Hemet, CA

Technician arrived on site. Found the gas valve in the off position. Tenants said they tried to relight it and then turned it off. Set valve to pilot position, lit it and then turned it on. Pilot was standing. Turned thermostat to heat and the unit began to heat. Cleaned off electrical connections on valve. Recommend new pilot assembly and gas valve. Unfortunately our company doesn’t service these wall heaters. Heater was on upon departure.

Upon arrival performed maintenance on air conditioning system. Opened up system and cleaned out coils. primary and secondary motor controls are in range. Outdoor fan motor is leaking oil, does not spin freely. Refrigerant levels in range. Disconnect and fuses in working order. Dusted off all electrical components inside of furnace. Secondary motor control is out of range. Left checklist with tenant. system is operational, couple parts are beginnning to premature fail. -condenser fan motor not running freely, leaking oil - secondary motor control low System reset and tested.

Upon arrival performed maintenance on air conditioning system. Opened up system and cleaned out coils. primary and secondary motor controls are in range. Outdoor fan motor is leaking oil, does not spin freely. Refrigerant levels in range. Disconnect and fuses in working order. Dusted off all electrical components inside of furnace. Secondary motor control is out of range. Left checklist with tenant. system is operational, couple parts are beginnning to premature fail. -condenser fan motor not running freely, leaking oil - secondary motor control low System reset and tested.

Upon arrival performed maintenance on air conditioning system. Opened up system and cleaned out coils. primary and secondary motor controls are in range. Outdoor fan motor is leaking oil, does not spin freely. Refrigerant levels in range. Disconnect and fuses in working order. Dusted off all electrical components inside of furnace. Secondary motor control is out of range. Left checklist with tenant. system is operational, couple parts are beginnning to premature fail. -condenser fan motor not running freely, leaking oil - secondary motor control low System reset and tested.

Upon arrival performed maintenance on air conditioning system. Opened up system and cleaned out coils. primary and secondary motor controls are in range. Outdoor fan motor is leaking oil, does not spin freely. Refrigerant levels in range. Disconnect and fuses in working order. Dusted off all electrical components inside of furnace. Secondary motor control is out of range. Left checklist with tenant. system is operational, couple parts are beginnning to premature fail. -condenser fan motor not running freely, leaking oil - secondary motor control low System reset and tested.

Performed combo tune up on 1 year old Lennox equipment. Cycled system through heating and cooling modes. Checked indoor and outdoor unit electrical and system components. Temperature rise and temperature split in both modes are within range and system is working as it should. Replaced Merv filter with filter provided by customer. Pulled condenser fan motor and thoroughly washed condenser coil inside and out. Primary and secondary motor controls are within range and in good condition. Cycled system, system is operating upon departure.

Performed combo tune up on 3 year old Goodman equipment. Cycled system through heating and cooling modes. Checked indoor and outdoor unit electrical and system components. Checked heating components at indoor unit. Cleaned blower assembly and blower compartment. Cleaned flame sensor. Flushed out drain lines. filter is still clean.Checked outdoor unit electrical and system components. Primary motor control is in good conditions. Pulled condenser fan motor off as well as panels and thoroughly washed out condenser coil inside and out. Went over recommendations with homeowner. Cycled system, system is operational upon departure.

Performed Ac maintenance on 1995 system. We were out here a couple months ago and system was having some issues. Homeowner called her home warranty and problem has been resolved. Wants to keep the unit running for as long as possible without replacing it. Has home warranty in case any parts fail. Cycled system for cooling. Checked indoor unit electrical and system components. Temperature split is in range system cooling correctly. Checked outdoor unit electrical and system components. Primary motor Control slightly burned and pitted. Secondary motor control is within the allowed range. Amp draws for compressor and condenser fan motor high but within range. Pulled condenser fan motor off and thoroughly washed out condenser coil. Replaced 1 inch filter. Went over findings and recommendations with homeowner. Homeowner is aware of age and condition of system and is aware that it has high change of failing. Cycled system, system is operational upon departure.

Performed cooling tune up on 9 year old package unit. Cycled system for cooling. Checked unit electrical and system components. Temperature split is within range and system is cooling efficiently. Primary motor control is In good condition and secondary motor control is within range. Filter is still clean. Homeowner is unaware how to use the thermostat. Tried to show her how to operate thermostat to the best of my ability. Homeowner does not wish to renew ESA at this time. A lot going on at the moment and she is unsure what she is going to do with the home.

Arrived on site to perform combo tune up on a 2006 comfort maker system. Condenser located on side of home. Furnace and Evaporator coil located in attic. Washed condenser inside and out unit dirty. Checked electrical components and was good and unit was fully rebuilt. Fan motor is good and new. Primary and secondary motor controls are both good and new. Unit has compressor booster kit and good. Checked amp draws on compressor. Start ups are good and run amps are pulling 23 amps and Max rated at 25. Advised client how compressor is working and conditions and advisers her Compressor is on borrowed time and could fail at any time in future. System is cooling home at 23 degrees. No protection on unit. Cycled unit. Inspected indoor unit. Replaced filters client supplied. Blower assembly dirty and recommended cleaning assembly. Motor has been leaking oil out from past as dirty and oil are dried up on motor. Amp draws on motor are high as pulling 8.5 and Max rated at 12. Motor could fail at

Technician arrived on site and started performing ac tune up. Removed fan motor and started cleaning coils. No chemicals due to it being micro channel. Once cleaned checked electrical start components. No issues found at this time. Started unit and found the compressor was amping high on start up. Recommend hard start kit. All other amperages were good. Charge okay at this time. Did find a leak Schrader core and tightened it. Leak lock was present on fitting indicating a previous charge of refrigerant. Unit may have a leak but charge is good at this time. Home owner declined recommend repairs.

Upon arrival performed replacement of inducer draft motor. System is operational upon departure.

Upon arrival performed replacement of inducer draft motor. System is operational upon departure.

Upon arrival performed replacement of inducer draft motor. System is operational upon departure.

Upon arrival performed replacement of inducer draft motor. System is operational upon departure.

Upon arrival performed maintenance on 1 yo Lennox system. Opened up outdoor system entirely ran amperage test, cleaned outdoor coils. Coils built up some dust, took all doors off and cleaned coil. System is running efficient. Filter is ready to be replaced, client orders off Amazon and replaces. Circuit board and electrical connections good. UV bulb in working order. Heating order of operations good. System was reset tested and fully functional upon departure.

Upon arrival performed maintenance on 1 yo Lennox system. Opened up outdoor system entirely ran amperage test, cleaned outdoor coils. Coils built up some dust, took all doors off and cleaned coil. System is running efficient. Filter is ready to be replaced, client orders off Amazon and replaces. Circuit board and electrical connections good. UV bulb in working order. Heating order of operations good. System was reset tested and fully functional upon departure.

Upon arrival performed maintenance on 1 yo Lennox system. Opened up outdoor system entirely ran amperage test, cleaned outdoor coils. Coils built up some dust, took all doors off and cleaned coil. System is running efficient. Filter is ready to be replaced, client orders off Amazon and replaces. Circuit board and electrical connections good. UV bulb in working order. Heating order of operations good. System was reset tested and fully functional upon departure.

Upon arrival performed maintenance on 1 yo Lennox system. Opened up outdoor system entirely ran amperage test, cleaned outdoor coils. Coils built up some dust, took all doors off and cleaned coil. System is running efficient. Filter is ready to be replaced, client orders off Amazon and replaces. Circuit board and electrical connections good. UV bulb in working order. Heating order of operations good. System was reset tested and fully functional upon departure.

Replaced the S30 thermostat backplate Mount, the thermostat tablet and the smart hub. Grounded all extra low voltages wires. Replaced the air handler circuit board. Configured the WiFi network for the thermostat and connected the system to the dealer control center. Allowed dealer control access.

Arrived on site to perform from o tune up on a 2017 Goodman system. Furnace located in garage. Condenser coil is located in the backyard. Client stated no issues just thermostat was calling reminders about getting maintenance donee clearing reminders. Cleared reminders for maintenance and filter replacement. Client had energy saving club from Edison and replaced a thermostat and a eco blower motor. Cycled cooling and system was good. Washed condenser coil inside and out. Unit was really dirty and had hair from dog. Primary was good. Secondary motor control was weak and below out range from what’s its rated for the manufacturer. Advised would recommend replacing before completely get weak and low and compressor won’t turn on. Checked amp draws on compressor and fan motor. Fan motor is at its max and running. Compressor was start up amps at 40. And max rated at 67. Run amps are good and in range as compressor is pulling 5Amps and max rated at 12. Would recommend adding a booster kit

Ordered parts found inducer draft motor fan to be rubbing plastics ordered from united refrigeration.

Ordered parts found inducer draft motor fan to be rubbing plastics ordered from united refrigeration.

Ordered parts found inducer draft motor fan to be rubbing plastics ordered from united refrigeration.

Ordered parts found inducer draft motor fan to be rubbing plastics ordered from united refrigeration.