Hemet, CA

Upon arrival performed drain install. Strapped drain, primed drain water it plumbing correctly. Added p trap and breather tube. System is operational upon departure.

Upon arrival performed drain install. Strapped drain, primed drain water it plumbing correctly. Added p trap and breather tube. System is operational upon departure.

Upon arrival performed drain install. Strapped drain, primed drain water it plumbing correctly. Added p trap and breather tube. System is operational upon departure.

Upon arrival performed drain install. Strapped drain, primed drain water it plumbing correctly. Added p trap and breather tube. System is operational upon departure.

arrived on site to perform maintenance maintenance n a 2 year old carrier unit. Client stated no issues and unit has been working good. He just replaced filter. Cycled cooling and is good. Condenser and indoor unit is operational. Washed condenser coil inside and out. Checked electrical compartment and components. Stater was good. Secondary motor control is good and in range. Fan motor is in range and free of oil. Checked compressor start up and run amps. Start up pulled 71.1 out of 78. Recommended adding a compressor booster kit to help prevent hard start up. Run amps are in range and checked pressures and pressure are good and steady. Unit is cooling hole good. Found no protection inside and out. Recommend adding surge protectors to unit to protect from electrical surge and power outages that can damage or even short out systems and components. Cycled unit and went over how u it is running and it’s condition. Client did hold off on recommended work at this time. He is aware and oka

Upon arrival performed another diag. Cut the drain line again & drain seems to be backed up again as it is going down into the ground somewhere. Advised client we have to rework entire drain take it outside through the stucco out to the gravel, maybe about 3-4 sticks of PVC, hose clamps. Left client temp cooling. Will come out Tuesday to take care of job. System is operational.

Upon arrival performed another diag. Cut the drain line again & drain seems to be backed up again as it is going down into the ground somewhere. Advised client we have to rework entire drain take it outside through the stucco out to the gravel, maybe about 3-4 sticks of PVC, hose clamps. Left client temp cooling. Will come out Tuesday to take care of job. System is operational.

Upon arrival performed another diag. Cut the drain line again & drain seems to be backed up again as it is going down into the ground somewhere. Advised client we have to rework entire drain take it outside through the stucco out to the gravel, maybe about 3-4 sticks of PVC, hose clamps. Left client temp cooling. Will come out Tuesday to take care of job. System is operational.

Upon arrival performed another diag. Cut the drain line again & drain seems to be backed up again as it is going down into the ground somewhere. Advised client we have to rework entire drain take it outside through the stucco out to the gravel, maybe about 3-4 sticks of PVC, hose clamps. Left client temp cooling. Will come out Tuesday to take care of job. System is operational.

Upon arrival client does not live at this property, has a friend living there. System doesn’t really turn on. Had primary drain clogged causing water to back up into secondary safety switch. Client wanted to do the bare minimum cause might be selling home in 6 months. Cut drain and cleared. System is now operational.

Upon arrival client does not live at this property, has a friend living there. System doesn’t really turn on. Had primary drain clogged causing water to back up into secondary safety switch. Client wanted to do the bare minimum cause might be selling home in 6 months. Cut drain and cleared. System is now operational.

Upon arrival client does not live at this property, has a friend living there. System doesn’t really turn on. Had primary drain clogged causing water to back up into secondary safety switch. Client wanted to do the bare minimum cause might be selling home in 6 months. Cut drain and cleared. System is now operational.

Upon arrival client does not live at this property, has a friend living there. System doesn’t really turn on. Had primary drain clogged causing water to back up into secondary safety switch. Client wanted to do the bare minimum cause might be selling home in 6 months. Cut drain and cleared. System is now operational.

Arrived on site to perform diagnostic. Upon arrival homeowner mentioned that his unit has been cooling correctly, but would still like it looked at. Advised can look the system over, but it would be hard to diagnose an issue if it’s working correctly. Cycled for cooling. Unit kicked on normally and started cooling. Gauged up to system and verified proper refrigerant pressures. Amp draws are within range. Secondary motor control is within range. Primary motor control is in good condition. Indoor fan motor was recently replaced. System is overall working as it should and is not showing any concerns at the moment. System is operational upon departure.

Arrived on site. System was operational. System would intermittently shut off. Float is okay. Temp split low. System is most likely over charge.

Performed diagnostic on 40+ year old unit. Homeowner states system is not cooling. She did have home warranty come out, but they are giving her the run around and basically doesn’t want anything to do with them. I cycled system for cooling. Unit came on normally, is not producing any temperature split at all. Checked outdoor unit, gauged up to system and found that system is completely flat on Refrigerant. System does have pretty obvious refrigerant leak in condenser coil. Evaporator coil is also in very poor shape. Ceiling has obvious water leak as well. Ductwork is in poor shape as well. Overall, system is in bad shape. Went over findings and recommendations. Homeowner would like to go over replacement options. Scheduled turn over for Monday. System is not operational upon departure.

Used shared data card on both circuit boards to load appropriate data to the systems. Used cool cloud app to make sure systems are communicating. System is staging and cooling properly at this time.

Arrived on site to perform AC diagnostic on train condensing unit. Upon arrival David stated that the house is under remodel due to a water leak and now the AC is no longer blowing cold air and only has a buzzing noise outside. He also mentioned that previous technician will be returning to do a filter dryer replacement on the liquid line of compressor. Began diagnostics and found duel secondary motor controls defective on compressor side terminal. Found traces of oil although electronic leak detector did not find any traces of refrigerant around the system. At this time David is staying in an Airbnb until the house is remodeled it will be waiting for Luis to return to do system repairs. David authorized for mandatory repair on the duel secondary motor control and upon departure system is operational and cooling with a 16° split which is below average

Arrived on site to perform spring tune up on a 20 year old unit. Client stated no issues. Unit is operational and barley runs it due to having a swap cooler. Cycled unit. Inspected condenser and is older unit original to home. Found thermostat wires are chewed up and advised that should be replaced as it can be a issues if they keep chewing on wires. Washed condenser coil inside and out. Found fan motor covered in oil from leaking in past years. Inspected electrical compartment and found both secondary motor control for compressor and fan motor are both out of range and getting weak over time. Recommend replacing to keep unit operating. Inspected start up and run amps. Start up was over max and is struggling to turn on. Run amps is over amps and advised compressor can fail at any time due to how hard unit is running. Pulling 22.3 and max rated at 21.6. Advised client so she is aware unit is on borrowed time. Checked pressure and pressure are steady but does hold r-22 and is no longer i

When I arrived at unit, the blower motor in furnace wasn’t working. I focused my attention at furnace cabinet and started checking every component thoroughly. Motherboard looks pretty good, blower motor is failing, has caked on goo and has a hard start every time I give a call for cool. I checked blower motor control, it was reading half the actual reading it should have. Asked for permission to swap out piece to see if we can get motor on. Motor kicked on, but had a loud start. Motor is failing and blower motor housing is also caked on with dirt. I showed pictures to owner, they are aware of what is going on in their blower housing cabinet. They are going to be speaking with supervisor Thursday afternoon from 3-5 arrival time. Today I’m charging for motor control.

Upon arrival found system not cooling. Condenser was dirty. Cleaned it out with water from the outside. Added 3.5 lbs of R410. Unit is cooling properly now.

Diagnosed error code of equipment with tech support and ran through the settings.

Performed AC maintenance on system. Cycled for cooling. Checked indoor and outdoor unit electrical and system components. Ran system through 20 point inspection. Pulled condenser motor and thoroughly washed out condenser coil inside and out. Gauged up to unit to verify proper refrigerant pressures. Temperature split is within range. Concerns with unit as it is on the older side is primary motor control is burnt and pitted at contact points. Also, secondary motor control is out of range, and lastly condenser motor is leaking significant amount of oil, meaning seals have gone bad. Went over findings and recommendations with homeowner. With approval, replaced both primary and secondary motor controls. Signed up on maintenance program. Cycled system, system is operational upon departure.

Arrived on site to perform diagnostic on a no cooling unit. Upon arrival spoke to client and he stated unit is working and would just like to get unit inspected. Cycled on and is operational. He stated would just shut of at time. Inspected electrical compartment and components. Stater is pitted from age and operation. Secondary motor control is good. Fan motor has been leaking oil and working hard. Unit hold r-22. Checked start up and run amps. Start up was high. Run amps was high due to unit working hard. Found pressure to be over charged as client had someone else in past Filled up unit. Unit holding just look over charged. Inspected attic. Found unit dirty from dirt that has entered in past. Motor is leaking. Secondary motor control is good. Drai lines are dirty but draining. No over flow switches on lines. No protection inside and out unit only cooling at 14 degrees. Cycled unit and went over all findings and areas of concerns and client is aware and is okay with so. Client did not

Upon arrival performed advanced evap coil cleaning, pumped system down and pulled coil out. Coil was completely washed. Welded lines together. Shot nitrogen through system. Added safety switch & reworked drains. Vacuumed system out. System is operational at normal pressures.