Fallbrook, CA

Upon arrival performed maintenance. Washed condenser coils. Refrigerant levels are in range. Comoresssor has high start amps. Secondary motor control in range. Blower wheel clean. Filter needs to be replaced, client is ordering. Thermostat in working order. System was reset tested and functional upon completion.

Upon arrival performed maintenance. Washed condenser coils. Refrigerant levels are in range. Comoresssor has high start amps. Secondary motor control in range. Blower wheel clean. Filter needs to be replaced, client is ordering. Thermostat in working order. System was reset tested and functional upon completion.

Arrived on site to perform diagnostic. Spray foam around line set is coming off and homeowner would like it redone. Applied new spray foam around lineset. Also went behind the lineset in crawl space to fully seal. Went ahead and performed maintenance. Cycled system for cooling. Checked indoor and outdoor unit electrical and components. Homeowner just replaced filter. Amp draws within range. Primary and secondary motor controls in good condition. Pulled condenser motor and thoroughly washed condenser coil inside and out. Refrigerant pressures are within Range. System is operational upon departure. Renewed maintenance program.

Technician arrived and reprogrammed ECM motor at the condenser as it was not kicking on. The reason being the power outages reset the programming. The fan motor is now in working condition. Technician also performed a spring tune up for the clients AC system. Amperage draws for the compressor, blower motor, and fan motor were all within range. The capacitor was also within proper Microfarad range. The electrical components were in good working condition. The refrigerant levels looked good, super heat and subcool were within range. Customer wanted to replace existing Honeywell thermostat with new Nest E thermostat. Technician thoroughly cleaned the condenser coil and got all of the debris out of it to improve efficiency and longevity of the system.

Technician arrived and reprogrammed ECM motor at the condenser as it was not kicking on. The reason being the power outages reset the programming. The fan motor is now in working condition. Technician also performed a spring tune up for the clients AC system. Amperage draws for the compressor, blower motor, and fan motor were all within range. The capacitor was also within proper Microfarad range. The electrical components were in good working condition. The refrigerant levels looked good, super heat and subcool were within range. Customer wanted to replace existing Honeywell thermostat with new Nest E thermostat. Technician thoroughly cleaned the condenser coil and got all of the debris out of it to improve efficiency and longevity of the system.

Technician arrived and reprogrammed ECM motor at the condenser as it was not kicking on. The reason being the power outages reset the programming. The fan motor is now in working condition. Technician also performed a spring tune up for the clients AC system. Amperage draws for the compressor, blower motor, and fan motor were all within range. The capacitor was also within proper Microfarad range. The electrical components were in good working condition. The refrigerant levels looked good, super heat and subcool were within range. Customer wanted to replace existing Honeywell thermostat with new Nest E thermostat. Technician thoroughly cleaned the condenser coil and got all of the debris out of it to improve efficiency and longevity of the system.

Technician arrived and reprogrammed ECM motor at the condenser as it was not kicking on. The reason being the power outages reset the programming. The fan motor is now in working condition. Technician also performed a spring tune up for the clients AC system. Amperage draws for the compressor, blower motor, and fan motor were all within range. The capacitor was also within proper Microfarad range. The electrical components were in good working condition. The refrigerant levels looked good, super heat and subcool were within range. Customer wanted to replace existing Honeywell thermostat with new Nest E thermostat. Technician thoroughly cleaned the condenser coil and got all of the debris out of it to improve efficiency and longevity of the system.

4 ton coil and condenser

Cleared primary drain was backed up compellty.

Cleared primary drain was backed up compellty.

Cleared primary drain was backed up compellty.

Cleared primary drain was backed up compellty.

Arrived on site and performed AC maintenance on two year old mini split unit

Arrived on site to diagnose a no cooling unit Amanda unit. Client stated unknow age and could be original. They advised me they are planning to move in the next 2 months out of state just to wants to get unit running They stated unit just did not cool and it was just airflow. Cycled cooling and indoor unit did turn on filter was just replaced and good. Inspected outdoor and fan was running and did not hear compressor. Inspected electrical compartment. Recommend getting units maintenance. But since client dose not plan on being In home for long so did not want the maintenance plan. Checked starter and it’s okay looks to have been replaced. Secondary motor control was good on compressor and fan. Checked compressor and was not hot. Wired unit back up and tried to start up unit and unit did turn on but was compressor sounded bad. Advised unit could have gotten locked up or just compressor is struggling to turn on now due to age. Recommend adding a compressor booster kit to help start

arrived on site to replace maintenance kit on a humidifier kit on a 2010 lennox unit. Client is aware just coming to replace kit. Cleaned out housing and installed new maintenance kit. Client is aware and happy we came out.

Performed tune up on Lennox heat pump. Measured temperatures and checked filter. Recorded electrical data. Cleaned outdoor system. Verified charge.

Arrived on site to inspect humidifier not working. Client stated it needed maintenance. Found unit and looks to have not been replaced. Client it would need kit replaced. Found filter kit to needed maintenance kit as well as UV light are out. Advised air scrubber needs maintenance as well. As light is very dim and can fail as it’s been 2 years since last maintenance kit. Client just wanted maintenance for humidifier kit. Would have to order and kit first and replaced. Office will call once kit comes in. Client is aware.

Arrived on site to perform spring tune up on 3 year old unit. Condenser on side of home. Furnace located in laundry room. Client stated no issues and she has yet to run unit. Cycled cooling and is good. Washed condenser coil inside and out. Checked electrical compartment and components. Primary starter is good. Secondary motor is good as it was replaced last summer. Fan motor is good and free of oil. Checked compressor start and run amps. Start up is good as they added a compressor booster kit. Run amps are good and in range. Checked refrigerant pressure and and are good and steady cooling home at 22 degrees. No Protection on unit. Inspected indoor unit. Filter is good. Blower assembly slight dust but good. Area around home is very windy. Motor is good and in range. Advised no protection on indoor unit as well. Went over all findings and recommendations and client did hold off. Cycled unit and is operational upon departure.

Performed combo maintenance on Lennox unit. Cycled system through modes. Checked indoor and outdoor units. Checked filters. Temperature splits on range. Cleaned off heating components. Checked outdoor unit electrical and system components. Pulled off condenser panels and thoroughly washed out condenser coil inside and out. Surge protection on units still good. Healthy climate purification kit will need to be replaced soon. Cycled system, system operational upon departure. Homeowner would like her humidifier serviced. Humidifier was installed behind the unit and access to it is extremely minimal, need to have smaller technician come out and gain acesss to humidifier.

Arrived on site to perform furnace maintenance on 2006 package unit. Dan said that the system has been working fine and he said no issues and they rarely used it this winter. Perform safety inspection and maintenance to furnace and found a few points of concerns. 1. Single secondary motor control has become weak Reading at 3.4 µF. This component powers the inducer motor in heating mode 2. Circuitboard had burn marks 3. System was not equipped with surge protection 4. Filter needs to be swapped everyone to three months 5. Spark ignition is oxidization although still operational at this time this component is responsible for igniting the system and heating mode 6. Flame sensor was also cleaned Discussed Maintenance with Daniel and he is aware of the condition at this time. He would like to hold off on any recommendations and have them emailed over but would like to sign up on the monthly maintenance plan to keep the system at a standard. Client was renewed in system is fully operational

Heating Maintenance performed- upon arrival system is working and operational. I began my maintenance at the outdoor unit by breaking it down and cleaning the coil. I checked amp draws and recorded refrigerant pressures. I inspected electrical components for wear and tight connections. I then proceeded to the crawlspace to access the air handler. I checked system pressures and recorded temperature splits. I inspected electrical components for wear and tight connections. Inspected blower wheel for balance and amp draws. Upon inspection of the outdoor unit I found the secondary motor control to be weak, the condenser fan motor to be close to overamping and seizing as well as high amp draws on compressor and amps. Upon inspection of the indoor unit I found there to be a significant amount of mold growing in the system between the evaporator coil and the entire inner air handler housing as well as the blower housing and scroll wheel to be heavily impacted with dirt and dust. Upon departur

Combo Tune Up Performed- Upon arrival system is working and operational. I began my maintenance at the outdoor unit by breaking it down and cleaning with water and solution. Removed heavy amounts of dirt and debris. I then inspected all electrical components for signs of wear and checked for tight connections. I measured amp draws and recorded refrigerant pressures. I then proceeded to the indoor furnace unit. Here I took temperature splits and measured static pressures. I inspected the condensate lines for proper drainage. I checked electrical components for tight connections and wear. Inspected the blower housing for balance and dust. Checked heating components for wear. Inspected heating components for proper operation. Filter has been checked and needs to be changed at this time, home owner declined and said would replace themselves. Upon inspection of both unit I found there to be no form of electrical protection on either unit, recommend adding surge protection to both units to

Cooling Maintenances Performed- Upon arrival systems are working and operational. I began my maintenance at the outdoor condensers. I began by popping the top and washing the coil out with water and solution as well as removed debris. I then proceeded to inspect the electrical components for wear and tight connections. I measured amp draws and recorded refrigerant charge. I then proceeded to the indoor furnace units. I performed a duct leakage inspection on both systems. I checked electrical components for wear and tight connections. I flushed condensate lines. I measured temperature splits as well as static pressures. Filters have been checked, do not need to be changed at this time. Thermostats were inspected for proper operation. Upon inspection of both systems I found there to be no form of electrical protection on any unit, recommend adding surge protection to all four units to protect the sensitive electrical components contained within the systems. Upon departure systems are wo

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance in the attic by performing a duct leakage inspection. I then proceeded to the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been changed, cool air provided. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon departure system is working and operational.

Upon arrival performed maintenance on heating system. Opened up system and found filter to be extremely dirty. Advised we need to swap these out every 2 months. Indoor blower wheel is dirty, client is aware. Offered to have surgery protection installed in system to protect any electrical components. Client thinks it’s a good idea, wants me to get a hold of wife. Circuit board and electrical connections in range. Client will replace filters. Cycled system on and off. Thermostat in working order. System is operational upon completion.