Perris, CA

Ac maintenance

Parts house sent the wrong part. Sent booster motor instead of blower motor. Need to return. Furnace is heating upon departure with fan mode on position.

Performed diagnostic. Unit is not heating. She had a handyman come out and told her it was the gas valve. I cycled system for heating. Flame ignites, abut blower motor never kicks on. Heating speed on fan is bad, which is why unit never heats as the fan doesn’t kick on. Used other speed tap on fan and fan comes on normally. Fan and relay have to be replaced. Need to order motor and return to replace. System is operating upon departure, but will heat slower due to slower fan speed. Homeowner is aware of age and condition of unit, Does not want to replace any time soon.

Gas Valve Covered Under Warranty . Gas valve replaced. No repipe .

Gas Valve Covered Under Warranty . Gas valve replaced. No repipe .

Gas Valve Covered Under Warranty . Gas valve replaced. No repipe .

Gas Valve Covered Under Warranty . Gas valve replaced. No repipe .

Clean and Adjust Burners Check Combustion Air for Proper Venting Examine the Heat Exchanger for Damage / Corrosion Test Furnace Safety Controls Inspect Gas Piping Tighten Electrical Connections Measure the Voltage and Amperage Flush the Condensate Drains Measure Tempurature Difference between Supply and Return Air Vacuum Furnace Return Grille Adjust Gas Pressure & Pilot Clean in-place Blower Compartment Inspect Blower Wheel for Proper Balance Check the System's Static Pressures to Ensure Proper Airflow Inspect Duct Connections for Air Leaks / Sizing / Insulation Monitor Air Purification System Check all System Safety and Limit Switches Clean Flame Sensor Inspect Carbon Monoxide Detectors Check Thermostat for Proper Operation / Calibration

Performed diagnostic on 2 year old Lennox system. Homeowner states that system is not heating. Thermostat was set to heat upon arrival, but unit was not responding. Error code on display showed that unit was locked out due to no flame sensed and to many retries to start. Cleaned off flame sensor and tried cycling unit on. System initiates heating cycle , but burners never kick on and unit continues to try until it locks out again. Gas valve is not opening to release gas. Checked for power at valve and it is recieving proper voltage. Gas valve needs to be replaced. Gas line should also be hard piped out of the furnace with a sediment trap added. Went over findings and recommendations with homeowner. With approval, he would like to replace gas valve, as well as hard pipe the gas line and add sediment trap. Gas valve will be ordered from Lennox riverside. System is not operational upon departure.

Arrived on site to perform diagnostic on package unit. Unit is not cooling. Has not worked since the middle of summer. Cycled unit for cooling. Indoor blower kicks on, but refrigeration portion of unit is not kicking on. Found a tripped low pressure switch not allowing power to make it to contactor. Gauged up to system and found Unit is completely flat on refrigerant. Condenser coil has a noticeable refrigeration leak on bottom portion of coil. Condenser coil has to get replaced, and new refrigerant would have to be added. Went over pricing and recommendations. Homeowner prefers to replace unit instead of repairing it due to cost and repairs. Mateo is scheduled to come back out on Friday from 10-12.

Arrived on site to perform furnace diagnostic on Aireflo heater. Upon arrival met with Debbie And she stated Becky is out of state. found that gas line was off. Inspected exhaust venting for upstairs system and found that it was slightly disconnected. Found that downstairs unit pressure switch was stuck open. Inducer motor has significant oil leakage as well. Filters were heavily plugged up. Debbie will be getting new filters today. At this time Debbie has decided to just do the pressure switch and hold off on any further recommendations and will talk to Betty once she gets back. Will be ordering pressure switch to get downstairs unit running panda Parcher system is non-operational and upstairs is.

Arrived on site to diagnose a no heating 2004 york unit. Client stated unit has not been heating home. Tried to run it this season and heater is not heating home. Cycled on and sounded like it was starting to operate the sequence of operation. Checked filters and found them completely clogged and hammered. Pull all the filters and cleaned vents. Client stated she will order her own and replace more often. Inspected unit. Found blower assembly and whee to be covered in dirt. Motor has been leaking over past years of operation. Inducer motor is over amping from years of wear. Fixing was okay. Found unit to not be up to code and not have any safety over flows on drain lines and recon some due to the amount of dirt that is in unit. found unit to be over heating from airflow restriction. Unit is not as efficient as it used to be and advised this is the start of unit having problems and will continue so as age goes on. She is aware. Found no protection on unit and advised if she is trying to

Upon arrival started system in cooling everything turned on and function properly, switched over to heating for the first time this season. Customer stated he had not yet tried the heating this year. Heating kicked on normally and was operational took reading of all our amperage’s and checked our safety and limit switched. All were functional and operational. Filter needed to be changed it was a Merv 11 20x25x5 filter, homeowner had an extra filter so we changed it while there on or visit. Over system was running and functioning properly.

Performed combo tune up on 1 year old Lennox system.

Rescheduled call. Waited on site until 4, nobody arrived. Office to reach out and reschedule.

When I arrived, the unit didn’t turn on in heating. I turned thermostat to heating and went to attic to diagnose issue. I saw on error codes the flame sensor needs service or filter dirty. I took out flame sensor and deep cleaned. The flame sensor was white and needed to see flat surface to ignite burners. After cleaning , wiring back up and screwed into existing spot. Furnace took off in heating mode. I also went to check filter and it was very dirty. I replaced air filter with new one. I recommend a hot surface igniter replacement in due time. Igniter is starting to get white and cracked. Only problem is gas valve is directly behind it so that will all need to be dissembled to do work.

When I arrived at furnace, I was told to inspect system. The furnace had its gas turned off yesterday from gas company. Gas company found two leaks in the gas valve and through cracked glass lens. Owner wanted to know if anything on unit is replaceable and fixable. The unit is old and can’t be restored in parts. The parts in system exceed past 40 years. I smelled gas all around unit when I turned it on. Gas valve is shut off for safety reasons. Supervisor is coming over to speak about potential replacement options. Charging for diagnostic only today.

Arrived on site to perform two System AC Diagnostic on 2005 ICP condensing units. Upon arrival client stated that downstairs is no longer blowing any air and upstairs is not cooling off. They have only lived in the house for about a year and have had multiple renovations done. Began at indoor unit for downstairs and found that single second of the motor control has failed. This is due to the indoor blower motor beginning to use too much amps and working hard overtime. Installed new single secondary motor control and motor fired up And was drawing high power. Proceeded to outdoor units and found both dual secondary motor controls were weak and out of range which can result in the outdoor condensing units failing on start up. Advised clients that systems are from 2005 in any repairs done will be considered a Band-Aid. Leo was unable to reach his father to approve repairs and will ask us to call him in a couple days but would like to just do the bare minimum repair at this time to get it

Cleared safety switch of condensate and repiped secondary drain line.

Was out here a couple days ago. Dog pulled wire out again. Reconnected wires. Advised to fence around the condenser as there is very little wire left and a new wire might have to be ran if it happens again. System is operational upon departure.

Client stated no cooling, condenser non operational -I found that the compressor was energized but fan motor was not -Capacitor was within range, so it was the condenser fan motor that went bad -Also one of the low voltage wires coming from furnace was shorted -I switched the wires and the contactor was then pulling in -The condenser fan motor was replaced -System is now operational -Refrigerant levels are very low, 72 psi, it should be anywhere from 130-135 -There is an apparent leak in the system, it is missing about 3-4 lbs -Dye kit and refrigerant was recommended as the system is still under warranty and it is recommended to find and fix the leak ASAP -Currently cooling

Arrived on site to perform diagnostic on 2003 Goodman unit. Met with tenant, who is brother of homeowner. States system is not cooling. His new dog chewed up his thermostat wire to outdoor condenser, which is why the system is not turning on. Advised have to fix wiring before doing anything else. Repaired low voltage wire, added a small piece of PVC pipe to run wires through so dog can’t chew them anymore. Disconnect box is missing front cover to protect From water. Ensured that no fuses were blown, cycled system for cooling. System came on and started cooling. Refrigerant pressures are within range. Amp draws on compressor and condenser motor are high and inefficient. Secondary motor control has burning and pitting at contact points. Temperature split is within range. Indoor wheel is dirty. Blower is also leaking oil. Went over findings and recommendations. Needs to go over everything with his brother, only wants immediate repair for today. System is operational upon departure. Lo

Arrived on site to replace bad board and bad blower wheel. Client is aware she just wanted mini to get unit up and running as it was before so she can sell home. Installed and replaced board and wheel and cycled unit and u it is now operational and cooling as it was. Showed client bad blower whee so she can see what it’s no longer good. She is aware and did see failures. She is aware unit is operational and is starting to cool home down. Unit is operational upon departure.

Arrived on site to diagnose a no working 2005 unit. Client also wanted to get a second opinion due to the recommendations needed. Spoke with client she stated it Stated with a Clogged drain lines and the secondary overflow was leaking water. Called a company put and they came and cleared lines. That same day she stated unit started making very loud rattle noises coming from the attic and this noise want happening before until the guy came and cleared them. She called back and they sent out another tech that was younger. He came out and inspected the loud noise and he told the lady that the blower wheel is and and needs to be replaced and then thermostat went blank. He the blower wheel/fan had ripped up some of the wires to the motor as stated in the invoice he gave her and that doing so popped the fuse. He replaced it and unit was still not working and he told her they needed to replace wheel first to determine if any other issue are present. She stated he told her it was a CYA pap

Performed an AC maintenance on a 2021 Lennox system. System was chemically bathed and thoroughly washed. Pressures and temperature splits where checked and both are in range. All electrical components where checked and everything was in range. Filters where swapped this visit. System was fully operational on time of departure.