Hemet, CA

Upon arrival performed maintenance on AC unit. Compressor is running really high in amperage’s. Found secondary motor control to be compellty out of range. Compressor is only kicking on due to Hardstart kit. Client is not gonna replace anything the house is sold already. Circuit board and electrical connections good. Very dirty blower wheel. Refrigerant levels in range. System is operational upon completion .

Upon arrival performed maintenance on AC unit. Compressor is running really high in amperage’s. Found secondary motor control to be compellty out of range. Compressor is only kicking on due to Hardstart kit. Client is not gonna replace anything the house is sold already. Circuit board and electrical connections good. Very dirty blower wheel. Refrigerant levels in range. System is operational upon completion .

Arrived on site to perform spring tune up on a 2015 lennox unit. Condenser unit n back yard and furnace in attic. Client stated no issues and been cooling good. Cycled cooling and operational. Washed condenser coil inside and out as coil was really dirty and with dog hair. Checked electrical compartment and found starter good. Secondary motor control is good as it was replaced in past. Fan motor is good and free of oil. Checked start up and run amps both are good and in range. Checked pressure and unit is holding steady charge and good. Unit is cooling hole good and in range. Due to area around home has a lot of dust and filter is dirty and recommended replacing everything 3 months if not sooner. Client stated she will. No protection on unit and recommended adding protection to protect systems from electrical surges and power outages that can damage or even short out systems and components.

Performed 20 point inspection on Lennox unit. Thoroughly washed out condenser coil. Unit is operational upon departure.

Upon arrival found the heater but no pilot was active. Started it up and lit it. Tested system. Disabled auto scheduling on nest. Showed client how to light it and use stat. System is operational.

Performed tune up on 19 year old comfortmaker condenser. Inspected filters and tested system. Measured temperature splits and inspected ducting. Inspected he drain lines. Recorded all model and serial numbers. Tested outdoor controls and measured motor amp draws. Tightened wiring connections. Measured refrigerant charge. Cleaned inside condenser and washed the refrigerant coils. Added new brass caps to the service ports.

Made sure condenser disconnect had properly sized fuses. Removed single wall exhaust vent and installed double wall b-vent. Leveled the outdoor condenser on all sides. Added spray foam to the outdoor lineset cover to seal.

Upon arrival client said that he called us out to figure out what is going on with system and why it can’t bring down house below 73 degrees. Doors stay closed and 2 vents stay half way shut. House is about 1400 sq ft, system is running at about a 2 ton system with air flow. Not enough return to remove heat out of home on a very hot day. Attic has metal ducting with no seals on ducting joints at all. There is some connected in ductings that have big gaps. Compressor is running extremely hard in power, 4 hundred dollar electrical bill during summer. Client wants to get some quotes to replace system but will not be back to home for about 2 months. Wants to be here with wife, will call office or contact me to set it up. System is working and cools. Just cannot work at maximum capacity due to air flow issues and loss of pressure. No model nor serial .

Upon arrival client said that he called us out to figure out what is going on with system and why it can’t bring down house below 73 degrees. Doors stay closed and 2 vents stay half way shut. House is about 1400 sq ft, system is running at about a 2 ton system with air flow. Not enough return to remove heat out of home on a very hot day. Attic has metal ducting with no seals on ducting joints at all. There is some connected in ductings that have big gaps. Compressor is running extremely hard in power, 4 hundred dollar electrical bill during summer. Client wants to get some quotes to replace system but will not be back to home for about 2 months. Wants to be here with wife, will call office or contact me to set it up. System is working and cools. Just cannot work at maximum capacity due to air flow issues and loss of pressure. No model nor serial .

Upon arrival client said that he called us out to figure out what is going on with system and why it can’t bring down house below 73 degrees. Doors stay closed and 2 vents stay half way shut. House is about 1400 sq ft, system is running at about a 2 ton system with air flow. Not enough return to remove heat out of home on a very hot day. Attic has metal ducting with no seals on ducting joints at all. There is some connected in ductings that have big gaps. Compressor is running extremely hard in power, 4 hundred dollar electrical bill during summer. Client wants to get some quotes to replace system but will not be back to home for about 2 months. Wants to be here with wife, will call office or contact me to set it up. System is working and cools. Just cannot work at maximum capacity due to air flow issues and loss of pressure. No model nor serial .

Upon arrival client said that he called us out to figure out what is going on with system and why it can’t bring down house below 73 degrees. Doors stay closed and 2 vents stay half way shut. House is about 1400 sq ft, system is running at about a 2 ton system with air flow. Not enough return to remove heat out of home on a very hot day. Attic has metal ducting with no seals on ducting joints at all. There is some connected in ductings that have big gaps. Compressor is running extremely hard in power, 4 hundred dollar electrical bill during summer. Client wants to get some quotes to replace system but will not be back to home for about 2 months. Wants to be here with wife, will call office or contact me to set it up. System is working and cools. Just cannot work at maximum capacity due to air flow issues and loss of pressure. No model nor serial .

Upon arrival performed evaluation on system. Primary and secondary motor controls in range. Indoor motor and whole entire blower wheel is very new. Refrigerant levels are in very good standing, there has been a ton of repairs done to this system. Amperage’s are not outrages they look decent, there is nothing to bounce off of, no manufactured specs or model numbers and system is very old. System is r22 refrigerant. Evap coil is very clean. Heat exchanger is very old and rusted, inspected to see if I can find any damage metal. Signed client up with Memebrship. Client has home warranties, just wanted to see condition of system.

Upon arrival performed evaluation on system. Primary and secondary motor controls in range. Indoor motor and whole entire blower wheel is very new. Refrigerant levels are in very good standing, there has been a ton of repairs done to this system. Amperage’s are not outrages they look decent, there is nothing to bounce off of, no manufactured specs or model numbers and system is very old. System is r22 refrigerant. Evap coil is very clean. Heat exchanger is very old and rusted, inspected to see if I can find any damage metal. Signed client up with Memebrship. Client has home warranties, just wanted to see condition of system.

Upon arrival performed evaluation on system. Primary and secondary motor controls in range. Indoor motor and whole entire blower wheel is very new. Refrigerant levels are in very good standing, there has been a ton of repairs done to this system. Amperage’s are not outrages they look decent, there is nothing to bounce off of, no manufactured specs or model numbers and system is very old. System is r22 refrigerant. Evap coil is very clean. Heat exchanger is very old and rusted, inspected to see if I can find any damage metal. Signed client up with Memebrship. Client has home warranties, just wanted to see condition of system.

Upon arrival performed evaluation on system. Primary and secondary motor controls in range. Indoor motor and whole entire blower wheel is very new. Refrigerant levels are in very good standing, there has been a ton of repairs done to this system. Amperage’s are not outrages they look decent, there is nothing to bounce off of, no manufactured specs or model numbers and system is very old. System is r22 refrigerant. Evap coil is very clean. Heat exchanger is very old and rusted, inspected to see if I can find any damage metal. Signed client up with Memebrship. Client has home warranties, just wanted to see condition of system.

Arrived on site to perform diagnostic On furnace system. Upon arrival homeowner states that three other companies have been out and have not been able to get the furnace to work properly. She states that the system runs for a little bit and then shuts off and only blows cold air in heating mode. Began diagnostic and found that system was operational although running at very high temperature this will result in high limit switch tripping and shutting the system off prematurely before it gets to its temperature. Gas flex was directly routed to gas valve, and system is wobbly which can result in the flex breaking and leaking gas into the home. Found an evaporator coil drain line was leaking into closet space which is causing the wood to rot out. At this time the system is operational although client would like a long-term solution and full system replacement. Supervisor came out in system will be installed on Thursday

Upon arrival performed repair.

Upon arrival performed repair.

Upon arrival performed repair.

Upon arrival performed repair.

Upon arrival performed AC tune up. Refrigerant levels are to where needed in both systems. Filter were changed client provided. Blower wheels have some dust build up. Secondary motor controls on both system are both in range. Primary starter is pitted & burned at contacts. Condenser fan motor on 1 system is leaking oil and has a lot of heat marks, but still working under amperage’s. Compressor start amps and running amps in range. Indoor secondary control in range. Circuit boards both have burnt terminal spots. Systems are operational, client wants system to keep working. CleNed entire coils off. System is operational upon completion.

Upon arrival performed AC tune up. Refrigerant levels are to where needed in both systems. Filter were changed client provided. Blower wheels have some dust build up. Secondary motor controls on both system are both in range. Primary starter is pitted & burned at contacts. Condenser fan motor on 1 system is leaking oil and has a lot of heat marks, but still working under amperage’s. Compressor start amps and running amps in range. Indoor secondary control in range. Circuit boards both have burnt terminal spots. Systems are operational, client wants system to keep working. CleNed entire coils off. System is operational upon completion.

Upon arrival performed AC tune up. Refrigerant levels are to where needed in both systems. Filter were changed client provided. Blower wheels have some dust build up. Secondary motor controls on both system are both in range. Primary starter is pitted & burned at contacts. Condenser fan motor on 1 system is leaking oil and has a lot of heat marks, but still working under amperage’s. Compressor start amps and running amps in range. Indoor secondary control in range. Circuit boards both have burnt terminal spots. Systems are operational, client wants system to keep working. CleNed entire coils off. System is operational upon completion.

Upon arrival performed AC tune up. Refrigerant levels are to where needed in both systems. Filter were changed client provided. Blower wheels have some dust build up. Secondary motor controls on both system are both in range. Primary starter is pitted & burned at contacts. Condenser fan motor on 1 system is leaking oil and has a lot of heat marks, but still working under amperage’s. Compressor start amps and running amps in range. Indoor secondary control in range. Circuit boards both have burnt terminal spots. Systems are operational, client wants system to keep working. CleNed entire coils off. System is operational upon completion.

System does not have enough air flow on return ducting. Causing very little air flow to come out of supply venting. Mateo to get with client. Need more return air.