Lake Elsinore, CA

Arrived on site to install parts. Once parts were installed found that R22 refrigerant pressures were extremely low which will result in it getting worse. This is an indication there is a leak present within the refrigeration cycle and will be sending over a long-term solution replacement options as client requested. I will follow up on Wednesday in regards to replacement and will be adding a one-week reimbursement to repairs if a decision is made within this time

Upon arrival unit was operational and heating. Checked furnace amps they were in range, condensation line was free blower wheel was free of oil. Safety switches were functioning properly, temp rise was in range. Furnace had electrical heating. Upon departure unit was operational and heating.

Upon arrival performed maintenance. Amperage’s on motors are in range. Circuit board and electrical connections good. Filter need to be replaced, client ordered some filters. Zoning in working order. Dusted off electrical connections. Indoor blower wheel beginning to accumulate dust levels. System is operational upon completion.

Upon arrival performed maintenance. Amperage’s on motors are in range. Circuit board and electrical connections good. Filter need to be replaced, client ordered some filters. Zoning in working order. Dusted off electrical connections. Indoor blower wheel beginning to accumulate dust levels. System is operational upon completion.

Upon arrival performed maintenance. Amperage’s on motors are in range. Circuit board and electrical connections good. Filter need to be replaced, client ordered some filters. Zoning in working order. Dusted off electrical connections. Indoor blower wheel beginning to accumulate dust levels. System is operational upon completion.

Upon arrival performed maintenance. Amperage’s on motors are in range. Circuit board and electrical connections good. Filter need to be replaced, client ordered some filters. Zoning in working order. Dusted off electrical connections. Indoor blower wheel beginning to accumulate dust levels. System is operational upon completion.

Arrived on site To perform AC diagnostic on 2006 condensing unit. Upon arrival Israel stated that the dogs have chewed up the low-voltage wires outside and the fan is not kicking on as well at the outdoor condenser. Klein turning it on and found that condenser fan motor was locked up due to failed bearing. I tried to pull the power disconnect out from the wall and 1/2 of it stayed stuck inside due to it melting from high amp draw. Unfortunately there is a fencing built around the entire unit with a padlock holding the top latch shut so Israel will be getting this remove so that Service can be fully completed. Will be calling Client tomorrow to finance repairs on 12 month no interest. Client will call us once fence is fully removed to schedule repair

During my twenty point heating inspection, I started with the thermostat. Giving a call for heating, and going to furnace to start maintenance. Temp rise of 30-60 needed, I got a temp rise of 42. House heats up to designated temperature. I checked out blower motor of any dirt or debris and it’s clean. No gas leaks detected in system. Hot surface igniter not cracked or having white spots. Flame sensor still working good, no need to be cleaned. Ducting done correctly, and all runs intact. Inducer motor is working efficiently. House heats good and ready for winter.

Client stated water leak inside attic -I found a leaky water line in the attic and let my client know that it is a plumbing issue that is causing that water leak -Client is aware and called a plumber out to fix -I completely the furnace maintenance as well -Filter was replaced -Electrical connections tightened -Flame sensor was cleaned off -Inducer motor and blower motor reading proper resistance -Secondary motor control was out of range 5/7.5 and needed to be replaced to ensure everything is working smoothly -It was replaced -System is tuned

Arrived on site to perform heating tune up on a 6 year old Goodman heater. Client stated no issues and is working good. Filters just got replaced. Cycled heater and is operational. Found black flex ducting used. Blower assembly and wheel good slight dust Motor is in range. Inducer motor is good and in range. Temperature rise is good and in range. Flame sensor and igniter is good. Drain lines are good. Safety switches are operational. Found no protection on units and recommended adding protection to protect systems and electrical components from electrical surges and power outages that can damage or even short out system or components. Cycled unit and went over how unit is running and it’s condition. She is aware and did hold off on recommendations. Cycled unit and unit is operational and heating upon departure.

Arrived on site for a leaking unit on side of home. Client stated it’s been going on for the past 5 years and would like someone to look at it. He stated unit does run and cooling just the leaking on the side is a issues. Inspect attic and found lines clogged up and not draining. Advised could be up in attic or under sink where it terminates at. Recommend doing a heavy clear out to clean both up top and bottom. To ensure is draining. Found no daft over flow switches on lines and second drain lines is also routed to back up pan and advised not a good design would recommend reworking lines and adding a safety over flow to secondary pan. Client is aware of issues and repairs needed. He stated he is going to try and do it himself as he is handy. He stated if it didn’t work we would come back out to clear lines with a heavy clear out then. He is aware and did hold off for today. Unit is operational but advised to not run unit until he clear line out. He is aware and stated he will do la

Performed heating tune up on 7 year old Goodman furnace. Cycled system for heat. Verified proper heating sequence of operations. Verified temperature rise across heat exchanger is within range. Ran system through 20 point inspection. Cleaned sensor. Tested all safeties. Secondary motor control for indoor fan has fallen out of Range. Homeowner recently replaced filters. Went over findings and recommendations. With approval, replaced secondary motor control. System is fully operational upon departure.

Parts, labor, pull deep vacuum, nitrogen pressure test, full r410a charge up

Client stated no air flow -I found blower capacitor within range -The blower motor itself has gone bad and needs to be replaced -Client is not able to move through with repairs at the moment

Cleaned the drain pan. Installed bracket for the condensate line to improve the slope of the drain in the attic.

Arrived on site to diagnose a no cooling down unit. Upon arrival spoke with client and she stated unit has been running and isn’t cooling home down. Past days unit has ran all day and doesn't go under 80 degrees in home. Advised out door coil and found no dye. Inspected indoor unit and evaporator coil. Inspected with U.V light and found that the Indoor coil developed a decent size leak. Advised client and son due to where the leak is present it is not repairable and would have to replace evaporator coil minimum to get unit cooling again. Wife spoke it over with husband and son. They decide to just replace evaporator coil for now. Advised will need to collect a $1000 deposit and will be ordering the coil to come in between 2-3 days. Got clients on the schedule for the 4th from 12-2pm if the coils come in. They are aware and advised u it is operational just not going to be cooling and running longer. They are aware and okay with it and will be expecting us next week for installation. U

Collected $1000 down with cash, $5000 down by check number 6777. The balance of 8344 will be paid by GreenSky financing

When I arrived at house, I was here to do a leak check on system. I put in dye last visit, now I plan on finding leak. I inspected my pressures and he lost refrigerant from last visit. Checked out the condenser coil for any green dye or a oil residue. I didn’t find anything at condenser. I then went up to coil to find leak. I popped open coil and noticed the bottom of coil starting to corrode. There was two spots where it could have potentially leaked from. I showed owner pictures, so he could see corrosion and ice built up. Owner is very happy we found exactly where it’s coming from. He would like to speak with wife first, before making decision on coil. They will reach out to us to have supervisor come out.

Performed an AC maintenance on a 2020 Lennox system. System was chemically bathed and thoroughly washed. Checked pressures and temperature splits and both where in range. Checked all electrical components and everything was in range. Condensate lines where drained. Filters where swapped this year. System was fully operational at time of departure.

Performed an AC maintenance on a 2020 Lennox mini split system. System was chemically bathed and thoroughly washed. Checked supply vs return temperature’s on each of the heads and both where in range. Checked all electrical components and everything was in range. Pulled filters off the heads and washed them off. System was fully operational at time of departure.

Condenser was non operational upon arrival -Breaker was tripped due to compressor drawing way too much power -Compressor is on its last leg, client is aware breaker will keep tripping due to this -Some repairs were recommended, they will not exactly fix the root of the issue however -Refrigerant levels are within range -Filter was dirty, a new one was installed -Darren will be arriving to provide replacement options -System is currently cooling

No cooling -Condenser fan is not spinning -Capacitors are within range -Fan motor is extremely hot -Fan is seizing up and when it is manually spun, it sounds like the bearings are completely finished -Eddie would like us to come out on Saturday, October 8th to install the fan motor

Client stated system not working properly -I found the condenser coil to be extremely dirty, I cleaned it out -Filter was dirty as well and needed to be replaced -Evaporator coil was clean -Refrigerant levels were low -I charged 3 lbs of 410a refrigerant to get the system up to proper speculations -I also added a dye kit as there is an apparent leak in the system -Client is now apart of our comfort club maintenance program -System is currently cooling properly and efficiently

8.99% 180 months - $322/mo 18 month 0% same as cash also available

Arrived on site to perform diagnostic on a no cooling good unit. Unit is 10 years old. Client stated last week unit just ran and didn’t seem to be cooling. Cycled all 3 zone and inspected condenser and electrical compartment. Primary stater burnt up and worn out from age and operation. Secondary motor control is out of range and weak. Recommend replacing primary stater and secondary motor control. Fan motor is working hard but okay. Checked start up and run amps on compressor. Start up is hard and loud and recommended adding a compressor booster kit to help prevent hard start up and prolong the compressor. Run amps okay. Checked pressure and found unit to be really low. Advised possibility of a leak present. Recommend adding dye and sealant t to help trace the leak as they are hard to find. No protection inside and out and highly recommended adding protection due to the type of equipment they have and zoning. Cycled unit and went over all findings with wife and son and spoke over wi