Vista, CA

Arrived on site to find system locked out. Proceeded to indoor furnace and found that gas valve switch was in off position. Turned back on and also adjusted speed tap to due undersized return. System began heating properly with a 51 degree rise. Upon departure heater fully operational.

Replaced high limit switch

Upon arrival, installed new gas valve. Secured all fittings and performed a gas leak check. Tested system operation twice. Fired up both times. System is operational upon departure. 1 year parts/labor warranty.

Upon arrival, client said furnace would work intermittently. Testing found the gas valve was receiving power when the board called for it, however the valve was stuck closed. Determined the valve was defective. Went over repair options with the client. Client moved forward with the repairs amid the monthly service plan. Shut gas off to the system in case the valve worked and wouldn’t close. Heating is mot operational upon departure.

Removed dirty filter. Tested primary limit switch for continuity. Ran heat and measured supply air temp, reduced gas valve pressure. Changed filter. Ordered new high limit switch.

Check/Cash Price - $12,827 0% 18 months - $750 6.99% 120 months - $156/mo If $3000 Tech Clean California rebate becomes available client will receive afterwards. System also comes with Total Home Comfort Guarantee ensuring system provided will be suited best for clients home, and that we will be liable to address issue if sizing is causing non-sufficient heating/cooling.

Performed heating maintenance on a 1994 weather maker gas furnace. Customer reports frequent use of the heating and air due to children and elders j. The home. System also has had extensive repairs done to the electrical components. Sensors and switches were cleaned and tested. Filter was extremely dirty. Heat exchanger was hydro tested with customers consent. This passed the test but is has significant heat spots which is signs of near failure. Evaporator coil was heavily caked in dirt, this was cleaned today to aid with normal performance of the unit. Nest thermostat was installed. The condition was deeply explained to the homeowner. Homeowner is preparing to replace systems but not immediately. System is operational.

Performed maintenance on a 2019 carrier gas furnace. Heating temperature split is very high at 71 degrees. This was adjusted at the gas valve which brought the temperature rise within manufacture spec. Filters are clean. Sensors and switches were cleaned and tested. Whole home purification was installed today. System is operational.

Upon arrival, found system line wires to be burnt. Exposed wires touched the panel and caused a small electrical fire. Fixed wiring and tested system. System would fail on high pressure. Found filters to be restricted. Removed filters and system is operational again. Both motors on the unit are old and rusty and should be replaced. Maintenance on system is strongly recommended.

Performed furnace diagnostic on 1986 carrier heater. Upon arrival Ronald stated that they just moved in around September and have now noticed from only using the heater for about a week it is now continuously running and blowing cold air but not heating. Ronald mentioned the previous homeowner did not take good care of system and did not maintain. Performed full safety inspection and electrical check and found many points concerns that were addressed. 1. Furnace high limit switch that is located in natural draft compartment was Repetitively tripping. This is due to the high temperatures building up within this area 2. Measured airflow and found that it is on the brink of being past it’s allowable airflow design of 0.50 WC. Measured an actual reading of 0.50 as well but this was without a filter inside. Filter that was in system is a Merv 11 which is more restrictive and will cause airflow restrictions and combined with the heavy dust buildup in air mixing cabinet. 3. Evaporator coil

Upon arrival found 1 2 ton furnace. System is clean and client is on top of the filter. Tested heating operation. Found no issues with heating components. Temp rise is good. Duct system is all new. Could have been installed better. However client doesn’t have airflow issues. Insulation is good. Only issue with system is there is only 1 form of drain protection. Recommend adding a safety switch to help prevent flood issues. System is operational upon departure.

Combo Tune Up Performed- performed maintenance on 2020 Lennox system. Upon arrival system is working and operational. I began my maintenance at the outdoor unit by breaking it down and cleaning with water and solution. Removed heavy amounts of dirt and debris. I then inspected all electrical components for signs of wear and checked for tight connections. I measured amp draws and recorded refrigerant pressures. I then proceeded to the indoor furnace unit. Here I took temperature splits and measured static pressures. I inspected the condensate lines for proper drainage. I checked electrical components for tight connections and wear. Inspected the blower housing for balance and dust. Checked heating components for wear. Inspected heating components for proper operation. Filter has been checked and needs to be changed at this time, home owner declined and said would replace themselves. Upon inspection of the indoor unit I found the static pressure to be very high due to the dirty filter, r

Arrived on site to perform fall tune up on a 10 year old York unit. Client stated no issues as she lived in home just a few years. Cycled heater and is good no issues she stated. She wanted filters replaced as she supplied them and replaced. Unit is hanging due to no solid wood bad in attic as it is very small and clean Babel to access everything. Due to design of home and when they put unit in. Showed client and she is aware. Blower is dusty as lack of filter change out. Motor is okay at this time and in range for now. Inducer motor is operational and in range. Temperature rise is good and ducting and airflow okay as ducting is new. Drain lines unalienable to inspect or access due to them facing back and Corner of attic roof. Drain pump was operational. No protection on unit and recommended adding sur protection to unit to protect from electrical surges and power outages that can damage or even short out systems and components. Client was interested in replacing thermostat and wante

Installation of Variable Speed 19 SEER Slim line condenser with compatible coil and furnace. System totals out to $16,180 before Tech Clean Californias rebate of $3,000 applies bringing clients pay off total to $13,180

Post job walk

Performed fall maintenance on a 2015 SL280. Temperature split is in range. Inducer Blower and primary blower are amping ok. Battery cap for the inducer is leaking oil significantly. This was replaced today. Filter is clean. Blower wheel is clean. Sensors and switches were cleaned and tested. Gas valve and ignitor were tested and Recorded. System is operational at end of appointment.

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance at the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been checked, does not need to be changed at this time. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of of the indoor unit as well as the outdoor I found there to be no form of electrical protection on either unit. Recommend having surge protection added to ensure longevity and protection of the system. Upon departure system is working and operational.

Programmed the thermostat which was set for heat pump and electric heat, this is a gas furnace / standard ac. Tested the heat and measured temperatures. Fan speed was set for high on heat, adjusted the speed taps and monitored the temp rise. System is working properly at this time. Highly recommending keeping the cover door over the furnace open when using the heat or cooling. This covers the furnace and looks nice but it completely restricts the airflow, this can cause the heater to get too hot and shut off, or the cooling to get too cool and freeze up.

Upon arrival performed diagnostic. Client stated thermostat was not operational. Found thermostat to not be holding charge, he wired everything correctly. He is gonna return thermostat to Home Depot to try and get it returned.

Upon arrival performed diagnostic. Client stated thermostat was not operational. Found thermostat to not be holding charge, he wired everything correctly. He is gonna return thermostat to Home Depot to try and get it returned.

Upon arrival performed diagnostic. Client stated thermostat was not operational. Found thermostat to not be holding charge, he wired everything correctly. He is gonna return thermostat to Home Depot to try and get it returned.

Upon arrival performed diagnostic. Client stated thermostat was not operational. Found thermostat to not be holding charge, he wired everything correctly. He is gonna return thermostat to Home Depot to try and get it returned.

Upon arrival performed new thermostat install, client had newer nest, wasn’t able to move from Heat pump to natural gas heating system.

Upon arrival performed new thermostat install, client had newer nest, wasn’t able to move from Heat pump to natural gas heating system.

Upon arrival performed new thermostat install, client had newer nest, wasn’t able to move from Heat pump to natural gas heating system.