Menifee, CA

Replaced bad carrier control board found the control board was not sending 24 V to contact to condenser outside replace control board and system is fully functional.

Performance tune up and cleaning

Install 5 inch filter rack Merv 11 to reduce does by 95 % filtration Along with 6 to 12 months lifespan. Install return Plenum removing Duckboard Plenum and installing sheet metal Plenum to improve your quality

Control board in furnace is no longer calling for cooling a less jumped out, Outside refrigerant pressures and electrical check out well indicate to me that control board has gone out and needs to be replaced

Had to replace original Fan blade you to shaft rusting unable to retrieve

Performed AC maintenance on 23-year-old condenser

Job walk

No charge, was estimate. Turning over to Darren to re design ducts to push more air flow to 4 rooms on left side of the home upstairs. System has 1 duct to feed 5 different rooms. Return duct undersized. Very to no little air flow. System is operational.

No charge, was estimate. Turning over to Darren to re design ducts to push more air flow to 4 rooms on left side of the home upstairs. System has 1 duct to feed 5 different rooms. Return duct undersized. Very to no little air flow. System is operational.

No charge, was estimate. Turning over to Darren to re design ducts to push more air flow to 4 rooms on left side of the home upstairs. System has 1 duct to feed 5 different rooms. Return duct undersized. Very to no little air flow. System is operational.

No charge, was estimate. Turning over to Darren to re design ducts to push more air flow to 4 rooms on left side of the home upstairs. System has 1 duct to feed 5 different rooms. Return duct undersized. Very to no little air flow. System is operational.

Also includes Merv 16 filter, new registers and new thermostat as part of promo After all rebate total will be 7478.50

Performed Diagnostic on 1981 Goetl package unit. Homeowner states that system is not cooling. It is blowing air, but not cold air. Cycled system for cooling. Went up to roof to diagnose package unit. Findings are as follows: 1. Condenser fan motor is not spinning 2. System is very old and in poor condition 3. There is a lot of rust throughout the whole system 4. Compressor has been running with no condenser fan motor, possible damage could have occured to compressor. Can not test until unit is operational 5. System uses old R-22 refrigerant. 6. Ductwork in attic is also in fairly bad condition, rips and tears in certain areas. Homeowner wanted me to just replace condenser fan motor to try and get system operational for now. Upon disassembly, found bolts completely seized and rusted so bad that they were breaking as I was trying to get them off. Bolts that attach fan blades to motor shaft are completely seized up and will not come off. System would need new fan blades, new motor mou

We will be replacing upstairs System and ducting with a new minisplit

Performed diagnostic on 2007 Lennox system. Homeowner states that system is not cooling. It is kicking on but it is just blowing hot air. After performing through diagnostic on system, the following are the concerns as to why the system is not operating: 1.Secondary motor control is completely dead for both condenser fan motor and compressor 2. Fan and compressor were both running of a hard start stick 3. System is completely flat on refrigerant. It is so low that suction line is actually at negative pressure. 4. System has already lost refrigerant in the past, so system definitely has a leak somewhere 5. Indoor unit is not installed correctly, as well as ductwork is very poorly designed Recommendations are as follows 1. Full Condenser rejuvenation 2. Recharge system and add leak dye Or 3. Nitrogen isolation test to locate leak 4. Replace or repair whatever is found to be leaking. Depending on where the leak is, it may not be repairable and a coil might be replaced. 5. May be t

Performed diagnostic on York system, age is unknown but Home was built in 1990’s homeowner believes. Homeowner states that her condenser is not kicking on. Cycled thermostat for cooling , condenser is unresponsive. Found low voltage wires to be completely chewed through. Repaired wiring, system kicked on. Performed thorough inspection of unit, and although it is cooling, it does have quite a bit of concerns: 1. Secondary motor controls for fan and compressor are very out of range 2. Condenser fan motor is over amping and is leaking oil 3. Primary motor control is burnt and pitted 4. Compressor is pulling in fairly high amps, but Within range. 5. Indoor blower motor is also leaking good amount of oil 6. Indoor blower wheel is completely dirty Went over findings and recommendations. Homeowner is aware of everything that is going on with her system and understands what can potentially fail in the future. System replacement is highly recommended. **turned call over to Darren who

Performed estimate to relocate Condenser. New condenser location would require running new electrical, new electrical disconnect box and whip, new copper refrigerant lines, new metal flashing. Electrical lines and refrigerant lines would have to get ran through the attic and out the side of the home to the new condenser location. This would be covered and protected by metal flashing. Per Andrew, price quoted was $2,441.00 for all work to be performed. Homeowner said he will give us a call should he decide to move forward. No work performed. **price given does not include any refrigerant adding that may be needed once work is completee should the unit need more refrigerant.

return for city corrections /change fuse

Performed Diagnostic on 2012 Trane system. Richard states that the system is no longer blowing out cold air. It stopped working last summer and hasn’t worked again since. I cycled system for cooling. Indoor unit kicked on normally. Outdoor unit is unresponsive. After diagnosis found a bad secondary motor control which is not allowing system to kick on. Primary motor control is also very pitted on contact point. Went over findings and recommendations with homeowner. With homeowner approval went ahead and replaced primary and secondary motor controls, and also added compressor saver kit to unit. Cycled system on, system now kicking on and cooling. Refrigerant levels are in range and system is producing an efficient temperature split. System is fully operational upon departure. Homeowner signed up on yearly ESA maintenance program. Waived today’s diagnostic fee.

Performed Fau maint on 2007 furnace. Cycled furnace for heat. Verified proper heating sequence of operations. Temperature rise across heat exchanger is within range. Indoor blower motor amps are slightly high, and there is a lot of oil loss present on the fan blades coming from the indoor motor. Recommend replacing indoor blower motor. Secondary motor control is in range. Tested and verified that heating components are working accordingly. Wiped down burner compartment. Wiped down exterior of unit. Homeowner fully understands the age of all of his equipment. Recommend replacing indoor blower motor to avoid any issues with heating or cooling. System is fully operational upon departure. Aftermarket Blower motor -$709.00 OEM Blower Motor- $1,009.00

Performed AC and FAU maintenance. Cycled system for heat. Verified proper heating sequence of operations. Temperature rise across heat exchanger is above rated limit. Amp draws are within range but high. Blower wheel is completely dirty. Motor appears to be leaking oil. System had 2 filters in it. Removed mesh filter and left pleated filter. Static pressure seems ok, seems like fan is not moving much air. Inspected heat exchanger, rivets are coming apart In certain areas, still no visible cracks. Inspected ductwork, ductwork is old and inefficient and plastic lining is actually starting to come apart in some areas. Cycled system for cooling. Checked outdoor system electric and system components. Amp draws are in range but fairly high. Primary motor control is very loud. Secondary motor control is falling out of range for compressor side. Refrigerant levels seem a tad bit low as system is only producing a 15 degree temperature split. System could use some work but overall System is oper

Furnace inspection

Replace existing rooftop unit with new Lennox 16 SEER 2 stage 3-Ton Heatpump. New Down-flow adjustable roof curb with sheet metal drops. Roofing service to properly seal new penetrations. New Electrical disconnect and whip. Replace and re-design duct system with new R-6 Class 1 with balancing dampeners. All Permits and HERS testing included.

Upon arrival performed maintenance on a 2009 system. Indoor motor is good. Blower wheel and evap coil dirty and need cleanings. Heat exchanger has some heat marks. Duct work is undersized, for the system. Air restrictions throughout system will cut the life span of the system. Secondary motor control is low. System was reset tested and fully functional upon departure .

Upon arrival performed maintenance on a 2009 system. Indoor motor is good. Blower wheel and evap coil dirty and need cleanings. Heat exchanger has some heat marks. Duct work is undersized, for the system. Air restrictions throughout system will cut the life span of the system. Secondary motor control is low. System was reset tested and fully functional upon departure .