Fallbrook, CA

Performed AC maintenance. Completed 20 point inspection.

Performed combo tuneup

2 system AC maintenance performed 20 points inspection

Ac maintenance

Ac maintenance

Ac maintenance

Ac maintenance

Ac maintenance

Ac maintenance

Ac maintenance

Ac maintenance

Working on the furnace performing maintenance

HVAC maintenance fallbrook

Fallbrook 👍🏼 Lennox system

Fau tune up fallbrook

Fau tune up fallbrook

Furnace maintenance fallbrook

Arrived on site to perform heating tune up on a 2006 carrier unit. Client stated no issues. Cycled heater. He will buy and replace filters himself. Advised him to be doing so every 3 months. Unit is operational. Checked electrical compartment. Blower wheel is is dirty from dirt entering unit. Motor is good. Slight dried oil. But in range of amps. Inducer motor is in range of amps. Unit is heating home up good. All safety switches are good. Drain lines both primary and second got to the same line. No safety over flow switches. Recommended adding one to prevent water overflow in attic. Igniter okay. Flame sensor is really oxidized from use. Cleaned but still worn out. It’s still operational just not the best condition. Temperature rise is in range and heating. No protection is on unit and recommended adding to protect unit from electrical surges and power outages that can damage or even short out unit and it’s components. Cycled unit and went over how unit is running. Went over rec

System qualifies for 2 promotional financing options: Reduced 7.99% apr at 320 per month or 18 months with payment no interest

Performed furnace maintenance on 10 year old Maytag unit. Replaced filter with new MERV 11 filter. Flushed condensate drain with water. Temperature rise is within limits. Tested external static pressure and found it to be high, this is due to the undersized and inefficient supply duct layout. Inspected blower compartment and found blower wheel to be clean and balanced. Checked all electrical connections. Tested resistance of hot surface igniter. Tested safety switches. Prior to departure I ensured the furnace was operative after my maintenance inspection.

Promotional financing options available: 18 months no interest or Reduced 7.99% apr at 61 per month

Arrived on site to perform tune up on 2 2002 Rheem units. Client stated they have just moved in about a year and half ago and haven’t got units looked at and would like to to know what they have and how it’s doing. Client stated she hasn’t had any issues in heating or cooling and both are operational. Cycled both and both are good. Did ac maintenance washed out both coils inside and out. He led electrical compartment on both units. Found both secondary motor control have been replaced. Primary starter is original and is getting pitted from age and operation. Recommend replacing both. Found both fan motors to be leaking a lot of oil from use and over working in past years. Advised motors are on borrowed time. Checked start up on compressor. Find both compressor to be running hard at this time and how cold it is amps are still high in range and advised in summer once it gets 100 it could be almost at max. Being that’s it’s working a bit right now shows in summer it’s pulling

Heater is kicking on for one second and turning off<br> -I diagnosed that the control board is the cause of the issue<br> -I relayed to the customer that these older furnaces have a lot of switch and relays and that the control board may not be the only issue<br> -He would like to just pay the diagnostic fee

Arrived on site to perform furnace diagnostic on 1988 comfortmaker heater. Upon arrival Chris stated over the phone that system is creating burning smell while heating the home. He recently bought the house about a year ago and he’s unsure whether or not repairs or any maintenance has been done ever. Performed diagnostic on system and found that unit is in very bad condition. Inspected heat exchanger and found severe corrosion and heatspots marks. Burning smell only starts when heat exchanger is ignited. Found no Burning smell coming from indoor blower cabinet although Cabinet is heavily covered In dirt and debris and filter has not been swapped in a very long time. Overall inspection showed that furnace is severely worn out and heat exchanger is most likely defective. Main concern would be that heat exchanger is possibly cracked in locations that are not visible. Ultimately the 34-year-old furnace is past design life becoming unsafe and unreliable. Advised Chris that there is not mu

Arrived on site to perform condenser fan motor installation and furnace maintenance. Motor was installed. Performed full maintenance on 2004 carrier heater. Found that temperature rise was extremely high indicating that heat exchanger is at risk of damage from high temps. Advised that heat exchanger is inspected and tested for any possible defects but at this time client is aware unit is from 2004 and will most likely be replacing in the near future but cannot at this moment so would like to leave it the way it is and decline safety inspection. Single secondary motor control is the coming week that supplies power to indoor blower motor. Flame sensor had carbon buildup and was cleaned off. Inspected control board and found multiple burn marks possibly due to power outages. Gas line did not have drip leg as well. Recommend search protection to prevent any further damage to control board. At this time client is aware of all possible failure points. Will be sending recommendations over in