Hemet, CA

Upon arrival, started tune up on ac system. Cleaned out condenser and checked electrical. Found no issues. Motors are good. Refrigerant charge is not the best. Most likely wasn’t charged correctly during the install. Airflow and temp split is good. Unit is operational upon departure.

Upon arrival found system operational. Client said unit would make a sound on hot days. Inspected electrical. Compressor was using a lot of power. Operating pressures are extremely high. System has had no maintenance in awhile. Filter was restricted. Temperature split was low. Informed client. Client wants to explore replacement options.

Arrived on site to perform diagnostic on a 2015 Goodman unit. Spoke to tenant and he stated unit was just not cooling but had airflow. Cycled cooling on and did not blow cold. Condenser was running but compressor was not on. Advised and Inspected electrical. Found secondary secondary motor control to be completely bad out in a new one to inspect and get unit operational. Compressor turn on and checked pressures. Found unit to be really over charged and this is causing unit to work way hard then it should and being young and in this condition can cause more critical damage to compressor internally. Advised to Tim would need minimum replacing secondary control and haveing to come back and remove refrigerant to low the pressure and then see how unit is running once pressure get down tp where they should be in range. Time stated he would cover the maintenance plan for this year and the secondary motor control and Frank would cover the remover and recover refrigerant. Frank is aware and wi

Unit had leak in condenser and someone sauntered the leak shut and I came to only add refrigerant. My readings were sh 47, sc 3, osa 88. I added 4 lbs of 407C to get new readings of sh 15, sc 8, osa 89, delta 20. Offered leak dye but owner just wanted refrigerant.

Upon arrival, found electrical open. Client had tried to replace capacitor. Inspection found the fan motor capacitor had failed. Fixed wiring and installed new capacitor. Tested system. Advised client on replacement of motor. Unit is operational upon departure.

Performed maintenance on 10 year old Lennox system. Cycled for cooling. Temperature split is in Range. Ran system through 20 point inspection checklist. Thoroughly washed outdoor condenser inside and out. Installed new primary motor control as well as compressor assist kit with homeowner approval. Also installed nest thermostat but it turned out to be bad out of the box. Need to return with new thermostat and install. Office to schedule. System is operational upon departure.

Upon arrival performed diagnostic. Found system to not kick on. Fan kicked on and was running bAckwards. Replaced secondary motor control & got system up and going. At first I checked furnace to make sure there was no safety switches backed up. Filter was extremely dirty could have cause it to go bad. System is 2013 Lennox. Temp split good. Client asked if we work with home warranties. Signed client up with Memebrship. System is operational.

Upon arrival performed diagnostic. Found system to not kick on. Fan kicked on and was running bAckwards. Replaced secondary motor control & got system up and going. At first I checked furnace to make sure there was no safety switches backed up. Filter was extremely dirty could have cause it to go bad. System is 2013 Lennox. Temp split good. Client asked if we work with home warranties. Signed client up with Memebrship. System is operational.

Upon arrival performed diagnostic. Found system to not kick on. Fan kicked on and was running bAckwards. Replaced secondary motor control & got system up and going. At first I checked furnace to make sure there was no safety switches backed up. Filter was extremely dirty could have cause it to go bad. System is 2013 Lennox. Temp split good. Client asked if we work with home warranties. Signed client up with Memebrship. System is operational.

Upon arrival performed diagnostic. Found system to not kick on. Fan kicked on and was running bAckwards. Replaced secondary motor control & got system up and going. At first I checked furnace to make sure there was no safety switches backed up. Filter was extremely dirty could have cause it to go bad. System is 2013 Lennox. Temp split good. Client asked if we work with home warranties. Signed client up with Memebrship. System is operational.

Upon arrival performed diagnostic. Found system to be off, hooked up my gauges & my pressures were off by 100psi were not equal . Got system to kick on. Pressures looked pretty decent, but had a 14 degree split. Checked filter drier & has a 6-7 degree temp difference there. System is operational but not doing what client wants. Will be coming out Tuesday between 3-5 to replace filter drier.

Upon arrival performed diagnostic. Found system to be off, hooked up my gauges & my pressures were off by 100psi were not equal . Got system to kick on. Pressures looked pretty decent, but had a 14 degree split. Checked filter drier & has a 6-7 degree temp difference there. System is operational but not doing what client wants. Will be coming out Tuesday between 3-5 to replace filter drier.

Upon arrival performed diagnostic. Found system to be off, hooked up my gauges & my pressures were off by 100psi were not equal . Got system to kick on. Pressures looked pretty decent, but had a 14 degree split. Checked filter drier & has a 6-7 degree temp difference there. System is operational but not doing what client wants. Will be coming out Tuesday between 3-5 to replace filter drier.

Upon arrival performed diagnostic. Found system to be off, hooked up my gauges & my pressures were off by 100psi were not equal . Got system to kick on. Pressures looked pretty decent, but had a 14 degree split. Checked filter drier & has a 6-7 degree temp difference there. System is operational but not doing what client wants. Will be coming out Tuesday between 3-5 to replace filter drier.

Arrived on site. Changed indoor and outdoor txvs. Replaced charge. Unit is operational upon departure

Upon arrival performed Maintenance on hydroponic system. Cleaned coils off with brush and chemicals with water. Poured degreaser down drain. Tested secondary motor controls. Dirty blower wheel. Motor leaking some oil. System is very old. Replaced filter. System cools very well.

Upon arrival performed Maintenance on hydroponic system. Cleaned coils off with brush and chemicals with water. Poured degreaser down drain. Tested secondary motor controls. Dirty blower wheel. Motor leaking some oil. System is very old. Replaced filter. System cools very well.

Upon arrival performed Maintenance on hydroponic system. Cleaned coils off with brush and chemicals with water. Poured degreaser down drain. Tested secondary motor controls. Dirty blower wheel. Motor leaking some oil. System is very old. Replaced filter. System cools very well.

Upon arrival performed Maintenance on hydroponic system. Cleaned coils off with brush and chemicals with water. Poured degreaser down drain. Tested secondary motor controls. Dirty blower wheel. Motor leaking some oil. System is very old. Replaced filter. System cools very well.

Arrived on site to perform diagnostic on system. Homeowner states that system is leaking water from condensation line outside. She cleared the sink as well as connection to the sink, but it is still leaking and she feels like P trap In attic needs clearing. Went into attic to check unit. Secondary port from coil drains right into the drain pan and secondary line is tied to pan. Opened up coil and found primary line clogged at port as well as p trap. Cleared out condensation line. Poured a couple gallons of water to prime trap as well as test proper draining. Evaporator coil is dirty as well as bottom of drain pan, which can cause p trap to clog again. Unit is not equipped with any safety switches. Cycled system for cooling and checked outdoor unit electrical and system components. Amp draws on unit are high, causing unit to work hard and inefficiently. Unit is older, and uses r-22 refrigerant, but temperature split is within range. Went over findings and recommendations with Alicia. S

Arrived on site to diagnose a unit not cooling. Unknown age but is older. Client stated them just moved in couple days ago and unit ran and then stopped cooling. Inspected unit and unit was operational just not cooling as good. Inspected electrical compartment. Both secondary motor controls are good and have been replaced. Fan motor has been leaking oil. Primary starter is pitted on contact points. Blower motor is leaking oil as well and is really dirty. Indoor secondary was good. Checked pressure found unit to be low and advised unit could have a leak since it’s low. Advised found home to have a very small return and is affecting the amount of air entering unit and with unit being low on charge as well. Indoor coil started icing over due to under charge and air flow restriction. Unit holds R-22 and is no longer in production. Advised client of findings and she is aware of issues and what’s happening. She stated she is not trying to put a lot of money into unit as they just moved i

Upon arrival performed maintenance on AC system. Indoor motor is in hood condtion. Primary and secondary motor control in range. Found burnt wires for compressor, red tripped wire and fixed. Added booster kit cause compressor was kicking on at 124 amps, dropped down to 14.4. Refrigerant levels in range. Washed condenser coil. Client did not have funds to do Memebrship today will call in a month when he gets paid. System is operational.

Upon arrival performed maintenance on AC system. Indoor motor is in hood condtion. Primary and secondary motor control in range. Found burnt wires for compressor, red tripped wire and fixed. Added booster kit cause compressor was kicking on at 124 amps, dropped down to 14.4. Refrigerant levels in range. Washed condenser coil. Client did not have funds to do Memebrship today will call in a month when he gets paid. System is operational.

Upon arrival performed maintenance on AC system. Indoor motor is in hood condtion. Primary and secondary motor control in range. Found burnt wires for compressor, red tripped wire and fixed. Added booster kit cause compressor was kicking on at 124 amps, dropped down to 14.4. Refrigerant levels in range. Washed condenser coil. Client did not have funds to do Memebrship today will call in a month when he gets paid. System is operational.

Upon arrival performed maintenance on AC system. Indoor motor is in hood condtion. Primary and secondary motor control in range. Found burnt wires for compressor, red tripped wire and fixed. Added booster kit cause compressor was kicking on at 124 amps, dropped down to 14.4. Refrigerant levels in range. Washed condenser coil. Client did not have funds to do Memebrship today will call in a month when he gets paid. System is operational.