Riverside, CA

Post job walk

Preformed furnace maintenance on 2018 Goodman heater. Found that both Uv bulbs and catalyst on air scrubber have come towards the end of its component life. These parts should be swapped out after 2 years. At this time client would like both bulbs and catalyst on truck for summer visit and a surge protector for her condenser. Client also ordered merv 16 filter. System checked out properly and was reset and tested.

Preformed furnace and heat pump maintenance on 2018 2 system.

Perform furnace maintenance on six-year-old Lennox system

Price is good through Friday. Manufacture Price increase is coming on the 15th.

Preformed annual furnace maintenance on 3 year old comfort pro. Home owner was not present during visit. Temp rise and airflow checked out properly. Flame sensor was cleaned and igniter is good. Board and blower are in good condition. Filter is good. System is working properly upon departure.

Performed furnace maintenance on a 2002 comfort maker gas furnace in riverside. Systems heating temperature split is at max with 61 degree split. Static pressure is high. Blower motor is leaking oil and over amping. Sensors and switches were cleaned and tested. Duct runs are sealed. Return duct is undersized creating a restriction inside the furnace. Given these findings of an overheating and restricted furnace a safety inspection was granted by the owner. I found multiple cracks on the heat exchanger. This furnace was condemned unsafe and gas was turned off at the unit. A full overview was given to the homeowner. Husband and wife need to discuss there options. Following up tomorrow. System is non operational at this time.

Performed furnace maintenance on a 1 year old Lennox gas furnace. Homeowner reports good operation of the furnace this year. Ducts and AC was replaced 4 years ago free of charge from a warranty company. Customer reports installers did not put back the faceplate for the outlet. I put it back on today. Filter was dirty and replaced today. Sensors and switches cleaned at tested. Heating temperature rise is in range. Furnace components are all reading in range. Homeowner was under the impression her maintenance contract was valid for several years. She is not able to renew today. System is operational.

Customer reports thermostat is on heat and cool air coming from ducts occasionally. He also reported issues with the thermostat. A quick tutorial was give. He is very unhappy with the system reporting it only works when a technician is here. I found normal operation. There is a high temperature rise. I am assuming the system is going off on high limit but it did not happen at this visit with no error codes to reference. A 1 inch filter was still installed the original return grill despite having a Merv rack this could be aiding in overheating. This was removed. System is operational at the end of appointment.

Performed maintenance on a 2017 Lennox gas furnace. Systems temperature rise is in range. Sensors and switches were cleaned and tested. Ignitor and gas valve were tested and recorded. Filter was dirty and replaced with a customer provided MERV 16. Condensate lines are clear. All error codes were checked clear. Primary blower and combustion blower are reading in range. System was cycled and is operational at end of appointment.

Performed maintenance on a 2005 Trane gas furnace. Homeowner reports good functioning furnace however no maintenance has ever been done on the system. System is heating in range. Flame sensor is very black. Ignitor is reading out of range. Blower motor is leaking oil. Battery cap is out of range and was replaced today. Blower wheel was cleaned today. Homeowner does not prefer any memberships regarding maintenance. The system is operational at end of appointment.

Performed Fau maintenance on 6 year old Rheem system. Cycled system for heating. Verified proper heating sequence of operations. Temperature rise across heat exchanger is high but within range. Merv 11 filter is extremely clogged which can be why unit is operating a little hotter than usual. Checked and ensured all registers were open. Ran system through 20 point inspection. Replaced filter with filter provided by homeowner. Filters are smaller than the cabinet And is letting through unfiltered air, and also causing some build up of dust starting to form on blower wheel. Went through findings and recommendations. Cycled system, system is operational upon departure.

Heating Maintenance Performed Upon arrival system is working and operational. I began my maintenance in the attic by performing a duct leakage inspection. I then proceeded to the furnace unit, I checked and tightened electrical connections. I inspected the heating components for proper operation and wear. Burners were inspected for proper operation. Flame sensor was cleaned. Condensates lines were inspected for proper drainage. Static pressures and temperature splits were taken. Filter has been changed at this time, Cool air Provided. Blower housing and wheel was inspected for balance and dust build up. Air supply was measured. Inspected safety switches as well as inspected home for fire and carbon monoxide detectors. Upon inspection of indoor furnace unit, I found the blower wheel to be heavily impacted with dirt and debris, recommend having a blower housing pull and clean performed to alleviate excess wear on the system. Also recommended a phenomenal air to help reduce particulates

Performed heating maintenance on a 2019 Comfort pro gas furnace. System is heating 30 degree split. Sensors and switches were cleaned and tested. Gas valve tested. Blower wheel is clean and spinning well. Combustion blower and primary blower are amping in range. Filter is clean at this time. Duct runs are sealed. Condensate lines are clear. System is protected. Homeowner was briefed on condition. System is operational.

Arrived on site to diagnose unit client stated heater is not heating. Upon arrival client stated heat did not turn on and husband called in. Inspected unit and thermostat and was operational. Cycled heater and unit started heating. Checked all notifications and errors code and found none cycled system for 10 mins and was still heating and operational. Advised client unit is working as it should and properly. Cycled unit and unit was operational and heating upon departure. Collected

Arrived on site to perform diagnostic on 1988 Carrier furnace. Homeowner states system is not heating. He ordered and replaced the ignition control module and circuit board About a year ago. Cycled system for heat. Ignitor came on, flame and gas came on for a couple seconds and then shut off. Checked for voltages at gas valve and it was still recieving proper voltage, meaning it should still be allowing gas through but it wasn’t. Gas valve is bad and needs to be replaced. Cannot determine any other issues at this time but seems like everything was working correctly. Went over safety inspecting furnace, homeowner said he’s never had an issue with it before. Went over repair costs.

Arrived on site to Perform fall maintenance on 2010 York heater. Before beginning to maintenance Tenant stated that system has been shutting on and off in heating mode and only runs for about 30 minutes. Therefore before beginning the maintenance I tested the system and it had tripped on high limit in under five minutes. Called Ms. Walker to inform her the furnace is not working, unfortunately that had made upset her Because she’s under the impression that there is something new every time we are out. This issue was actually noted and addressed on the last fall maintenance and also was noted that this will cause the system to overheat in the future. Client states that she has other properties and does not remember the email from last December. Performed diagnostic and found that the system has a Major Airflow Restrictions, Heavily Caked with Dust and debris on the scroll wheel and indoor blower cabinet, return/supply vent is undersized, and the furnace is extremely oversized for the

Preformed Ac/furnace maintenance free with installation on 2020 Lennox unit. Upon arrival client stated that system has been working great and has no questions at this time. I performed a safety inspection on heater and found no issues with sequence of operation. Temperature rise and Airflow Are in range. 1 inch Filter has not been swapped, this needs to be swapped everyone to three months. Flame sensor was cleaned. Blower wheel and motor look good. System is not equipped with surge protection. Performed AC maintenance and cleaned off condenser coil due to them being very plugged up and dirty recommend that this is done just before the summer. Compressor and fan Amperage Are in range. High voltage distributor and duel secondary motor control are in good condition at this time, Outdoor unit was also not equipped with surge protection. Both sides of the system checked out properly at this time and informed client that there is a maintenance program available to help keep the system that

Performed diagnostic on commercial package unit. Thermostat is not turning on and unit is not working. Checked for power at the thermostat, not getting any low voltage power. Went up on roof and checked system electrical and components. System is not recieving power at all. Verified all fuses are working correctly. Checked electrical panel at warehouse and found 3 pull breaker to be turned off. Was not tripped it was completely shut off. Turned breaker on and restored operations to unit. Went over findings and recommendations. They are just tenants and can not make any decisions. Going to let the owner of the building know. System operational upon departure.

Techs arrived on site and performed ac tune up of commercial package unit. Cleaned coils and electrical cabinet. Tested electrical components. Found the condenser fan motor to be leaking oil. Start caps are okay and within range but reading low. Condensate line had broken off and is leaking onto rooftop. Filters need to be changed. System is 2 stage but currently wired for 1 stage. Need to upgrade thermostat for 2 stage. Will send estimate for quarterly commercial service.

Performed AC maintenance on 2 York systems. Cycled systems for cooling. Checked indoor systems electrical and components. Temperature splits are in range. Filters are clean. Ductwork and connections are in good condition. Checked outdoor units electrical and system components. Amp draws on right side unit condenser fan motor and compressor are high, and condenser fan motor has started to leak oil significantly. Primary and secondary motor controls in good condition and in range. Pulled condenser motors and thoroughly washed out condenser coils inside and out. Renewed ESA maintenance program, wants to stay on yearly maintenance program. System is fully operational upon departure, homeowner fully aware of findings and recommendations for units.

Cleared the condensate drain

Changed out breaker, fuses, gas line and painted pvc black

Performed AC maintenance on a Lennox package unit. Heating mode temperature split is 53 degrees. Flame sensor was cleaned. Inducer motor is in range. Blower is amping in range. Filter was dirty and replaced today. Cooling temperature split is 20 degrees. Coils were extremely dirty and chemically cleaned off today to factory standards. Refrigerant pressures verified okay. Starting components were checked and verified to still be in range. Condensate lines are clear.

Upon arrival performed diagnostic, found secondary saftey switch to be backed up again. Performed a cut and clear with 400psig of nitrogen and cleared clog. System is now flowing correctly .