Winchester, CA

Performed AC Diagnostic on 1999 comfort make unit. On arrival homeowner stated that a previous company was out and she did not have a good feeling about them due to them not thoroughly looking through the system or even opening up either indoor or outdoor unit. She has no idea what was wrong with the system but thermostat originally went blank. Found that the outdoor unit did have 240 V present but 24 was not. Proceeded to add it inspected 1999 furnace. transformer had 120 V present and 24 at circuitboard but was still not Turning the AC unit on while the system was jumped out at the y terminal. Determined that circuitboard is defective and ultimately System is in very bad condition and is very dirty due to dust and debris buildup. System has not been maintained at all and needs to have circuitboard installed first to proceed to next step as far as how the system runs and it’s efficiency. This is a Banda aid Repair and does not guarantee extra life for the system. Client is not in a

Performed work, vacuumed system down to 500 microns, pressurized system, and capillary tunes still icing up, refrigerant levels do not make any sense. Coil is plugged and needs replacement.. coming to install coil tomorrow.

Performed work, vacuumed system down to 500 microns, pressurized system, and capillary tunes still icing up, refrigerant levels do not make any sense. Coil is plugged and needs replacement.. coming to install coil tomorrow.

Performed work, vacuumed system down to 500 microns, pressurized system, and capillary tunes still icing up, refrigerant levels do not make any sense. Coil is plugged and needs replacement.. coming to install coil tomorrow.

Performed work, vacuumed system down to 500 microns, pressurized system, and capillary tunes still icing up, refrigerant levels do not make any sense. Coil is plugged and needs replacement.. coming to install coil tomorrow.

Performed furnace maintenance on 2010 amana Heater.

Performed leak dye search and found no evidence or traces of leak dye. Refrigerant Levels are good at this time. Performed primary drain line clear out due to call and say backing up and overflowing into secondary. Will return for winter visit in middle of November. Upon departure system is operational and cooling

Quality control check

Upon arrival performed diag, found system to be complete covered in ice. De iced system. Found my pressures to be out of wack, cleaned Evap coil as it was really restricted. System is still performing with un stable pressures, found txv to be restricted. Coming out to replace txv. System is operational.

Upon arrival performed diag, found system to be complete covered in ice. De iced system. Found my pressures to be out of wack, cleaned Evap coil as it was really restricted. System is still performing with un stable pressures, found txv to be restricted. Coming out to replace txv. System is operational.

Upon arrival performed diag, found system to be complete covered in ice. De iced system. Found my pressures to be out of wack, cleaned Evap coil as it was really restricted. System is still performing with un stable pressures, found txv to be restricted. Coming out to replace txv. System is operational.

Upon arrival performed diag, found system to be complete covered in ice. De iced system. Found my pressures to be out of wack, cleaned Evap coil as it was really restricted. System is still performing with un stable pressures, found txv to be restricted. Coming out to replace txv. System is operational.

Performed AC maintenance on a Goodman system. Cooling temperature split is 22 degrees. Filters were changed customer provided filters. Indoor mo draws are ok. Indoor blower has a slight imbalance. Condensate lines are clear. Outdoor unit was chemically washed. Service panel and compressor bay was cleaned. Starter is heavily chattering. Battery cap is in range. Compressor and fan amp draws are in range at this time. Refrigerant levels are ok. System is not protected. Customer wants to move forward with the starter and surge protection during winter visit so they cn make sure the funds at their. System was operating at end of appointment.

Upon arrival performed diagnostic. Found condenser fan motor to not be spinning. Secondary motor control is out of range and does not have any juice to kick it on. Replaced part and got system up and going. Advised client that fan motor is running over max amps. Did attic inspection. Checked motor controls up in attic. Blower wheel dirty. Thermostats in working order. Client wanted to do minimal repair, declined membership will call us if he wants to move forward.

Upon arrival performed diagnostic. Found condenser fan motor to not be spinning. Secondary motor control is out of range and does not have any juice to kick it on. Replaced part and got system up and going. Advised client that fan motor is running over max amps. Did attic inspection. Checked motor controls up in attic. Blower wheel dirty. Thermostats in working order. Client wanted to do minimal repair, declined membership will call us if he wants to move forward.

Upon arrival performed diagnostic. Found condenser fan motor to not be spinning. Secondary motor control is out of range and does not have any juice to kick it on. Replaced part and got system up and going. Advised client that fan motor is running over max amps. Did attic inspection. Checked motor controls up in attic. Blower wheel dirty. Thermostats in working order. Client wanted to do minimal repair, declined membership will call us if he wants to move forward.

Upon arrival performed diagnostic. Found condenser fan motor to not be spinning. Secondary motor control is out of range and does not have any juice to kick it on. Replaced part and got system up and going. Advised client that fan motor is running over max amps. Did attic inspection. Checked motor controls up in attic. Blower wheel dirty. Thermostats in working order. Client wanted to do minimal repair, declined membership will call us if he wants to move forward.

Post job walk and installed a circuit board

Preformed Ac Diagnostic on 2001 Goodman condenser. Upon arrival client stated that the system is no longer blowing cold out and will not drop temperature on the thermostat. During the diagnostic I found multiple points of concerns that were addressed with Daniel. Downstairs unit 3 ton- 1. Duel secondary motor control was defective on hermetic and fan side terminal due to compressor using too much power 2. Compressor is pulling 12 amps When the manufacture rated it 14 which indicates that it is beginning to use too much power and is most likely to exceed the design amps even hotter days. 3. Condenser fan motor has significant oil leakage coming from bearing 4. Compressor is locking out on start up while under a load. installed compressor saver kit to decrease the chance of it locking out. 5. Starter on upstairs unit was welded at contact points Causing the system to run continuously even when thermostat is off. Flicked starter And contacts separated. 6. System Contains R22 refrigerant

Tech arrived on site. Downstairs unit would make loud noises on start up. Found the blower wheel in furnace had failed and broke apart. Causing it to grind on the housing. Placed order for wheel. Will return when parts arrive.

Tech arrived on site. Found a bad capacitor. Installed new one. Compressor almost at max amps. Due to age of unit, client wanted to explore replacement options. Did tune up on site.

Summer AC Maintenance Performed Customer requested service only be provided to outdoor unit today. Upon arrival system is working and operational. I began my maintenance at the outdoor condenser by breaking it down and cleaning with water, no coil solution due to age and degradation of coil, removing dirt and debris. I checked refrigerant pressures and checked electrical amperages. I inspected electrical components for wear. Upon inspection of outdoor unit I found the compressor to be pulling high amperage due to old age, member is going to let the system run its race prior to replacing. Upon departure system is working and operational.

Found low voltage fuse on upstairs circuit board open. Replaced the fuses and jumped components to check for shorts. Installed customer provided thermostat and provided new batteries for the control. Tested the fan and cooling. Measured indoor temperatures and recorded model / serial numbers.

Performed AC maintenance on a Carrier unit. Systems cooling temperature split is 20 degrees. Condensate lines are clear but have no overflow switch installed. Indoor blower motor is ok and amping in range. Thermostat board has burns on the diodes I am recommending surge protection for the furnace. Outdoor unit was chemically cleaned. Refrigerant levels were verified in range. Customer reported home warranty visiting last month to add Freon and replace a battery cap. Starter was burnt up, thus was replaced today. Condenser fan motor is heavily leaking oil. System was running st end of appointment.

Job walk