Lake Forest CA Air Conditioning and Heating Services

Performed a heating maintenance on 2016 Lennox system. Checked electronic components, safeties and for normal operation

Combo tune up on Lennox equipment.

Performed a furnace maintenance on a Lennox system. Checked temperature splits, safety switches, and overall functionality.

Performed a furnace maintenance on a Lennox system. Checked the heat exchanger, air flow quality, and temperature rise.

Combo Tune Up

Performing safety inspection

Performed maintenance on Lennox condenser.

Ac maintenance

Ac maintenance

Ac maintenance

Ac maintenance

Ac maintenance

Ac maintenance

Ac maintenance

Ac maintenance

Upon arrival performed maintenance on heating system. Client had an extra filter for replacement. Filter was replaced. Indoor motors and blower wheel are in good condition. Circuit board and Elecricals are good. Amperage’s are in range. Motors are running efficient. Gas valve in working order. Cleaned flame sensor. System is operational upon completion.

Upon arrival performed maintenance on heating system. Client had an extra filter for replacement. Filter was replaced. Indoor motors and blower wheel are in good condition. Circuit board and Elecricals are good. Amperage’s are in range. Motors are running efficient. Gas valve in working order. Cleaned flame sensor. System is operational upon completion.

Upon arrival performed maintenance on heating system. Client had an extra filter for replacement. Filter was replaced. Indoor motors and blower wheel are in good condition. Circuit board and Elecricals are good. Amperage’s are in range. Motors are running efficient. Gas valve in working order. Cleaned flame sensor. System is operational upon completion.

Upon arrival performed maintenance on heating system. Client had an extra filter for replacement. Filter was replaced. Indoor motors and blower wheel are in good condition. Circuit board and Elecricals are good. Amperage’s are in range. Motors are running efficient. Gas valve in working order. Cleaned flame sensor. System is operational upon completion.

Performed a heating maintenance 2020 comfort pro. Cleaned and Adjust Burners. Check Combustion Air for Proper Venting. Examine the Heat Exchanger for Damage / Corrosion. Test Furnace Safety Controls. Inspect Gas Piping. Tighten Electrical Connections. Measure the Voltage and Amperage. Flush the Condensate Drains. Measure Tempurature Difference between Supply and Return Air. Vacuum Furnace Return Grille. Adjust Gas Pressure & Pilot. Clean in-place Blower Compartment. Inspect Blower Wheel for Proper Balance. Check the System's Static Pressures to Ensure Proper Airflow. Inspect Duct Connections for Air Leaks / Sizing / Insulation. Check all System Safety and Limit Switches. Clean Flame Sensor. Inspect Carbon Monoxide Detector. Check Thermostat for Proper Operation / Calibration. Filters where not changed this visit. System was fully operational on time of departure.

Arrived on site to perform heating tune up on a 1 year old unit. Client stated no issue as he just started using heater. Cycled on and is operational. Filter was supplied and replaced. Inspected blower compartment and electrical. Blower wheel is good. Motor is in range. Inducer motor is good and in range. All safety switches are operational. Flame sensor and igniter good. Drain lines are good and clear at this time. Temperature rise is good and in range. Found no protection on unit and recommended adding to protect from electrical surge and power outages. Cycled unit to ensure system operating. Wet over how unit is running and it’s condition. Client is aware he did declined recommendation at this time. Unit is operational upon departure.

Performed maintenance on 6 year old Lennox system. Cycled system for cooling. Checked indoor unit electrical and system components. Temperature split is in Range. Replaced filter with filter provided by homeowner. Checked outdoor unit electrical and system components. Refrigerant levels in range. Primary and secondary motor control are in good condition. Pulled condenser motor and thoroughly washed out condenser coil inside and out. Went over findings and recommendations. Cycled system, system is operational upon departure.

Check System Static Pressures Check all Safety and Limit Switches Clean Condenser Coil Duct Leakage Inspection Remove Debris from the Condenser Check Refrigeration Pressures Perform Visual Inspection and Clean Service Panel Measure Starting Amperage of the Compressor Tighten Electrical Connections Measure System Amperage and Voltage Flush Condensate Drain Lines Measure Temperature Difference Vacuum Furnace Return Air Grille Clean in Place Blower Compartment Inspect Blower Wheel for Proper Balance Monitor Air Purification System Apply UV Protective Coating on Condenser Perform Energy Usage Calculation Test Condenser Pressure Switches Check Thermostat for Proper Operation / Calibration

Check System Static Pressures Check all Safety and Limit Switches Clean Condenser Coil Duct Leakage Inspection Remove Debris from the Condenser Check Refrigeration Pressures Perform Visual Inspection and Clean Service Panel Measure Starting Amperage of the Compressor Tighten Electrical Connections Measure System Amperage and Voltage Flush Condensate Drain Lines Measure Temperature Difference Vacuum Furnace Return Air Grille Clean in Place Blower Compartment Inspect Blower Wheel for Proper Balance Monitor Air Purification System Apply UV Protective Coating on Condenser Perform Energy Usage Calculation Test Condenser Pressure Switches Check Thermostat for Proper Operation / Calibration

System totals out $15,805 - Client is only liable for the payment of $12,805 as Tech Clean California Rebate covers remaining $3,000 balance. UPDATED INVOICE DETAILS-- Payment collected by technician on April 8, 2022 of $1,385 was refunded on to the original install price- New install price is $14, 402--- Client is liable for $11,402 and $3,000 will be covered by CA Tech Rebate