system off coils were extremely dirty. Indoor motor and wheel good. Filter was dirty. Signed client up with membership & filter add on. Amperages throughout system in range. Client declined surge protector right now. But In spring she will do it. Dusted of furnace cabinet. Condensation pump in range. Tested electrical fuses. Air flow good throughout home. System is running efficient.

Performed heating maintenance on a Goodman furnace. Combustion blower is at max amps. Flame sensor is very oxidized. Ignitor is reading ok. Primary blower is leaking oil and overamping. Switches were tested and cleaned. Duct runs are pinched and poorly installed,not sealed. The system is choking due to a small return and many supply ducts. The customer is aware of the fragile condition. His goal is to leave it alone and fix it as the problems arise. Home does not have AC and homeowner is ok with current configuration. System was operational at end of appointment.

Performed heating maintenance on a 2021 Lennox furnace. Controls were tested and verified in range. Tightened and cleaned sensors and switches. Filter is dirty customer is going to replace. Combustion blower and primary blower are amping ok. Gas valve was tested. Temperature rise is dialed at 60 degrees. Customer wants to call in later for his renewal due to the fact that he is still covered until April. System is operational at this time.

Performed furnace maintenance on a 2016 Lennox system. First time startup for heat this year. Filter is clean today. Gas valve was tested. Sensors cleaned and tested. Ignitor in range. Static pressure is good. Temperature rise is 60 degrees. Thermostat is accurate and homeowner is happy with it. Combustion blower and primary blower amp draws are within spec. System is not protected homeowner wants to research into any extra protection. The outlet the furnace is plugged into has a loose connection and was powering on and off. The homeowner is aware and is going to call his electrician. I tightened what I could and had the system running fine at end of appointment.

Performed heating maintenance on a Lennox furnace. Homeowner and his caretaker report equipment working good. Furnace starts up good. A Merv11 filter was provided. Temperature rise is within spec. Sensors and switches were cleaned and tested. Ignitor and gas valve were tested. Blower wheel is amping good and spinning freely. Combustion blower is in range. Start components were measured. Duct inspection found very old duct board ducts. The homeowner was briefed on the issues of this style is duct, he states he has no issues with them. System is not electrically protected. System was operational at end of appointment.

Performed furnace maintenance on 2011 Carrier furnace. Upon arrival Anita stated that System Has been working fine and any findings can be emailed over to her husband. Also informed client that she is up for renewal on maintenance plan. System inspection checked out properly. Temperature rise was within range. Amperages for indoor blower and inducer motor were in range. Circuitboard did have burn marks in the middle of board, Recommend surge protection is installed to prevent any damages from power outages thunderstorms etc. Flame sensor was heavily oxidized as well and can prevent System from igniting. Drain lines are clear. Filter needs to be swapped everyone to three months. Informed and discussed full condition of system with Anita and she is Would like everything emailed over to August her husband. She is also unsure whether they would like to renew the maintenance plan due to them planning on moving this year maintenance plan is transferable but she would still like to talk with

Replaced the icomfort thermostat with a S30 model.

Inspected the systems airflow and drew up a duct map to make recommendations to balance the home.

Tech arrived on site. Performed furnace tune up. Client had replaced his entire system recently. System was clean and install was up to code. Tested all electrical components, static, and temperature rise. All checked out.