Menifee, CA

Heating maintenance in Menifee

Heating maintenance in Menifee

Heating maintenance in Menifee

Heating maintenance

Heating maintenance

Heating Diagnostic on 1 yr old Lennox equipment.

Heating Diagnostic on 1 yr old Lennox equipment.

Heating Diagnostic on 1 yr old Lennox equipment.

Heating Diagnostic on 1 yr old Lennox equipment.

Furnace repairs menifee

Combo maintenance on unit in attic and backyard

HVAC repairs menifee

We performed HVAC maintenance in Romoland for our client. We did a thorough inspection of the system including inspecting the fuel lines, the heat exchanger, the area around the air intake, etc. Our clients count on our professional service to keep them comfortable all year long.

HVAC maintenance menifee

HVAC maintenance

Heating maintenance and outflow in closet

Performed heating maintenance on 3 year old Lennox Elite unit. Cleaned return grate. Inspected filter and found it to be in good condition. Measured external static pressure and found it to be high at .9”WC, this is most likely due to the undersized supply ductwork which currently supplies approximately 1360CFM while the furnace and coil need 2000CFM. Flushed condensate drain line with water. Tested resistance of hot surface igniter. Cleaned flame sensor. Tested safety switches. Checked electrical connections. Temperature rise is within limits. Inducer amp draw and total system amp draw are within limits. While starting the furnace, whether jumping it out or controlling it from the thermostat the furnace does not always start. I asked Marcy if this happens to her and she mentioned that the furnace does not always start for her. During my maintenance inspection I didn’t see why this would be happening - gas valve was on, no blockages to the intake air, flame sensor and

Arrived on site to diagnose a no heating unit. Upon arrival spoke with client and she stated that her son told her the unit was not heating. She stated she never tested the unit just went of by what he said. Had her cycle the unit to see what is going on. Unit was heating upstairs. She has a zoned single stage unit. Unit was blowing a lot of air. She was surprised cause she she it’s working. Had her tests all the upstairs vents and everything was working fine. She stated she didn’t even test today either she only had downstairs running. After she verified all vents were blowing warm air she was good. Told her I was going to inspect furnace to see if any error codes popped up. Inspected heater and found it running good with no issues or error codes. Advised her the same from the past visit is she has a zone unit on a single stage unit and when running one zone only it does create airflow restriction. In heating that could be a issues. She is aware and okay okay with so as she has b

During my twenty point heating inspection, I started with the thermostat. Giving a call for heating, and going to furnace to start maintenance. House heats up to designated temperature. I checked out blower motor of any dirt or debris and it’s dirty on blower wheel. Replaced air filter for new air filter. Hot surface igniter not cracked or having white spots. Flame sensor still working good, deep cleaned sensor. Ducting done correctly, and all runs intact. Inducer motor is working at high amps and furnace also using high amps. Moved onto the upstairs unit, I shut off downstairs after I was done with my inspection. Put system in a call for heating mode. Soon as the house warmed up after thirty minutes. I checked out blower motor of any dirt or debris. Existing air filter is dirty and replaced. No gas leaks in system, everything pipe doped. Hot surface igniter not cracked or having white spots. Flame sensor still working good, deep cleaned flame sensor. Ducting done correctly, and all

Arrived on site to preform a 20 point maintenance inspection on a 9 year old Lennox System. Turned system on and verified the proper heating sequence. Checked burner assembly and inspected gas piping for any leaks, there were no leaks found at the time of maintenance. Next took a amp draw on the inducer draft motor, inducer was within he desired range, took a temp rise of the incoming air and outgoing air, temp rise was within limits, checked all safety and limit switches all we’re operating. Opened unit up and took a look at the internals, no loose connections all wires were in the correct terminals. Measured amperage of incoming fan load, FLA was in range. Cleared and drain condensate drain. Cleaned up the inside and outside unit from dust and debris. I did recommend a blower pull and cleaning as there was a thick layer of dust on the blower wheel. Homeowner will take it into consideration for the future. Filter was just recently change, however I did notice the filter was a littl

Arrived on site to preform a 20 point maintenance on a 6 year old trane furnace. Turned unit into heating mode, verified heating sequence for furnace, furnace was operating normally. Took an inducer motor amp draw, inducer motor was in range. Next took a temp rise for the unit, unit temp rise was within limits and was not over heating. Checked flue vents and gas piping for leaks, there were no leaks detected during the time of maintenance. Switched unit into cooling mode and took a total external static pressure test, static pressure was a little high furnace was rated for a .05 static pressures came back at .068, inspected ducting and and discovered the supply ducting is a little undersized. Let the customer know that the unit airflow could be improved and he would take it into consideration for the future. Blower motor was a little dirty as well, I cleaned as much as I could in place, but recommend they keep up on the filter so and change them every 30-60 days to help keep dust and d

Arrived on site to perform fall tune up on 2 2015 carrier units located in attic. Client stated no issues both units working good and heating. Cycled both. Found all filters were recently replaced. Blower assembly are both good and motors are good as well. Both inducer motors are both good and heating. All safety switches are operational. No sediment traps on both gas lines and recommended adding them for prevent issues to gas valve. Temperature rise is good on both units. Drain lines are all good on both units but advised both are good but no safety overflow switches on unit and recommended adding them to prevent over flow in attic and water damage to ceiling. Advised no protection equipped on unit and recommended adding surge protectors on unit to protect from electrical and power outages that can damage or even short out systems and components. Cycled both unit and went over all findings and recommendations. Client did hold off today and both systems are operational upon departure.

Arrived on site to pet heating tune up on a 1995 unit. Client has lived in home for about 20 years. Unit look to be original to home. Spoke to him and he stated unit was working a couple days back and yesterday unit did not heat home. Cycled unit and found no flame created. Then I cycled through the sequence and blower would turn on for safety lock out. Test for power and found power is sent to igniter. Removed igniter and found it to be bad and broken and no longer good. Installed a new igniter tested unit and unit did fire up. Due to the condition of heater once unit fired up it created a big flame roll out and advised is not good. Due to the age of unit it has past its life expectancy and can be unsafe as it keeps getting older. He is aware of it’s condition. Once unit fired up inspect unit. Found blower assembly is really dirty from all years of life operation. Found blower wheel really dirty crating stress on motor. Blower motor is working hard from age and condition and has bee

Arrived on site to preform furnace diagnostic on 2003 comfort maker furnace. Upon arrival Clients son is present Frank and he stated that system is no longer igniting. No repairs have been done to the furnace and last time we were here was related to the AC in 2021. Found that smart valve is defective an indoor blower motor as significant oil loss. Advised that system is from 2003 in any repairs do not guarantee the system and last much longer. Although any route client would like to go down we are willing to do but at this time clients mother would like to buy her own furnace install it herself. Upon departure system is non-operational in heating mode