Fallbrook, CA

Client stated no heating for 5 ton package unit -A system has power, propane is present -Inducer motor is working properly, as well as pressure switch -However, the igniter is not receiving any voltage from the control board, resulting in the flame not being lit -The control board board needs to be replaced to get the heating elements back up to speed -Along with the igniter as it is in pretty rough condition

Client stated thermostat was blank -I took thermostat off and tested voltage between R and C -I had 24v, and I also jumped heating out to see if it would turn on, which it did -The diagnosis is that the thermostat is bad and needed to be replaced -A new Sensi Touch thermostat was installed and set up to the clients phones -System is now working properly

Arrived on site to diagnose a no heating unit 2004 Amana unit. Unit located in closet. Client stated they have just moved in and home was passed down from family. They have yet to run heater and when they reuse it ran and recently they said unit just blows cold. Had client cycle heater and blower kicked in instantly. Opened up electrical compartment. Found unit to be restricted from drain when installed. Found filter to be completely clogged. Removed and found dunce cut out to also be blocked off so return side is reduced the amount. Of air going in making it a restriction. Inspected electrical and rest unit. Blower whee covered in dirt build up. Blower motor is working hard due to restriction and build up. Found once unit was put to get there placed coil facing wall so there is never going to be access to the evaporator coil if needed. Cycled heater and got heater to operate. Cycled a couple time to ensure it won’t shut off. Found heater and ac are both from 2004 and hold r-22. Wen

Performed a heating maintenance on two Lennox heat pumps. Test Furnace Safety Controls. Tighten Electrical Connections. Measure the Voltage and Amperage. Flush the Condensate Drains. Measure Tempurature Difference between Supply and Return Air. Vacuum Furnace Return Grille. Clean in-place Blower Compartment. Inspect Blower Wheel for Proper Balance. Check the System's Static Pressures to Ensure Proper Airflow. Inspect Duct Connections for Air Leaks / Sizing / Insulation. Check all System Safety and Limit Switches. Clean Flame Sensor. Inspect Carbon Monoxide Detector. Check Thermostat for Proper Operation / Calibration. Filters where not changed this visit. System was fully operational on time of departure.

Arrived on site to preform heatpump maintenance on Lennox unit

Replaced PCO healthy climate kit. Everything is operational upon departure.

Performed a hearing maintenance on a 2020 Goodman system. Cleaned and Adjust Burners. Check Combustion Air for Proper Venting. Examine the Heat Exchanger for Damage / Corrosion. Test Furnace Safety Controls. Inspect Gas Piping. Tighten Electrical Connections. Measure the Voltage and Amperage. Flush the Condensate Drains. Measure Tempurature Difference between Supply and Return Air. Vacuum Furnace Return Grille. Adjust Gas Pressure & Pilot. Clean in-place Blower Compartment. Inspect Blower Wheel for Proper Balance. Check the System's Static Pressures to Ensure Proper Airflow. Inspect Duct Connections for Air Leaks / Sizing / Insulation. Check all System Safety and Limit Switches. Clean Flame Sensor. Inspect Carbon Monoxide Detector. Check Thermostat for Proper Operation / Calibration. Filters where not changed this visit. System was fully operational on time of departure.

Performed heating maintenance on Lennox heating system. Ran system through 20 point inspection. Merv filter is dirty, should be replaced. Would recommend replacing full Kit as bulbs on filtration system are burnt out. Air scrubber bulb and catalyst should be replaced as well. Homeowners want to take care of filtration Kit first, and worry about purification Kit later. Need to order replacement kit and return to replace. System is operational upon departure.

Returned to install iComfort S30 thermostat because previous generation thermostat had failed. Removed old thermostat and replaced with new S30. Installed Smart Hub and ensured system works properly and that Jim knew how to operate it. Upon departure system is operational.

Arrived to diagnose inoperative thermostat. Thermostat is a Lennox iComfort that has failed; the display is blank and doesn’t respond to tapping on the screen. Mr. Doty would like it to be replaced with the new S30 thermostat. The owner also mentioned that he had talked to someone about the thermostat not operating correctly over a year ago, it was not connecting to the Lennox server. He would like us to look into why this was and confirm that it will not happen in the future with the S30 thermostat. Upon departure system is operating however the thermostat is not.

Client stated thermostat malfunctioning -Thermostat was not communicating with new ac -Thermostat needed to be replaced, and some wiring needed to be changed inside furnace to make it compatible -New Sensi thermostat installed, system is working properly in heating and cooling

Performed FAU tuneup on 3 year old Lennox unit. Cleaned return grates. Inspected filter. Flushed condensate drain line. Inspected blower compartment, blower wheel is clean and balanced. Inspected electrical connections. Tested all safety switches. Cleaned in place blower compartment. Tested external static pressure and found it to be high, I noticed a couple of supply vents closed and this may be causing the pressure to be a bit high. Inspected flame sensor. Tested resistance of hot surface igniter. Temperature rise is within limits. Upon departure system is operational.

Technician arrived to diagnose condensate leak -Drain pan was tested prior to any repairs -The pan was holding water, no signs of there being any cracks in drain pan -I noticed that the condensate lines were not ran properly, they were going uphill in a few areas and needed to be reworked -Also the p trap underneath sink was clogged up -Condensate lines were cleared out, along with under the sink -Everything releveled and ran properly -Safety switch was also installed to ensure if the secondary line clogs up as well, it will kill the power to system instead of causing a leak -After repairs, lines were tested with a few gallons of water to ensure no leaking

Upon arrival unit was operational. Checked system amps they were in range, condensation line was clear , blower wheel was free of oil. Temp rise was in range and safety switches were functioning properly.

Technician arrived to perform furnace tune up -Filters were replaced -Blower motor working efficiently -Inducer motor reading proper resistance -Igniter reading proper resistance -Flame sensor clean -Airflow is well balanced

Performed a heating maintenance on two 2020 Lennox smart system’s. Cleaned and Adjust Burners. Check Combustion Air for Proper Venting. Examine the Heat Exchanger for Damage / Corrosion. Test Furnace Safety Controls. Inspect Gas Piping. Tighten Electrical Connections. Measure the Voltage and Amperage. Flush the Condensate Drains. Measure Tempurature Difference between Supply and Return Air. Vacuum Furnace Return Grille. Adjust Gas Pressure & Pilot. Clean in-place Blower Compartment. Inspect Blower Wheel for Proper Balance. Check the System's Static Pressures to Ensure Proper Airflow. Inspect Duct Connections for Air Leaks / Sizing / Insulation. Check all System Safety and Limit Switches. Clean Flame Sensor. Inspect Carbon Monoxide Detector. Check Thermostat for Proper Operation / Calibration.

Upon arrival performed maintenance on downflow system. Cleaned entire system from all dirty and debree. Washed washable filter. Added to estimate purifier to help standard filter. Circuit board and electrical connections good. Motors are all in range. Gas valve in working order. System is operational upon completion.

Upon arrival performed maintenance on downflow system. Cleaned entire system from all dirty and debree. Washed washable filter. Added to estimate purifier to help standard filter. Circuit board and electrical connections good. Motors are all in range. Gas valve in working order. System is operational upon completion.

Upon arrival performed maintenance on downflow system. Cleaned entire system from all dirty and debree. Washed washable filter. Added to estimate purifier to help standard filter. Circuit board and electrical connections good. Motors are all in range. Gas valve in working order. System is operational upon completion.

Upon arrival performed maintenance on downflow system. Cleaned entire system from all dirty and debree. Washed washable filter. Added to estimate purifier to help standard filter. Circuit board and electrical connections good. Motors are all in range. Gas valve in working order. System is operational upon completion.

Upon arrival performed maintenance on brand new AC pro units . Replaced filter client provided. Cleaned furnace cabinet. Dusted off electrical components. Gas valve in working order. Circuit board and electricals good. System operational. Thermostat good. System was reset tested and fully operational.

Upon arrival performed maintenance on brand new AC pro units . Replaced filter client provided. Cleaned furnace cabinet. Dusted off electrical components. Gas valve in working order. Circuit board and electricals good. System operational. Thermostat good. System was reset tested and fully operational.

Upon arrival performed maintenance on brand new AC pro units . Replaced filter client provided. Cleaned furnace cabinet. Dusted off electrical components. Gas valve in working order. Circuit board and electricals good. System operational. Thermostat good. System was reset tested and fully operational.

Upon arrival performed maintenance on brand new AC pro units . Replaced filter client provided. Cleaned furnace cabinet. Dusted off electrical components. Gas valve in working order. Circuit board and electricals good. System operational. Thermostat good. System was reset tested and fully operational.

During my twenty point heating inspection, I started with the thermostat. Giving a call for heating, and going to furnace to start maintenance. Temp rise of 40-70 needed, I got a temp rise of 40. House heats up to designated temperature. I checked out blower motor of any dirt or debris. It’s clean, only being a four year old system. Replaced air filter for new air filter. Owner had extra one, so just used his. Hot surface igniter not cracked or having white spots. Flame sensor still working good, no need to be cleaned. Ducting done correctly, and all runs intact. Inducer motor is working efficiently. Moved onto the upstairs unit, I shut off downstairs after I was done with my inspection. Put system in a call for heating mode. Soon as the house warmed up after thirty minutes. I got a temp rise of 46, which is perfect in my temperature rise range. House heats up to designated temperature. I checked out blower motor of any dirt or debris. It’s clean, well maintained system. Existing