Wildomar, CA

Performing maintenance on Goodman system.

Performing maintenance on Goodman system.

Performing maintenance on Goodman system.

Furnace diagnostic

Furnace diagnostic

Furnace diagnostic

Furnace diagnostic

Heating maintenance

Diagnostic

10 year old Goodman.. no heat. Rain took out the hot surface and other components

10 year old Goodman.. no heat. Rain took out the hot surface and other components

10 year old Goodman.. no heat. Rain took out the hot surface and other components

10 year old Goodman.. no heat. Rain took out the hot surface and other components

Lennox furnace 👌🏼

The client was concerned about air quality after last year's forest fires, especially VOCs. We sat down with them and discussed our wide range of filtration systems, and the client chose our "Whole Home Air Purifier." The IAQ changed dramatically in very little time.

Clean and Adjust Burners Check Combustion Air for Proper Venting Examine the Heat Exchanger for Damage / Corrosion Test Furnace Safety Controls Inspect Gas Piping Tighten Electrical Connections Measure the Voltage and Amperage Flush the Condensate Drains Measure Tempurature Difference between Supply and Return Air Vacuum Furnace Return Grille Adjust Gas Pressure & Pilot Clean in-place Blower Compartment Inspect Blower Wheel for Proper Balance Check the System's Static Pressures to Ensure Proper Airflow Inspect Duct Connections for Air Leaks / Sizing / Insulation Monitor Air Purification System Check all System Safety and Limit Switches Clean Flame Sensor Inspect Carbon Monoxide Detectors Check Thermostat for Proper Operation / Calibration

Performed furnace maintenance on 2 year old AC Pro unit. Cleaned return grate. Replaced filter with new MERV 16 filter. Measured external static pressure and filter and coil pressure drops and found it to be within the manufacturer’s recommended static pressure. Inspected blower compartment and found the blower wheel to be clean and balanced. Tested resistance of hot surface igniter. Flushed condensate drain with water. Tightened electrical connections. Temperature rise is within limits. While performing the maintenance I noticed the furnace does not have a surge protector installed. Because it wasn’t brought up during the sale I offered Matthew to install it at the install price. At this time he would not like to proceed. Prior to departure I ensured the furnace was operative after my maintenance inspection.

Tested operation of equipment and ordered parts through tech support.

Performed heating maintenance on a 2013 Trane heat pump in Wildomar CA. System is heating really well with a 25 degree split. Filter will be replaced by homeowner. Indoor coils are good and indoor blower is amping in range. The outdoor unit was chemically cleaned. Refrigerant levels were measured and are in range. Condenser motor has started to leak oil. All other components were measured and tested. The condition of the system was discussed with the homeowner. System is operational at this time.

Performed heating maintenance on 10 year old Goodman system. Cycled for heat. Verified proper heating sequence of operations. Ran system through 20 point inspection checklist. Cleaned off blower and burner compartments. Noted any concerns. Went over findings and recommendations with homeowner. Cycled system, system is operational upon departure

Arrived for isolation test check -Coil is completely flat of nitrogen -The leak is in the coil and it needs to be replaced -Service deposit was implemented of $400 -Will return January 5th 8-9am arrival to install new coil

Arrived on site to perform diagnostic on system. Homeowner states that system was working and heating fine but he tried to change his thermostat and it now doesn’t work. Did put the old thermostat back on but unit still not working. Checked unit electrical and found blown fuse most likely caused by thermostat being changed without turning power off. Replaced fused and homeowner finished thermostat configuration. Cycled system for heat, unit is back up,and running. Recommended to upgrade transformer for new digital thermostat as well as surge protecting unit to protect the board. Indoor fan motor has also lost significant amount of oil. Went over findings and recommendations. Homeowner wants to hold off as unit is working. System is operational upon departure.

20 Point Inspection: Clean and Adjust Burners Check Combustion Air for Proper Venting Examine the Heat Exchanger for Damage / Corrosion Test Furnace Safety Controls Inspect Gas Piping Tighten Electrical Connections Measure the Voltage and Amperage Flush the Condensate Drains Measure Tempurature Difference between Supply and Return Air Vacuum Furnace Return Grille Adjust Gas Pressure & Pilot Clean in-place Blower Compartment Inspect Blower Wheel for Proper Balance Check the System's Static Pressures to Ensure Proper Airflow Inspect Duct Connections for Air Leaks / Sizing / Insulation Monitor Air Purification System Check all System Safety and Limit Switches Clean Flame Sensor Inspect Carbon Monoxide Detectors Check Thermostat for Proper Operation / Calibration

Arrived on site to perform diagnostic. Homeowner states system is not heating, and it is blowing cool air fan has not shut off. He did just replace the thermostat, system was already having issues before then. First thing I noticed was fan was set to on position at thermostat. Switched to auto, fan still did not shut off. Went into attic and system was throwing error code for open flame rollout. Reset switch, cycled for heating and unit was unresponsive. Found that homeowner had wired thermostat incorrectly. Rewired thermostat. Unit came on and started heating. Unit heated for a couple mins before locking out on flame rollout once again. Homeowner had almost all upstairs vents closed. Opened all vents. System still has a very bad roll out on top heating chamber causing roll out switch to trip. Verified proper gas pressure. Cleaned heating orifices. System still rolls out when blower kicks on. This can be indication of a cracked heat exchanger causing blower to push air out of the heati

Furnace check up on system, I was here maybe a month ago. I cleaned flame sensor and patched up leak on roof. I was told when I walked through door that system was working. I stayed to make sure no error codes were making system shut off. For hour I was here the system never failed and didn’t have error codes. I did notice five vents were closed at home. I opened the, all up, got a temperature split. Temperature split was in range and house heats great. I showed owner how to use thermostat correctly. Charging for diagnostic only today.