Hemet, CA

Arrived on site to perform AC maintenance on 20 year old Lennox unit. Met with homeowner, her son booked the appointment for today. Cycled System for cooling. Checked indoor unit as well as attic insulation and ductwork. Temperature split is in range and refrigerant pressures are good. No condensation safety switches on drain lines. Secondary condensation line is leaking and there is proof of water stains in the attic. Primary condensate line should be cleared out. Checked outdoor unit electrical and system components. Condenser fan motor looks to be replaced. Secondary motor control for condenser fan motor is extremely weak and out of range. Compressor secondary motor control is within range. Primary motor control is extremely burnt and pitted. Compressor amp draws are in range but high. Pulled condenser fan motor off and thoroughly washed out condenser coil inside and out. Went over findings and recommendations with homeowner. She is fully aware of the condition of the system and any

Performed diagnostic on 20 year old Rheem unit. Met with wife, Spanish speaking call. Homeowner states that system is not cooling. They have had 2 companies come out to do repairs recently. The first company told them That the system was low in refrigerant. They removed the refrigerant from the unit and recharged unit back up but with R407C refrigerant. The unit still did not work after that. Second company came out and found that the indoor blower motor was not even turning on. They replaced the motor and unit is kinda working now but not blowing cold air. Refrigerant charge is not correct as it was charged up without an indoor blower motor running. Compressor is over heating and is pulling 30 amps. Data plate on unit was removed and no information is available on unit. Homeowner also said that secondary line is leaking, but condensation lines are not even accessible as they are in the back side of the coil. Went over findings and recommendations with homeowner. Husband was mildly acc

Performed AC maintenance on a Lennox heat pump. Systems cooling temperature split is 21 degrees. Filter was dirty and changed today. Indoor coils are clear. Indoor amp draws are in range. Outdoor unit was dirty and chemically washed today. Refrigerant levels are a little low. Compressor and fan amperages are ok at this time. System was running at end of appointment.

Arrived on site to diagnose a no cooling unit that keeps on running and dose not shut off. Spoke to client and she stated both if inside and outside work just cools but is always running and never shuts off. Advised I would inspect System and components. Found primary good and a bit worn out. Secondary control is is good. Run amps on compressor are good. Checked pressure and found them to be low. Advised client of findings and she stated she wanted to recharge unit up. Advised would start to charge up and see would see how system good and how the system operates. After charging unit up found unit had a restriction in unit or thermal expansion valve. Also found filter dry to not be operating properly as is restricted and temperature splits before and after are it in range from manufacture specifications. Due to restrictions in refrigerant system is casing system to work way longer and to cool. Advised would be best to replace Thermal Expansion Valve and filter dryer to clear out any con

Arrived o site to diagnose a loud noise on a old unit. Upon arrival spoke over with owner as tenant stated unit works fine and cools but is making loud noises and dose not want to run system due to it. Upon arrival found unit operational and seemed to be working fine and they stated it’s cooling just randomly would make a loud noise. Inspected electrical compartment and found primary burnt up one pitted. Secondary control were very old but still in range. Fan motor was completely covered in oil and working hard. Compressor is working really hard and advised could fail at any time and dose use R-22. Client is aware and dose not want to put money into unit. As she know it should be replaced. Client would like to get pricing on system replacement. Due to owner and tenant and owner living in San Diego I would be turning call over to Darren as he would be calling client over the phone and give her replacement options. Client stated that would be fine and she would be happy to get replacem

Tech arrived on site. Client said the unit wouldn’t keep up with the heat. Inspection found the refrigerant charge low. Unit was installed in 84. It’s still operational. The furnace was replaced in 2002. The ducts were falling apart in the attic. Went over options to repair vs benefits of replacement. Client needs the unit to last awhile long, so it was best to do a band aid repair at this time. Client is aware of system condition and the risk of adding r22 refrigerant to an older unit. Added 3lbs of r22 to the system and it began to cool with a proper temperature split. Also did AC tune up while on site. Even with The added charge and a proper temp split, it’s still having a hard time cooling down the house during the hottest point in the day. Suggested new insulation and new ducts, also relocating it to the attic. It is suggested to set the temperature and leave it be, to help maintain temperature In the house. Unit is operational upon departure.

Arrived on site. Found out this is a rental property. Spoke with tenant and found out owner had another company come out and fix issues earlier today and tenant canceled call today as service is no longer needed.

Returned to perform diagnostic. Homeowner stated system is not operating again. In line fuse on transformer popped. Found short at outdoor unit wire. Outdoor wire needs repair as well as primary motor control is burnt and pitted. Homeowner only wants to take care of what’s broken for now until she hears back from Edison on the replacement of her system. Will replace parts as they fail until then. Replaced primary motor control and accessible wire from furnace to condenser. Replaced fuse. System is operational upon departure.

Performed diagnostic. Newer unit we installed is not cooling. We were out recently To preform maintenance. Outdoor unit not turning on. Checked for power and unit is recieving no power. Found a tripped breaker. Reset breaker, system kicked on and started cooling. Checked unit electrical and everything is in order. System operational upon departure.

Performed diagnostic on system. Model and serial numbers on unit are no longer visible, homeowner thinks it’s about 30+ years old. She had a handyman come out and try to fix it, and also had Edison come out yesterday. The handyman could not figure it out. Edison signed her up for a program where she could potentially get her system replaced through them at little to no cost, but it is going to take up to 60 days for her to get a response from them and she can not wait 60 days without air conditioning. Cycled for cooling and system is unresponsive. Checked for power and transformer was not giving out 24 volts. With homeowner approval replaced transformer. Cycled system and system came on and started cooling. Refrigerant pressures are in range and system cooling efficiently. Outdoor amp draws are high but within range. Homeowner is fully aware of the condition of the system, only wants to do immediate repair and wait and see what the answer is from the Edison program. System is fully

Repaired weak welded joint at the outdoor suction line. Removed and reversed the position of the filter drier.

Arrived on site to perform diagnostic on a 1992 Rheem unit. Unit is original to home. Condenser in back yard. Furnace and evaporator coil located in garage. Upon arrival spoke over with client and he stated unit is old but recently he noticed unit was not producing air flow. Found out door unit operational but no cold airflow. Checked indoor unit and found door switch to be by passed which is a safety issues. Found electrical board burnt up on top right corner. Found unit to get low voltage and high voltage. Jumped fan directly and wound not turn on. Jumped directly blower motor directly and turn on. Overall found control board is bad and no longer good. Would need to replace to continue diagnostic. Found blower motor leaking so much oil and going bad. Secondary motor control is bad and out of range. Blower assembly is completely dirty and build up. Cabinet needs cleaning as well. Found unit to only have one drain line and is dirty due to the amount of dirt that entered system. Also

Arrived on site to diagnose a no cooling 2005 Bryant unit. Condenser in back yard. Furnace located in attic. Spoke with client and he stated he’s had some issues but the tried to fix it himself as he has replaced the secondary motor controls himself and system still didn’t turn on. Advised I would inspect and evaluate the system. Inspected out door unit and found it not getting high voltage. Found breaker was tripped and not allowing high voltage. Flipped breaker rover and system turned on. Found start up to be over amping on start up. Found run amps pulling 25 and Emma. Rated at 28. Advised compressor is working really hard and on a hot summer day compressor is tripping breaker. Fan motor is covered in oil and pulling max amps advised could fail at any time. Checked pressure and found pressure to be good and in range. Inspected indoor unit. Found filter were just replaced recently. Blower ass And wheel is really dirty advised due to lack of Maintenance and filter change out. Evapo

System was running fine on arrival, tested cooling two times and inspected outdoor system. Removed WiFi from thermostat per client.

Financing available- 0-Down 90 days no interest no payment loan defaults to 120 months at 6.9% with NO pre-payment penalties. $116 per month.

Technician arrived on site, found 1 hydronic heat pump in the ceiling. -Changed filter -cleaned coils with evap coil cleaning chemicals. -rinsed it down with water from a sprayer. -checked all start components. -cleaned out electrical. Blower wheel and coils are heavily caked with dirt. Even after cleaning. Pressures are good at this time. Compressor amps and motor amps are okay. Unit is operational upon departure.

Replaced defective zone sensor and grounded low voltage wires at all thermostats. Tested zones individually and all together. Ensured system is cooling properly. Inspected pure air system this is working properly.

Performed AC diagnostic on 2003 Lennox Condenser. Upon my diagnostic client stated that system has recently stopped working and is no longer blowing out cold air. Although even when system was operational it still wasn’t keeping up and cooling down the home. I found multiple points of concerns that were addressed with Rosie. 3 ton condenser- 1. Outdoor condenser fan motor has become defective and is no longer cooling down the compressor or rejecting heat from the coils. This is why the system is screaming when the high pressure is relieved at the compressor relief valve. 2. Duel secondary motor control has become weak from over amping compressor and fan 3. Starter showing signs of painting and burn marks on contact points 4. System Contained R22 refrigerant which was completely phased out January 1, 2020 5. Power disconnect was not equipped with surge protection Discussed full condition of system with Rosie And she’s aware of what is going on with it at the moment. Informed her t

Tech arrived on site. Fan motor was operational on condenser but not compressor. Found the capacitor to have failed. Electrical was super dirty. Cleaned electrical panel. Replaced all start components and added a compressor savor kit. Started unit up. Unit had high pressures due to it being 92 inside the house. It was cooling at this time. Unit is operational upon departure. 1 year parts labor on installed components.

Performed diagnostic on system. 25+ years old. Homeowner states system is not cooling. Had another company come out a few years ago and told him it was low on refrigerant, but never added refrigerant because of the price. Cycled system for cooling. System came on and after about 5 minutes compressor went off on thermal lockout, and was extremely hot to the touch. System is receiving proper voltage and secondary motor control is within range. Could not check refrigerant pressures but system does have some refrigerant in it, not completely empty. Compressor is giving out. Went over findings and recommendations with homeowner. Because of the age of the equipment and the cost of a new r-22 compressor, homeowner ultimately decided that it was best to just replace the system. Would like to get quotes from other companies, advised him that we do offer price matching if from comparable company. System is not operational upon departure. Will follow up next week.

customer was not there thech waited for over 45 minutes

customer was not there thech waited for over 45 minutes

customer was not there thech waited for over 45 minutes

customer was not there thech waited for over 45 minutes

Upon arrival checked Freon levels, tested temperature inside of home and vents, air is coming at 65.5 degrees, refrigerant levels were found at the same place. Found filter drier to be having an 11 degree split. Client will call in the morning to schedule if she wants to move forward.