Moreno Valley, CA

AC Tune up in Moreno Valley

AC Tune up in Moreno Valley

AC maintenance in Moval

AC maintenance in Moval

AC maintenance in Moval

AC maintenance in Moval

Heating maintenance in Moreno Valley

Heating maintenance in Moreno Valley

Heating maintenance in Moreno Valley

Heating maintenance in Moreno Valley

Heating maintenance

Arrived on site to perform heating tune up on a 2013 lennox unit. Client stated no issues. Cycled unit and unit is operational. Found filter okay and slight dusty. Blower wheel is dusty. Motor is good and oil free. Clean flame heating home. Igniter is good. Flame sensor is okay. Inducer motor is in range and good. Drain lines are good and clear at this time. Safety switches are all good. Temperature rise is good at this time. Recommended adding a hard wire surge protectors but client bought a plug in one for now and is Better then nothing. Client stated she will be ordering her own filter and be keeping them on hand. She is aware. Cycled unit and units is operational. Went over how unit is running and conditions and client is aware and okay with so. Cycled unit and unit is operational upon departure.

Upon arrival performed maintenance. Indoor blower wheel is extremely dirty. Filter needs to be swapped every 2-3 months. Secondary motor control is out of range. This can stop that indoor motor whenever it fails completely. Dusted and cleaned entire burner assembly and heating compartment. Cleaned flame sensor out. Recommend adding some protection because circuit board has a ton of heat bubbles around terminals, that can def have intermittent issues. Replaced filter client provided. Adding a purification system would help the standard filter become higher filtration, keep indoor air quality levels clean. System is operational, called gale kver phone and went over findings. Will call us back she is at work .

Upon arrival performed maintenance. Indoor blower wheel is extremely dirty. Filter needs to be swapped every 2-3 months. Secondary motor control is out of range. This can stop that indoor motor whenever it fails completely. Dusted and cleaned entire burner assembly and heating compartment. Cleaned flame sensor out. Recommend adding some protection because circuit board has a ton of heat bubbles around terminals, that can def have intermittent issues. Replaced filter client provided. Adding a purification system would help the standard filter become higher filtration, keep indoor air quality levels clean. System is operational, called gale kver phone and went over findings. Will call us back she is at work .

Upon arrival performed maintenance. Indoor blower wheel is extremely dirty. Filter needs to be swapped every 2-3 months. Secondary motor control is out of range. This can stop that indoor motor whenever it fails completely. Dusted and cleaned entire burner assembly and heating compartment. Cleaned flame sensor out. Recommend adding some protection because circuit board has a ton of heat bubbles around terminals, that can def have intermittent issues. Replaced filter client provided. Adding a purification system would help the standard filter become higher filtration, keep indoor air quality levels clean. System is operational, called gale kver phone and went over findings. Will call us back she is at work .

Upon arrival performed maintenance. Indoor blower wheel is extremely dirty. Filter needs to be swapped every 2-3 months. Secondary motor control is out of range. This can stop that indoor motor whenever it fails completely. Dusted and cleaned entire burner assembly and heating compartment. Cleaned flame sensor out. Recommend adding some protection because circuit board has a ton of heat bubbles around terminals, that can def have intermittent issues. Replaced filter client provided. Adding a purification system would help the standard filter become higher filtration, keep indoor air quality levels clean. System is operational, called gale kver phone and went over findings. Will call us back she is at work .

Arrived on site to perform heating tune up on a 2021 American standard package unit. Client stated no issues. Cycled heater and is operational. Filter was replaced. Blower assembly and whee are good. Inducer motor is in range. All safety switches are good. Found static pressure above range. Temperature rise was in range. Igniter and flame sensor are good. At then end of the visit found unit over heating. Found heat exchanger with hot spots from over heating. Took a look around the house and found 2 vents closed in home and this was causing airflow restriction and is over heating. Opened the vents and unit is operational. Advised they need to stay open in home and filter should be changed out every 3 months. No protection on. It and recommended adding one to protect unit from electrical surges and power outage that can damage or short out Components. Cycled unit and client is aware of how unit is running. Closed unit up and went over how unit is running. Client is aware and happy we cam

Same issue from previous visit. Rodents are biting their way through the system and are nesting in furnace. I replaced pressure tubing and system took off in heating mode. Tenant is aware of issue and is going to call exterminator. Problem is going to keep happening until extermination is started. Charging for diagnostic only today. System is operation upon departure.

When I arrived at system, I was told heating didn’t work. I started with turning on thermostat to heating mode. I didn’t hear system kick on at all. I went to furnace cabinet and saw error code. Pressure switch fault was issue, rodents chewed through pressure switch tubing. Tubing had a hole in it and it was preventing system from turning on. I cut back tubing and attached back onto pressure switch. System turned on in heating and system operational. Then I started with maintenance to furnace. I cleaned flame sensor of all corrosion. I inspected blower motor and blower motor is dirty. No gas leaks to system, and gas turned on. The ducting had holes in it from rodents. I replaced air filter with one that tenant provided. Registers reached up to 110 degrees out of all vents. The system is operational upon departure.

Arrived on site and found flame sensor error code present. Took flame sensor out and cleaned off. Ran unit and system began heating properly. Upon departure unit is fully operational.

Performed a heating maintenance on a 2020 Lennox system. Cleaned and Adjust Burners. Check Combustion Air for Proper Venting. Examine the Heat Exchanger for Damage / Corrosion. Test Furnace Safety Controls. Inspect Gas Piping. Tighten Electrical Connections. Measure the Voltage and Amperage. Flush the Condensate Drains. Measure Tempurature Difference between Supply and Return Air. Vacuum Furnace Return Grille. Adjust Gas Pressure & Pilot. Clean in-place Blower Compartment. Inspect Blower Wheel for Proper Balance. Check the System's Static Pressures to Ensure Proper Airflow. Inspect Duct Connections for Air Leaks / Sizing / Insulation. Check all System Safety and Limit Switches. Clean Flame Sensor. Inspect Carbon Monoxide Detector. Check Thermostat for Proper Operation / Calibration. Filters where not changed this visit. System was fully operational on time of departure.

During my twenty point heating inspection, I started with the thermostat. Giving a call for heating, and going to furnace to start maintenance. Temp rise of 30-60 needed, I got a temp rise of 52. House heats up to designated temperature. I checked out blower motor of any dirt or debris and it’s clean. Owner will replace his own filter, It was dirty. Hot surface igniter not cracked or having white spots. Flame sensor still working good, no need to be cleaned. Ducting done correctly, and all runs intact. Inducer motor is working efficiently. House heats good and ready for winter.

Arrived on site to diagnose a leaking 1989 unit. Client stated She is original home buyer and heater is original. She has a separate insurance but when they came out they told her they don’t cover it and need it all replaced but didn’t even inspect the unit. Found unit all opened up. Return vent was open and off and inside was wet. Furnace located in closet and found wood base all wet. Drain is clogged and there is only one. No safety over flow switches. Blower assembly and wheel and whole cabinet of heater was really dirty as there is no rack to hold filter in place so dirt is just entering unit. Found motor leaking oil as there is a lot of oil build up and dirt on motor. Due to age of unit a lot of part are just worn out from age and operation. Found no good airflow upstairs. Inspected ducting and found it to be original gray flex and most of it has all deteriorated and has left the duct itself exposed with no insulation. Advised there are loosing cold and hot air in attic and fo

Arrived on site to diagnose unit not working again. Spoke to client and they stated unit just stopped blowing air. Cycled and I for was not operational. Condenser was operational and found line set and compressor frozen over. Advised issues is inside. Inspected electrical compartment and found secondary motor control for blower failed. Motor has a lot of oil that has been leaking from over working. Advised can fail in future. Put new part in and motor is operational just working hard from age and operation. Client also wanted to go over Ac recommendations. Advised primary stater was pitted on contact points from age and operation. Secondary motor control was replaced last time. Fan motor had dried up oil from past and can fail in future from over working. Compared is older and working hard. Recommend adding a compressor booster to help prevent hard start up. They are aware of what is going on and on ow it’s old. They stated they want to talk it over and see what is better side they

Arrived on site to perform AC diagnostic on 2004 system. Upon arrival clients son is in town and will be handling appointment for her. He stated that just last night the unit started blowing hot air and was not cooling down. Maintenance has not been done since 2020 and in 2013 the fuse was replaced. Began diagnostic at outdoor unit and immediately found that 30 amp fuse was blown. Inspected electrical components and found that duel secondary motor control is weak on hermetic side terminal. Condenser fan motor is also over amping. System contains R22 which is no longer manufactured as of 2020. Pressures are in range at this time. At this time Ruth’s son would like to go through with the mandatory repair and sign up on a maintenance plan to keep both AC and heater at standard twice a year. Clients are not in a position to go over replacement options and understand that system is past design life at this point. Installed components and system is operational and cooling upon departure