Canyon Lake, CA

Upon arrival performed maintenance on 2021 Lennox system. Found coils extremely dirty. System did not have any room for breathing. Amperage’s we’re high in compressor when restricted but dropped when restriction was taken care of. Filter needs to be swapped out. Did not have that size on van. Advised moving up to merv cabinet to filter more. Washed out coils. Tested electrical connections. Systems is in good condition. Client not home worked with son.

Upon arrival performed diagnostic. System is not kicking on, is stuck in low pressure switch. Even when restarting entire system. Jumping switches. And nothing. Client had TXV replaced Oct 28. And tech said he couldn’t get it to kick on anymore. Ordering from Lennox. And gonna continue diagnostic when new board is in .

Upon arrival performed diagnostic. System is not kicking on, is stuck in low pressure switch. Even when restarting entire system. Jumping switches. And nothing. Client had TXV replaced Oct 28. And tech said he couldn’t get it to kick on anymore. Ordering from Lennox. And gonna continue diagnostic when new board is in .

Upon arrival performed diagnostic. System is not kicking on, is stuck in low pressure switch. Even when restarting entire system. Jumping switches. And nothing. Client had TXV replaced Oct 28. And tech said he couldn’t get it to kick on anymore. Ordering from Lennox. And gonna continue diagnostic when new board is in .

Upon arrival performed diagnostic. System is not kicking on, is stuck in low pressure switch. Even when restarting entire system. Jumping switches. And nothing. Client had TXV replaced Oct 28. And tech said he couldn’t get it to kick on anymore. Ordering from Lennox. And gonna continue diagnostic when new board is in .

Upon arrival system was operational. Checked outdoor unit because system is a heat pump. Pressures were high due to temperature outside. Amps were in range, washed unit from inside out secondary motor was in range but on the lower side. Safety switches were functioning properly. Moved to the indoor unit blew out condensation line and ducts were good , blower wheel was free of oil and debris. Upon departure unit was heating and operational.

Technician arrived to perform tune up for heat pump -Condenser was cleaned off -Refrigerant levels are within range -Blower motor clean and working properly -Filter will be replaced next visit -System is fully sealed, no air leaking -Surge protection was installed to protect S30 thermostat from electrical surges -Disconnect to air handler was also replaced as there was a broken screw and thread, causing the wire to be loose -The wire was very charred -Disconnect was replaced, everything is protected and safe now

Arrived on site to perform spring tune up on 2 units unknown age of units. Looks original to home. Cycled both units and both are operational. Filter where just replaced by client. Washed out condenser coils inside and out. Checked fan motors and one is seizing up and other is at max amps and is going to be seizing up In Future. Secondary motor control was weak and going bad on small condenser. Big condenser secondary motor control is new and looks as it was just replaced. Both primary starters are in range. Checked compressor start up and run amps are in range just high. Checked pressure and found both units holding charge of r-22 and is in range. Units are heating and cooling. Advised to client units are old and have wear and tear and advised can run but just will be having issues in future. He is aware and he stated he is just tend to ride it out. He is aware of his recommendations and repairs. He did declined and just wanted to hold off. Cycled both unit and both units are operat

Arrived on site to perform heat tune up on a 2012 Goodman unit. Condenser located in back yard. Furnace located in attic. Client stated no issues as they have just moved into home. Cycled heater and is operational. Inspected attic and found black flex duct used. Found it to be a bit under sizes as airflow is a bit restricted. Filter was replaced and found it to be a April air. Replaced it with a hepa filter for now as client has allergies. Blower assembly and coil have dust from dirt entered unit. While in attic found that a home foundation of the 2x4 has been cut and was removed and to have been done when they replaced the unit. Advised client so she is aware. Protection has been added. Inspected condenser unit. Washed condenser coil inside and out. Primary starter is good. Secondary motor control was completed bad and only started due to the kick start they had in unit. Fan side was good. Fan motor has a lot of oil that has leaked in past. Recommended replacing to help unit run easie

Performed maintenance on a Lennox heat pump. Temperature split is in range. Filter is clean. Condensate lines are clear and flowing good. Indoor coil is clean. Indoor amp draws are in range. Condenser was chemically washed. Refrigerant levels are ok. Starting components are in range. Cycled system, system is operational upon departure.

Technician arrive to install blower motor module and perform ac tune up -Module was installed and everything fired up perfectly -Condenser was cleaned out with water -Refrigerant levels are within range -Electrical components not drawing too much power -Filter will be replaced upon next visit -System is currently cooling

Error code 201, issue with blower motor -I tested resistance on blower motor, it is reading proper ohms -The blower motor module itself is not reading the proper amount of ohms, and needs to be replaced for this motor to be operational -Part is ordered from Lennox, should be at the shop by tomorrow

Upon arrival unit was operational. Started at the indoor unit checked blower wheel it was free of oil condensation lines were clear filter was clean amps were in range. Inspected ducts , and temp rise was in range. Washed outdoor unit out and checked amps . Upon departure unit was operational and heating

Tested the temperatures and inspected the ducts.

Upon arrival units were operational. Started at the outdoor units checked pressures on both units they were in range. Checked amps and secondary control motors they were in range washed both units and moved to the indoor units. Checked amps of both systems they were in range , blower wheels and condensation line were free of oil and debris. Temp splits for both units were at 20 degrees. Upon departure units were operational and cooling.

Performed an AC maintenance on a 2021 AC pro system. The clients stated that they where having an airflow problem in the upstairs area. When you got half way up the stairs you could feel a substantial difference in the temperatures. After feeling the vents there was hardly any air flow coming from them. I went into the attic and saw that the damper attached to the duck leading up stairs was almost fully closed. After opening the damper and closing certain ones downstairs half way, you could feel much more airflow coming out of the upstairs vents. System was chemically bathed and thoroughly washed. Checked pressures and temperature splits and both where in range. Checked all electrical components and everything was in range. Filters where not swapped this visit. System was fully operational on time of departure.

Technician arrived to perform maintenance for mini split and 3 heads -Condenser was cleaned out thoroughly and debris was removed -All 3 filters were washed out and dried -Refrigerant levels are at proper levels -Air flow is great, air is about 52° -Client renewed maintenance membership to keep her system nice and tuned

Upon arrival, client said airflow was poor in bathroom. Inspected ducts and found them designed and installed poorly. Made recommendations on how to improve airflow. Diagnostic fee can be applied towards project if approved within 7 business days.

When I arrived at unit, the pipes were frozen over. I went to attic to make sure blower motor was spinning and air is moving. I then noticed that the door switch stays pushed in all the way even after detaching the doors. It’s in pushed in position always and will always call for cool. I then went to filters and owner provided filters so I replaced them because they were dirty. The filters were the issue and caused a restriction on system. I then went outside to check noise out on motors I just installed. The noise is the compressor running. Both compressors running at 20 amps. Owner speaking with someone on Friday. No charge today

When I arrived at unit, the owner mentioned he tried to set up his own thermostat. Owner did the job correctly, but wasn’t sure why unit wasn’t turning on. I checked out for fuses and he didn’t pop any fuses. I then went to condenser unit to find why condenser was shut off. I started at breaker and noticed breaker was tripped. Turned breaker ON, then the unit began to work for two minutes. I could hear compressor make the loudest noise. Then it shut off and tripped breaker, I re did same thing but got an amp draw. My amp draw for compressor reached as high as 29 amps and shut off once again. Compressor will continue to do same thing, the compressor can’t be saved. Owner will be speaking with supervisor on Friday to get replacement options. Today just charging for diagnostic of 98.

Last ac maintenance visit, I recommended a rebuild on both systems. The downstairs unit failed and didn’t cool. I set a call for cool and condenser fan motor wouldn’t spin. Amp draw was exceeded for fan motor. I notified owner and he approved of all my recommendations even on other unit. I disconnected both fan motors and set to rpm needed on motors. I cut and reconnected all 24v and 120v legs to the starter. Then lastly I replaced both motor controls for systems. Both units working more efficient now, a lot less quieter than before as well due to the electronic controlled motors.

Tested equipment with Maytag tech support, replaced high pressure switch. Monitored refrigerant pressures. Tested switches to ground and voltages. Checked sensor resistance. Placed umbrella over condenser to shade the unit and cooled the coils with water to lower the pressure.

Replaced defrost board on outdoor system. Tested system on cooling before departure, system is working properly at this time.

Diagnosed defective defrost control board.

Upon arrival, system was not operational. Client said the capacitor had been replaced before by home warranty. Opened up the electrical and found the capacitor had failed again. Inspected unit and found the outdoor fan motor to be leaking oil. Found part of the condenser coil to be falling apart. Filter drier is rusted out. Installed new capacitor and tested system. Compressor is close to max amps. Fan motor is also close to max. Informed client. Client want to do the immediate repair only. Advised client on replacement options. Unit is operational upon departure.